COPYRIGHT © JANUARY, 2015 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2017 (AB)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MANUFACTURED SINCE 01/15) #BB17217 PRINTED IN TAIWAN
The Model G0637HEP is the same machine as the Model G0637 except for the dual-filtration HEPA filter
system and the collector mounting brackets. Except for the differences noted in this insert, all other content
in the Model G0637 owner's manual applies to this machine.
: To reduce the risk of serious injury, you MUST read and understand this insert—and
the entire Model G0637 manual—BEFORE assembling, installing, or operating this machine!
If you have any further questions about this manual insert or the differences between the Model G0637HEP
and the Model G0637, contact our Technical Support at (570) 546-9663 or email [email protected].
MODEL G0637HEP
7
1
⁄2 HP DUAL-FILTRATION HEPA
CYCLONE DUST COLLECTOR
MANUAL INSERT
(For owner's manual revised August, 2017)
V1.11.17
-2-
Model G0442HEP/G0601HEP (Mfd. Since 01/15)Model G0637HEP (Mfd. Since 01/15)
The information contained herein is deemed accurate as of 11/23/2017 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3
Model G0637HEP
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0637HEP 7‐1/2 HP 3‐PHASE DUAL‐FILTRATION
HEPA CYCLONE DUST COLLECTOR
Product Dimensions:
Weight.............................................................................................................................................................. 939 lbs.
Width (side-to-side) x Depth (front-to-back) x Height...................................................... 96-1/4 x 52-1/2 x 139-1/2 in.
Footprint (Length x Width)............................................................................................................... 96-1/4 x 52-1/2 in.
Shipping Dimensions:
Carton #1
Type................................................................................................................................................ Wood Crate
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 824 lbs.
Length x Width x Height............................................................................................................. 90 x 39 x 43 in.
Carton #2
Type........................................................................................................................................... Cardboard Box
Content............................................................................................................................ HEPA Cartridge Filter
Weight.................................................................................................................................................... 119 lbs.
Length x Width x Height............................................................................................................. 53 x 27 x 35 in.
Carton #3
Type........................................................................................................................................... Cardboard Box
Content....................................................................................... HEPA Cartridge Filter and HEPA Stand Legs
Weight.................................................................................................................................................... 119 lbs.
Length x Width x Height............................................................................................................. 53 x 27 x 35 in.
Carton #4
Type........................................................................................................................................... Cardboard Box
Content.................................................................................. Filter Outlet Connector and HEPA Filter Adapter
Weight...................................................................................................................................................... 77 lbs.
Length x Width x Height............................................................................................................. 38 x 19 x 22 in.
Electrical:
Power Requirement..................................................................................................... 220V or 440V, 3-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 220V
Full-Load Current Rating.................................................................................................. 25A at 220V, 12.5A at 440V
Minimum Circuit Size.......................................................................................................... 50A at 220V, 20A at 440V
Connection Type........................................................................................... Permanent (Hardwire to Shutoff Switch)
Switch Type......................................................................... Remote Control Magnetic Switch w/Overload Protection
Voltage Conversion Kit.............................................................................................................. P0637119V2 for 440V
Recommended Phase Converter....................................................................................................................... G5845
Motors:
Main
Horsepower............................................................................................................................................. 7.5 HP
Phase.................................................................................................................................................... 3-Phase
Amps.................................................................................................................................................. 25A/12.5A
Speed................................................................................................................................................ 3450 RPM
Type........................................................................................................................... TEFC Induction (Class F)
Power Transfer ............................................................................................................................... Direct Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
Model G0637HEP (Mfd. Since 01/15)
-3-
The information contained herein is deemed accurate as of 11/23/2017 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 3
Model G0637HEP
Main Specifications:
Operation
Dust Collector Type.......................................................................................................... Two-Stage (Cyclone)
Approved Dust Types................................................................................................................................ Wood
Filter Type.......................................................................................................................... Cartridge and HEPA
Airflow Performance..................................................................................................... 3468 CFM @ 4.3 in. SP
Max Static Pressure (at 0 CFM)........................................................................................................... 14.73 in.
Main Inlet Size........................................................................................................................................... 10 in.
Inlet Adapter Included.................................................................................................................................... No
Machine Collection Capacity At One Time....................................................................................................... 4
Maximum Material Collection Capacity................................................................................................. 20 cu. ft.
Filtration Rating................................................................................................................ 99.97% @ 0.3 Micron
Filter Surface Area.............................................................................................................................. 261 sq. ft.
Bag Information
Number of Lower Bags..................................................................................................................................... 2
Lower Bag Diameter.......................................................................................................................... 22-7/16 in.
Lower Bag Length............................................................................................................................... 26-3/4 in.
Canister Information
Number of Canister Filters................................................................................................................................ 2
Canister Filter Diameter................................................................................................................... 19-11/16 in.
Canister Filter Length.......................................................................................................................... 47-1/4 in.
Collection Drum Size......................................................................................................................... 55 Gallons
Impeller Information
Impeller Type...................................................................................................................................... Radial Fin
Impeller Size.............................................................................................................................................. 18 in.
Impeller Blade Thickness.......................................................................................................................... 3/8 in.
Construction
Lower Bag...................................................................................................................................... Clear Plastic
Canister............................................................................................................................ Spun Bond Polyester
Frame....................................................................................................................... Steel Sheet Metal (13 ga.)
Impeller....................................................................................................................................................... Steel
Paint Type/Finish....................................................................................................................... Powder Coated
Blower Housing......................................................................................................................... 11-Gauge Steel
Body.......................................................................................................................................... 16-Gauge Steel
Collection Drum.......................................................................................................................................... Steel
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time ............................................................................................................. 4 Hours
Serial Number Location .................................................................................................................................. ID Label
Sound Rating ............................................................................................................................................. 78 – 80 dB
ISO 9001 Factory .................................................................................................................................................. Yes
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................................................... Yes
-4-
Model G0442HEP/G0601HEP (Mfd. Since 01/15)Model G0637HEP (Mfd. Since 01/15)
Inventory
Inventory
After all the parts have been removed from the
boxes, you should have the following items:
Inventory: (Figures 1–5) Qty
A. Upper Stand Braces ................................... 4
B. Upper Stand Legs ...................................... 4
C. Filter Adapter .............................................. 2
D. Control Box Bracket ................................... 1
E. Lower Stand Legs ...................................... 4
F. HEPA Support Leg (3 Pieces) ................... 1
G. Lower Stand Braces ................................... 4
H. Cyclone Mounting Brackets ....................... 4
Figure 2. Model G0637HEP inventory I–N.
I
J
K
L
M
N
Figure 3. Model G0637HEP inventory O–W.
O
P
Q
R
S
T
U
V
W
O. Blower Housing with Motor ........................ 1
P. Control Box ................................................. 1
Q. Remote Control .......................................... 1
R. Collection Drum Lid Latches ...................... 6
S. Casters 2" ................................................... 8
T. Collection Drum Lids .................................. 2
U. Upper Collection Drum Cylinders ............... 2
V. Collection Drum Clamps ............................ 2
W. Lower Collection Drum Cylinders ............... 2
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
I. Outlet Port .................................................. 1
J. Intake Cylinder Intake Cylinder .................. 1
K Cyclone Funnel (Small )..............................1
L. Intake Barrel ............................................... 1
M. Funnel Port ................................................. 1
N. Cyclone Funnel (Large) .............................. 1
Figure 1. Model G0637HEP inventory A–H.
A
B
D
E
F
H
C
G
Model G0637HEP (Mfd. Since 01/15)
-5-
AA. Gaskets (not shown):
— Intake Cylinder 3 x 6 x 1800mm ............ 1
— Outlet Port 3 x 6 x 1100 ........................ 1
— Cyclone Funnel (Large) ......................... 1
— Intake Barrel 3 x 6 x 2500mm ............... 1
— Cyclone Funnel (Small)
3 x 6 x 2200mm ..................................... 1
— Funnel Port 3 x 6 x 735mm ................... 1
— Drum Lid PVC Rubber Seals ................. 2
— Foam Tape 3 x 6 x 300mm ................... 1
AB. Duct Clamps 9" (not shown) ...................... 4
AC. Collection Bags (not shown):
— Collection Drums 640 x 1200mm ........ 12
— Canister Filters 570 x 600mm ............... 2
AD. Hardware (not shown):
— Hex Bolts
3
⁄8"-16 x
3
⁄4" ........................... 69
— Hex Bolts
3
⁄8"-16 x 1"............................ 38
— Hex Bolts
3
⁄8"-16 x 1
1
⁄4" ........................... 8
— Hex Bolts
5
⁄16"-18 x
3
⁄4" ......................... 22
— Hex Bolts
5
⁄16"-18 x 1" .......................... 16
— Hex Bolts
5
⁄16"-18 x 1
1
⁄4" ....................... 27
— Phillips Head Screws #10-24 x
3
⁄8" ...... 24
— Fender Washers
5
⁄16" .............................. 8
— Flat Washers
3
⁄8" ................................ 242
— Flat Washers
5
⁄16" ................................. 92
— Lock Washers
3
⁄8" ................................... 8
— Hex Nuts
3
⁄8"-16 ................................... 11
— Hex Nuts
5
⁄16"-18 .................................. 27
— Hex Nuts #10-24 .................................. 24
— Lock Nuts
3
⁄8"-16 ................................ 108
— Rubber Flange Gasket .......................... 1
— Outlet Flange Gaskets ........................... 4
— Barrel Gaskets 700mm .......................... 2
— Barrel Gasket 460mm ............................ 1
— Flange Gasket 9" ................................... 1
— Foam Tape Rolls 5 x 50mm .................. 2
Figure 5. Model G0637HEP Inventory AE–AL
AE
AH
AF
AG
AI
AJ
AK
AL
AE. Vacuum Hose Clamps 1
1
⁄4" ........................ 4
AF. Vacuum Hoses 1
1
⁄4" x 79" .......................... 2
AG. Vacuum Manifold ........................................ 1
AH. Vacuum Hose Clamps 2" ........................... 2
AI. Vacuum Hose 2" x 39" ............................... 1
AJ. Collection Drum Vacuum Rings ................. 2
AK. Cyclone Vacuum Port ................................ 1
AL. Vacuum Hose Clips .................................... 2
Figure 4. Model G0637HEP Inventory X–Z.
X
Y
Z
X. Flexible Ducts 9" x 25
1
⁄2" ............................ 2
Y. HEPA Canister Filter Assemblies ............... 2
Z. Canister Filter Bag Clamps ........................ 2
-6-
Model G0442HEP/G0601HEP (Mfd. Since 01/15)Model G0637HEP (Mfd. Since 01/15)
The HEPA cyclones are assembled largely the
same way as the regular cyclones, but with the
HEPA filter components being installed in place of
the regular canister filter assembly. To assemble
your HEPA cyclone, open the Assembly section
in the Owner's Manual and follow those steps only
when specified below.
Assembly
To assemble the G0637HEP:
1. Follow Steps 1–33 in the Assembly section,
beginning on Page 21 of the owner's manual.
In Step 13, replace original brackets (shown
in Figure 24 of the owner's manual) with
brackets provided (see Figure 1).
Figure 7. Dust collector assembled with provided
brackets and outlet gasket.
Brackets
Provided
Outlet
Gasket
2. Follow assembly instruction Steps 14 –27 in
owner's manual.
3. Position outlet gasket around opening on
blower housing (see Figure 7), then attach
outlet to blower housing (see Figure 8) using
(10)
3
⁄8" x 1" hex bolts, (20)
3
⁄8" flat washers,
and (10)
3
⁄8" nuts.
4. Assemble all three HEPA support leg
components (see Figure 9) using (8)
3
⁄8" x
1" hex bolts, (16)
3
⁄8" flat washers, and (8)
3
⁄8"
nuts. Then thread adjustable foot completely
into bottom of support leg.
Figure 8. Blower housing and outlet attached.
Blower
Housing
Outlet
x10
Figure 9. Assembled HEPA support leg
(comprised of three parts).
x8
To ensure the integrity of the HEPA filtration
system and prevent fine dust from leaking
out before it reaches the filters, we strongly
recommend using a general-purpose sili-
cone sealant on all mating surfaces dur-
ing the assembly process. For those com-
ponents assembled with a rubber gasket
between them, apply the sealant evenly on
both sides of the gasket before assembly.
Install Adjustable
Foot Here
Model G0637HEP (Mfd. Since 01/15)
-7-
8. Slip plastic collection bag around opening
under canister filter, and secure with metal
bag clamp (see Figure 13).
Figure 13. Installing collection bag under filter.
Bag Clamp
Plastic
Collection
Bag
9. Double-check that all nuts and bolts are
tightened. Congratulations, assembly is com-
plete.
Figure 14. G0637HEP filter system completely
installed.
7. Attach square rubber gaskets to outlet (see
Figure 12), then secure filter adapter assem-
bly using (8)
3
⁄8" x 1" hex bolts, (16)
3
⁄8" flat
washers, and (8)
3
⁄8" nuts.
6. Attach square rubber gaskets to filter housing
(see Figure 11), then secure filter adapter
assembly using (8)
5
⁄16" x 1" hex bolts and (8)
5
⁄16" flat washers.
Figure 11. Filter components assembled.
Filter Housing
Rubber
Gasket
Filter Adapter
5. Attach HEPA support leg assembly to outlet
(see Figure 10) using (4)
3
⁄8" x 1" hex bolts,
(8)
3
⁄8" flat washers, and (4)
3
⁄8" nuts. Then
adjust foot until it touches floor.
Figure 10. HEPA support leg attached to outlet.
Outlet
HEPA
Support Leg
x4
Figure 12. Attaching filter assembly to outlet.
Rubber
Gasket
Filter Adapter
Filter Assembly
-8-
Model G0442HEP/G0601HEP (Mfd. Since 01/15)Model G0637HEP (Mfd. Since 01/15)
Main
1-1
1-2
1-3
1-4
1
2
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
45
46
47
205
201
201
201
225
226
223
223
222
228
89
89
89
89
89
91
91
91
91
91
48
49
50
51
52
54
55
57
58
59
61
62
63
63
64
66
67
68
68
69
70
71
72
73
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
270
93
94
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
109
110
110
111
115
135
137
138
139
140
141
142
143
144
145
146
147
148
149
150
153
154
155
156
157
8
20
89
143
232A
148
58
102
89
115
107
110
1-7
1-8
119
158
G0637HEP 440V
119-1
119-2
119-3
119-4
119-5
119-6
3-3
3-4
3-1
3-2
3-5
G0637HEP 220V
201
224
202
229
230
230-1
230-5
230-6
230-2
229-1
208
208
204
207
207
230-4
230-3
231
203
117
206
20
89
112
113
114
116
117
118
227
60
65
56
53
Model G0637HEP (Mfd. Since 01/15)
-9-
Main Parts List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P0637HEP001 MOTOR 7-1/2HP 220V/440V 3-PH 68 P0637HEP068 FLAT WASHER 5/16
1-1 P0637HEP001-1 MOTOR JUNCTION BOX 69 P0637HEP069 HEX NUT 5/16-18
1-2 P0637HEP001-2 MOTOR JUNCTION BLOCK 70 P0637HEP070 HOSE CLAMP 9"
1-3 P0637HEP001-3 MOTOR FAN COVER 71 P0637HEP071 FLEXIBLE DUCT 9 X 25-1/2"
1-4 P0637HEP001-4 MOTOR FAN 72 P0637HEP072 COLLECTION DRUM LID
1-7 P0637HEP001-7 BALL BEARING P6308ZZ 73 P0637HEP073 DRUM SEAL TYPE-R 2.1M
1-8 P0637HEP001-8 BALL BEARING P6306ZZ 77 P0637HEP077 COLLECTION BAG 640 X 1200MM
2 P0637HEP002 MOTOR CORD 10G 4W 300V 78 P0637HEP078 COLLECTION DRUM 25GAL (UPPER)
3 P0637HEP003 MAG SWITCH ASSY 79 P0637HEP079 COLLECTION DRUM 35GAL (LOWER)
3-1 P0637HEP003-1 MAG SWITCH COVER 80 P0637HEP080 DRUM CLAMP
3-2 P0637HEP003-2 POWER SWITCH 81 P0637HEP081 HEX BOLT 5/16-18 X 3
3-3 P0637HEP003-3 CONTACTOR NHD C-35D 220V 82 P0637HEP082 HEX NUT 5/16-18
3-4 P0637HEP003-4 OL RELAY NHD NTH-28 24-28A 83 P0637HEP083 COLLECTION DRUM LID LATCH
3-5 P0637HEP003-5 CIRCUIT BOARD W/TRANSFORMER 84 P0637HEP084 PHLP HD SCR 10-24 X 3/8
4 P0637HEP004 REMOTE CONTROLLER 85 P0637HEP085 HEX NUT 10-24
6 P0637HEP006 MOTOR BASE 86 P0637HEP086 PHLP HD SCR 10-24 X 3/8
7 P0637HEP007 HEX BOLT 3/8-16 X 1-1/2 87 P0637HEP087 HEX NUT 10-24
8 P0637HEP008 FLAT WASHER 3/8 88 P0637HEP088 CASTER 2"
9 P0637HEP009 LOCK WASHER 3/8 89 P0637HEP089 FLAT WASHER 3/8
10 P0637HEP010 HEX NUT 3/8-16 90 P0637HEP090 LOCK WASHER 3/8
11 P0637HEP011 HEX BOLT 1/2-13 X 1-1/2 91 P0637HEP091 HEX NUT 3/8-16
12 P0637HEP012 FENDER WASHER 1/2 93 P0637HEP093 HEX BOLT 3/8-16 X 1-1/4
13 P0637HEP013 LOCK WASHER 1/2 94 P0637HEP094 FLAT WASHER 3/8
14 P0637HEP014 HEX NUT 1/2-13 95 P0637HEP095 LOCK NUT 3/8-16
15 P0637HEP015 IMPELLER 18" 96 P0637HEP096 UPPER STAND BRACE
16 P0637HEP016 FLAT WASHER 1-1/6 97 P0637HEP097 UPPER STAND LEG
17 P0637HEP017 HEX NUT 1-1/16-8 LH 98 P0637HEP098 HEX BOLT 3/8-16 X 3/4
18 P0637HEP018 GASKET 3 X 6 X 1700MM 99 P0637HEP099 FLAT WASHER 3/8
19 P0637HEP019 BLOWER 100 P0637HEP100 LOCK NUT 3/8-16
20 P0637HEP020 FLAT WASHER 5/16 101 P0637HEP101 HEX BOLT 3/8-16 X 3/4
21 P0637HEP021 HEX BOLT 5/16-18 X 3/4 102 P0637HEP102 FLAT WASHER 3/8
45 P0637HEP045 FILTER BAG CLAMP 545MM 103 P0637HEP103 LOCK NUT 3/8-16
46 P0637HEP046 COLLECTION BAG 570 X 600MM 104 P0637HEP104 LOWER STAND BRACE
47 P0637HEP047 INTAKE CYLINDER 105 P0637HEP105 LOWER STAND LEG
48 P0637HEP048 GASKET 3 X 6 X 1800MM 106 P0637HEP106 HEX BOLT 3/8-16 X 3/4
49 P0637HEP049 HEX BOLT 5/16-18 X 3/4 107 P0637HEP107 FLAT WASHER 3/8
50 P0637HEP050 FLAT WASHER 5/16 108 P0637HEP108 LOCK NUT 3/8-16
51 P0637HEP051 INTAKE BARREL 109 P0637HEP109 HEX BOLT 3/8-16 X 3/4
52 P0637HEP052 CYCLONE FUNNEL (LARGE) 110 P0637HEP110 FLAT WASHER 3/8
53 P0637HEP053 RUBBER GASKET 700MM DIA 111 P0637HEP111 LOCK NUT 3/8-16
54 P0637HEP054 HEX BOLT 5/16-18 X 3/4 112 P0637HEP112 CONTROL BOX BRACKET CSA
55 P0637HEP055 FLAT WASHER 5/16 113 P0637HEP113 HEX BOLT 3/8-16 X 3/4
56 P0637HEP056 RUBBER GASKET 700MM DIA 114 P0637HEP114 FLAT WASHER 3/8
57 P0637HEP057 HEX BOLT 5/16-18 X 1-1/4 115 P0637HEP115 HEX NUT 3/8-16
58 P0637HEP058 FLAT WASHER 5/16 116 P0637HEP116 PHLP HD SCR M6-1 X 16
59 P0637HEP059 HEX NUT 5/16-18 117 P0637HEP117 FLAT WASHER 1/4
60 P0637HEP060 RUBBER GASKET 400MM DIA 118 P0637HEP118 HEX NUT M6-1
61 P0637HEP061 CYCLONE FUNNEL (SMALL) 119 P0637HEP119 CONVERSION KIT 440V
62 P0637HEP062 HEX BOLT 5/16-18 X 1-1/4 119-1 P0637HEP119-1 MAGNETIC SWITCH COVER
63 P0637HEP063 FLAT WASHER 5/16 119-2 P0637HEP119-2 POWER SWITCH
64 P0637HEP064 HEX NUT 5/16-18 119-3 P0637HEP119-3 CONTACTOR MSN35-18D
65 P0637HEP065 RUBBER GASKET 9" 119-4 P0637HEP119-4 OL RELAY NHD NTH-15 10–15A
66 P0637HEP066 FUNNEL PORT 119-5 P0637HEP119-5 CIRCUIT BOARD W/TRANSFORMER
67 P0637HEP067 HEX BOLT 5/16-18 X 1-1/4 119-6 P0637HEP119-6 MOTOR CORD 12G 4W 600V
-10-
Model G0442HEP/G0601HEP (Mfd. Since 01/15)Model G0637HEP (Mfd. Since 01/15)
Main Parts List Cont.
REF PART # DESCRIPTION REF PART # DESCRIPTION
135 P0637HEP135 EXT TOOTH WASHER 1/2 204 P0637HEP204 HEX NUT 1/4-20
137 P0637HEP137 DRUM LID HOOK 205 P0637HEP205 OUTLET GASKET 456 X 226MM
138 P0637HEP138 RIVET 4 X 7MM BLIND, STEEL 206 P0637HEP206 HEX BOLT 5/16-18 X 1
139 P0637HEP139 VACUUM HOSE 1-1/4" X 79" 207 P0637HEP207 HEX BOLT 1/4-20 X 3/4
140 P0637HEP140 COLLECTION DRUM VACUUM PORT 208 P0637HEP208 FLAT WASHER 1/4
141 P0637HEP141 FLAT WASHER 5/16 222 P0637HEP222 OUTLET
142 P0637HEP142 HEX BOLT 5/16-18 X 3/4 223 P0637HEP223 FILTER ADAPTER GASKET
143 P0637HEP143 HOSE CLAMP 1-1/4" 224 P0637HEP224 FILTER ADAPTER
144 P0637HEP144 PORT PLUG 1-1/4" 225 P0637HEP225 HEPA SUPPORT LEG (TOP)
145 P0637HEP145 FOAM TAPE 3 X 6 X 300MM 226 P0637HEP226 HEPA SUPPORT LEG (MIDDLE)
146 P0637HEP146 VACUUM HOSE CLIP 2-1/2" 227 P0637HEP227 HEPA SUPPORT LEG (BOTTOM)
147 P0637HEP147 PORT PLUG 2" 228 P0637HEP228 ADJUSTABLE FOOT M16
148 P0637HEP148 HOSE CLAMP 2" 229 P0637HEP229 PULL WIRE RAIL COVER
149 P0637HEP149 VACUUM HOSE 2" X 39" 229-1 P0637HEP229-1 PULL WIRE
150 P0637HEP150 VACUUM MANIFOLD 230 P0637HEP230 HEPA FILTER BODY (RIGHT)
153 P0637HEP153 CYCLONE VACUUM PORT 230-1 P0637HEP230-1 HEPA FILTER OUTER
154 P0637HEP154 FOAM TAPE 3 X 6 X 300MM 230-2 P0637HEP230-2 HEPA FILTER 595 X 595 X 300MM
155 P0637HEP155 HEX BOLT 5/16-18 X 3/4 230-3 P0637HEP230-3 HEPA FILTER BOTTOM PLATE
156 P0637HEP156 FLAT WASHER 5/16 230-4 P0637HEP230-4 HEPA FILTER CAGE 595 X 595
157 P0637HEP157 COLLECTION DRUM VACUUM RING 230-5 P0637HEP230-5 HEPA FILTER 595 X 295 X 300MM
158 P0637HEP158 DRUM LID PVC RUBBER SEAL 2M 230-6 P0637HEP230-6 HEPA FILTER CAGE 595 X 295
201 P0637HEP201 HEX BOLT 3/8-16 X 1 231 P0637HEP231 HEPA FILTER BODY (LEFT)
202 P0637HEP202 TAP SCEW M4 X 12 232A P0637HEP232A HEPA FILTER KIT
203 P0637HEP203 PHLP HD SCR 1/4-20 X 3/4 270 P0637HEP270 COLLECTOR MOUNTING BRACKET
Model G0637HEP (Mfd. Since 01/15)
-11-
G0637HEP Labels & Cosmetics
120
121
122
123
133
134
124
126
127
128
129
130
131
132
125
REF PART # DESCRIPTION REF PART # DESCRIPTION
120 P0637HEP120 MACHINE ID LABEL CSA 128 P0637HEP128 EAR PROTECTION LABEL
121 P0637HEP121 GENERAL WARNING LABEL 129 P0637HEP129 MODEL NUMBER LABEL
122 P0637HEP122 RED HANDLE NOTICE LABEL 130 P0637HEP130 GRIZZLY.COM LABEL
123 P0637HEP123 ELECTRICITY LABEL 131 P0637HEP131 CONTROL PANEL LABEL
124 P0637HEP124 DISCONNECT POWER LABEL 132 P0637HEP132 REMOTE CONTROL LABEL
125 P0637HEP125 READ MANUAL LABEL 133 P0637HEP133 GRIZZLY GREEN TOUCH-UP PAINT
126 P0637HEP126 HANDS/OUTLET LABEL 134 P0637HEP134 GRIZZLY PUTTY TOUCH-UP PAINT
127 P0637HEP127 GLASSES/RESPIRATOR DC LABEL
/
