9. Place the stand upright, then loosen the hand knobs of
holders “A” and “B” (two places). Next, spread open the pipes
at left and right.
If the stand wobbles, loosen the bolts on the holders of curved pipes
“L” and “R,” and adjust the height. After adjusting the height, tighten the
bolts on the holders.
Hand knobs
Holder bolts
10. Attach mount holder “L” to the top left of the stand, attach
mount holder “R” to the top right of the stand, and tighten
the respective hand knobs.
Mount holder L
7
Hand knobs
Mount holder R
8
11. Attach the pad mounts to mount holder “L” and mount holder
“R,” and rmly tighten the respective hand knobs.
* The tips of the mounts are sharp. Handle them with care.
Pad mounts
Hand knobs
9
12. Attach pad mount (ball type) to the snare pipe, and tighten
the hand knob.
Pad mount
(ball type)
10
Hand knob
13. Insert the three cymbal mounts into the holders of the curved
pipes, and adjust all the holders as shown in the illustration to
complete setup.
Pad mount (ball type)
10
Pad mounts
9
Cymbal mounts
11
Pad mount
* The tips of the mounts are sharp. Handle them with care.
Notes
• When setting up or storing the stand, be careful not to pinch the ngers
you use to handle the stand.
• Regarding the way of mounting a sound module, pads, or cymbals,
please refer to the owner’s manual supplied with them.
• The pad mount can be adjustable to slide through the holder.
Please keep the top of the pad mount
over the holder for securement in its
adjustment.
WARNING: Caution during setup
When setting-up, you must observe the following cautions.
If you fail to observe these cautions, the stand might overturn or fall,
causing injury.
• Do not spread the stand wider
than 1.2 meters (48 inches).
1.2 m (48”)
• Adjust the rod height so that
no part of any cymbal is higher
than 1.2 meters (48 inches)
above the oor.
1.2 m (48”)
• Attach the cymbals in such
a way that the center of the
cymbal does not extend
beyond the rear pipes of the
stand.
Center of cymbal must not
extend beyond rear of stand
OK Not OK
3. Using a drum key, loosen the bolt on the holder of curved
pipe “R,” then insert straight pipe “R.”
7 cm
Curved pipe R
3
Straight pipe R
5
Holder
Bolt
4. Position straight pipe “R” so that its tip protrudes by about
7 cm, and then tighten the holder.
Perform steps 5–8 of the assembly procedure with the stand laying
down on the oor; do not place it upright yet.
5. Use a drum key to loosen bolt of the holder “A” (attached to
the left-side pipe of the stand), and insert curved pipe “L” (of
the assembly you created in step 1–2) into holder “A” of the
stand.
Holder A
Bolt
Curved pipe L
2
Stand
1
As a general rule, insert curved pipe “L” until the mark on the pipe can
be seen through the gap in the holder.
After rmly inserting it all the way, use the drum key to rmly tighten
bolt.
Drum key
Bolt
Mark
6. Lower holder “B” (attached to the right-side pipe of the stand)
to the same position as holder “C” (attached to the left-side
pipe of the stand).
Holder B
Holder C
7 cm
7. Use the drum key to loosen bolt of the holder “B,” and insert
curved pipe “R” (of the assembly you created in step 3–4) into
holder “B” of the stand.
Holder B
Bolt
Curved pipe R
3
As a general rule, insert curved pipe “R” until the mark on the pipe can
be seen through the gap in the holder.
After rmly inserting it all the way, use the drum key to rmly tighten
bolt.
Mark
Drum key
Bolt
8. Use the drum key to loosen bolt of the holder “C,” and insert
the snare pipe into holder “C” of the stand.
After rmly inserting it all the way, use the drum key to rmly
tighten bolt.
Insert the end of the snare pipe that doesn’t have a cap on it into holder
“C.”
Holder C
Snare pipe
6
Cap
Bolt
Drum key
How to Set Up the Stand
Before you start assembling the stand, make sure that you have all of the parts.
No. Name Quantity
1 Stand 1
2 Curved pipe L 1
3 Curved pipe R (with Pad mount) 1
4 Straight pipe L (Long) 1
5 Straight pipe R (Short) 1
6 Snare pipe 1
7 Mount holder L 2
8 Mount holder R 1
9 Pad mount 2
10 Pad mount (ball type) 1
11 Cymbal mount 3
12 Drum key 1
13 Cable clip 4
14 Cable tie 2
1
2
3
4 5 6 11
7
8
12 13
14
9
10
Fully Assembled View
NOTE
• Be very careful, when you assemble and move the stand, to
make sure that you do not drop it on your hands or feet.
• Prepare an area in which you can perform the assembly
safely.
• Do not use a power tool (e.g., an electric screwdriver) to
assemble the stand. You risk damaging or stripping the
screws.
* If the drum stand is to be used for extended periods in the same
location, we recommend using a Roland drum mat (TDM series) to
prevent discoloration of ooring by the rubber feet.
1. Using a drum key, loosen the bolt on the holder of curved
pipe “L,” then insert straight pipe “L.”
Curved pipe L
2
Straight pipe L
4
Holder
Bolt
2. Attach mount holder “L” to straight pipe “L.” Then, after
pulling down straight pipe “L” until it can move no further,
tighten the bolt.
Holder
Bolt
Curved pipe L
2
Straight pipe L
4
Mount holder L
7
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After
reading, keep the document(s) where it will be available for immediate reference.
Roland and V-Drums are registered trademarks of Roland Corporation in the United States and/
or other countries.
This document explains the specications of the product at the time that the document was
issued. For the latest information, refer to the Roland website.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
About WARNING and CAUTION Notices
About the Symbols
ALWAYS OBSERVE THE FOLLOWING
Placement
• Do not paste stickers, decals, or the like to this instrument. Peeling
such matter o the instrument may damage the exterior nish.
• Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar the
surface.
• Do not place containers or anything else containing liquid on top of
this unit. Also, whenever any liquid has been spilled on the surface
of this unit, be sure to promptly wipe it away using a soft, dry cloth.
Maintenance
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Additional Precautions
• Since sound vibrations can be transmitted through oors and walls
to a greater degree than expected, take care not to allow such
sound to become a nuisance to others nearby.
IMPORTANT NOTES
USING THE UNIT SAFELY
Owner’s Manual
Copyright © 2017 ROLAND CORPORATION
* 5 1 0 0 0 6 0 5 4 6 - 0 2 *
2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN
ENA 23 Zone 1 nr. 1620 Klaus-Michael Kuehnelaan 13, 2440 Geel, BELGIUMImporter:
Manufacturer:
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless you are instructed to
do so in the owner’s manual. Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Refer all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland distributor, as
listed on the “Information.”
Do not use or store in the following types of locations
• Subject to temperature extremes (e.g., direct sunlight
in an enclosed vehicle, near a heating duct, on top of
heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness; or are
• Placed in a poorly ventilated location.
Do not place in an unstable location
Otherwise, you risk injury as the result of the unit toppling
over or dropping down.
Do not allow foreign objects or liquids to enter unit; never
place containers with liquid on unit
Do not place containers containing liquid (e.g., ower
vases) on this product. Never allow foreign objects (e.g.,
ammable objects, coins, wires) or liquids (e.g., water or
juice) to enter this product. Doing so may cause short
circuits, faulty operation, or other malfunctions.
Be cautious to protect children from injury
Always make sure that an adult is on hand to provide
supervision and guidance when using the unit in places
where children are present, or when a child will be using
the unit.
Do not drop or subject to strong impact
Otherwise, you risk causing damage or malfunction.
CAUTION
Use only stand manufactured by Roland
This stand for use only with specic Roland musical
instruments. See apparatus instructions. Use with other
models is capable of resulting in instability causing
possible injury.
Evaluate safety issues before using stands
Even if you observe the cautions given in the owner’s
manual, certain types of handling may allow the stand
to overturn. Please be mindful of any safety issues before
using this product.
Route all power cords and cables in such a way as to prevent
them from getting entangled
Injury could result if someone were to trip on a cable and
cause the unit to fall or topple.
Avoid climbing on top of the unit, or placing heavy objects on it
Otherwise, you risk injury as the result of the unit toppling
over or dropping down.
Disconnect all cords/cables before moving the unit
Damage or malfunction may result if you fail to disconnect
all cables before moving the unit.
Take care so as not to get ngers pinched
When handling the following moving parts, take care
so as not to get ngers, toes, etc., pinched. Whenever a
child uses the unit, an adult should be on hand to provide
supervision and guidance.
• Moving parts of the stand
Keep small items out of the reach of children
To prevent accidental ingestion of the parts listed below,
always keep them out of the reach of small children.
• Included Parts
Cable clips, cable ties
• Removable Parts
Screws, washers, nuts, springs, hand knobs
When you need repair service, access this URL and nd your nearest Roland Service Center or authorized Roland distributor in
your country.
http://roland.cm/service
Roland Service Centers and Distributors
Roland Service Centers and Distributors
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Roland MDS-4V Owner's manual
-
Roland TD-1DMK/TD-1DMKX Installation guide
-
-
-
Roland TD-07KV Installation guide
-
Roland TD-4 Owner's manual
-
-
Roland MDS-Grand 2 Owner's manual
-
-
Roland TD-17KV User guide