Gorenje SIVK6B1TL Owner's manual

Brand: Gorenje

Model: SIVK6B1TL

Category: Hobs

Type: Owner's manual

This manual is also suitable for

IT635ORAB

Gorenje SIVK6B1TL is a built-in glass ceramic induction cooking hob featuring four induction hotplates with Power Boost and Super Power Boost functions for rapid heating. It has a control panel with sensor buttons for easy operation and a digital display for monitoring cooking settings. The hob also includes a timer function, overheating safety device, and child safety lock for added convenience and safety.

INSTRUCTIONS FOR

USE, INSTALLATION,

AND CONNECTION

www.gorenje.com

601656

Built-in glass ceramic induction hob is intended solely

for use in households. Our products are packed in

environment-friendly materials which can be safely

recycled, disposed of, or destroyed. Respective packaging

materials are labeled accordingly. When the appliance is

outdated and you intend to dispose of it, please make

sure this is done in an environment-friendly manner. Take

it to an authorized collection center for waste household

appliances.

Instructions for use have been prepared for the user, and

describe the particulars and handling of the appliance.

These instructions apply to di erent models from the

same family of appliances, therefore you may ﬁ nd

information and descriptions that may not apply to your

particular appliance.

The appliance should be connected to the power supply

in accordance with the instructions from the chapter

“Electrical connections” and in line with the standing

regulations and standards. The connections should be

carried out by a qualiﬁ ed personnel only.

The rating plate with basic information is located

underneath the appliance.

Appliances are allowed to be mounted on one side next

to a high kitchen cabinet, the height of which may exceed

that of the appliance. On the opposite side however, only a

kitchen cabinet of equal height as the appliance is allowed.

Dear customer !

Instructions for use

Installation instructions

Rating plate

Fire hazard protection

GLASS CERAMIC INDUCTION BUILT-IN

COOKING HOB

601656

IMPORTANT - READ BEFORE USING THE APPLIANCE ......................................... 4

Safety percautions ........................................................................................................................4

Warnings............................................................................................................................................5

CERAMIC-GLASS COOKTOP ....................................................................................... 6

Operating the cooking hob ......................................................................................................7

Induction hotplate function principle .................................................................................. 7

Appropriate cookware for induction hotplates ..............................................................8

Power regulation ...........................................................................................................................9

Energy saving tips ......................................................................................................................10

HOB CONTROL ................................................................................................................ 11

Switching on the cooking hob ..............................................................................................11

Turning hotplates on ....................................................................................................................11

Turning hotplates o ...................................................................................................................11

Powering o the cooking hob ...............................................................................................12

Engaging the control unit lock / child safety lock .......................................................12

Remaining heat indicator .........................................................................................................12

Power Boost and Super Power Boost ...............................................................................12

Operation time limit ................................................................................................................... 13

Overheating safety device ......................................................................................................13

Timer .................................................................................................................................................. 14

Bridged cooking zones (only with some models) .......................................................15

Safety functions and error display...................................................................................... 16

CLEANING AND MAINTENANCE OF CERAMIC - GLASS HOB ............................ 17

Cleaning ............................................................................................................................................17

INSTALLATION ................................................................................................................ 18

Important warnings .................................................................................................................... 18

Installing the foam gasket ....................................................................................................... 19

Worktop cutout dimensions .................................................................................................. 19

Installation procedure ..............................................................................................................20

Lower kitchen cabinet ventilation slots .............................................................................21

Installation diagram ................................................................................................................... 23

CONNECTION TO THE POWER SUPPLAY ............................................................... 24

TECHNICAL INFORMATION ........................................................................................ 26

Rating plate ................................................................................................................................... 26

TABLE

601656

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

metal capabilities or lack of experience and knowledge

if they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play

with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

• WARNING: The appliance and its accessible parts become

hot during use. Care should be taken to avoid touching

heating elements. Children less than 8 years of age shall

be kept away unless continuously supervised.

• WARNING: Danger of ﬁ re: do not store items on the

cooking surfaces.

• WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in ﬁ re. Never try to

extinguish a ﬁ re with water, but switch o the appliance

and then cover ﬂ ame with a lid or a damp cloth.

• After use, switch o the hob element by its control and

not rely on the pan detector.

• WARNING: If the surface is cracked, switch o the

appliance to avoid the possibility of electric shock.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can

get hot.

• Do not use steam cleaners or high-pressure cleaners to

clean the cooking hob, as this may result in an electric

shock.

• The appliance is not intended to be controlled by external

timers or special control systems.

• Do not use the appliance outdoors.

IMPORTANT - READ BEFORE USING

THE APPLIANCE

Safety percautions

601656

• The appliance may only be connected to the power mains by an authorized service

technician or expert.

• Tampering with the appliance or non-professional repair thereof may result in risk of

severe injury or damage to the product. Any repairs may only be carried out by an

authorized service technician or expert.

• The appliance is intended solely for cooking. Do not use it for any other purpose, e.g.

for room heating. Do not place empty cookware on the cooking zones.

• If another electrical appliance is connected to a AC power socket near the appliance,

make sure the power cord does not come into contact with hot cooking zones.

• Do not store temperature-sensitive items underneath the appliance, such as cleaners or

detergents, spray cans etc.

• Using the glass ceramic hob as a storage area may result in scratches or other damage

to it. Never heat food in aluminium foil or in plastic containers on the cooking hob.

Such foil or containers may melt which can result in a ﬁ re or damage to the cooking

hob.

• Do not place objects like knives, forks, spoons, or lids on the induction cooking zone as

they can become very hot.

• Eventual mismatches in colour shades between di erent appliances or components

within a single design line may occur due to various factors, such as di erent angles

under which the appliances are observed, di erent coloured backgrounds, materials,

and room illumination.

The symbol on the product or on its packaging indicates that this product may

not be treated as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of thisproduct. For more

detailed information about recycling of this product, please contact your local city

office, your household waste disposal service or the shop where you purchased the

product.

Warnings

601656

1. Induction hotplate rear left

2. Induction hotplate rear right

3. Induction hotplate front left

4. Induction hotplate front right

5. Hob control panel

6. Bridged cooking zones

CERAMIC-GLASS COOKTOP

601656

• Ceramic glass hob is ﬁ tted with three or four hotplates.

Hob surface is completely ﬂ at and smooth, without

edges to accumulate dirt.

• The hob is ﬁ tted with high power induction hotplates.

Heat is generated directly at the bottom of the dish,

where it is most needed, without any losses through the

ceramic glass surface. This way the required extent of

energy is considerably smaller compared to traditional

heaters, which operate on radiation principle.

• Glass ceramic hotplate is not heated directly, but only

by return heat transmitted by the dish. This heat ﬁ gures

as “remaining heat” after the hotplate is turned o . The

induction hotplate generates heat from the induction

coil, installed underneath the ceramic glass surface. The

coil creates magnetic ﬁ eld at the bottom of the dish

(which can me magnetized) which in turn originates

whirling ﬂ ows of current which then heat the hotplate.

Induction hotplate

function principle

IMPORTANT!

• In case sugar or other heavily sweetened substance is spilled on the hotplate, wipe it

immediately and remove the sugar residues with a scraper although the cooking zone

is still hot, otherwise the hotplate may be damaged.

• Avoid cleaning the cooktop while the cooking zones are still hot, as you may damage

the hob.

A Hob on/o sensor

B Power level/residual heat displays

B1 The decimal point indicates the activated timer

function

C Cooking zone selection sensors

E Sensor (-) and (+)

H Clock display

BB1 E

Operating the cooking

hob

601656

• Induction hotplate will function perfectly only if

appropriate cookware is used.

• During cooking, cookware should be placed in the

middle of the cooking zone.

• The appropriate cookware is the one which enables

induction, for example steel, enamel or steel alloy

cookware. Pots made from steel alloy with copper or

aluminum bottom, or glass pots are inappropriate.

• When using a pressure cooker, keep an eye on it until

the appropriate pressure level is reached and settled.

First, switch the cooking zone to maximum power,

then reduce the power on time in compliance with the

pressure cooker manufacturer’s instructions.

• Only use cookware with ﬂ at bottom! Concave or convex

(indented or bulging) bottom may impede the operation

of overheat protection mechanism and the cooking hob

may become too hot. This could lead to cracks in the

glass surface and melting of the pan bottom. In case of

damage resulting from the use of unsuitable cookware

or overheating of empty, dried-out pots or pans (with

nothing in them), the warranty is void.

• When buying cookware, check if it bears the label

“allows induction”.

Only use cookware suitable for electric and

induction cooking, with a:

• thick bottom (at least 2.25 mm)

• ﬂ at bottom.

Cooking zone Minimum pan bottom diameter

Ø 160 mm Ø 110 mm

Ø 180 mm Ø 110 mm

Ø 200 mm Ø 145 mm

The magnet test

Using a small magnet, it is possible to check whether the

bottom of your cookware can be magnetized .Use only

cookware to which the magnet will stick.

Appropriate cookware

for induction hotplates

601656

Pan recognition

One of the many advantages of an induction cooking hob

is the pan, or cookware, recognition. Even if there is no

cookware on the cooking zone, or if a pan with a diameter

smaller than that of the cooking zone, is placed on it, no

heat is wasted. If the pan is much smaller than the cooking

zone, it may not be perceived / recognized by the cooking

zone. When the cooking zone is switched on, a symbol

“U” will light up on the power level display. If a piece of

cookware is placed on the cooking zone in the following

ten minutes, it will be recognized by the cooking hob and

the cooking zone will be powered up to the set cooking

level.

As soon as the pan is removed from the cooking zone,

power supply to the cooking zone is disconnected. If a

pan with a diameter smaller than that of the cooking zone

is placed on it, only the power required to heat up the pan

in use will be supplied.

The cooking zone can be damaged:

• If an empty pan is placed on it.

• Before placing the pan on the cooking zone, wipe

the pan bottom dry to enable the ﬂ ow of heat and to

prevent damage to the cooking zone.

• For cooking and frying, only use cookware that can

be magnetized, i.e. steel, enamel-coated, or cast iron

cookware. Only then will the induction cooking zone

operate.

Cooking zone heat power can be set to ten di erent levels.

The table lists some examples of use for each level.

Power regulation

Power setting Purpose

0O , using remaining heat

1 - 2

Maintaining warm food, slow simmer of smaller quantities (lowest

setting)

3 Slow simmer (continuation of cooking after a powerful start-up)

4 - 5 Slow cooking (continuation) of larger quantities, roasting larger chunks

6 Roasting, browning

7 - 8 Roasting

9 Cooking large amounts, searing/braising

“Power boost” setting for start of the cooking process; also suitable for

very large amounts of food

601656

• When buying cookware be careful in selecting size:

pot diameter usually refers to the top edge of the dish,

which is often larger than the dish bottom.

• Steam-pressure pots (economic pots), which use

pressure in tightly sealed interior, are especially

economic, and save both time and energy. Shorter

cooking time leaves more vitamins in food.

• Always leave enough water in steam-pressure pots,

otherwise it may result in overheating which may

damage both the pot and the hotplate.

• Always cover the cookware with lids of appropriate size.

• Use such dish size to accommodate the quantity of food

to be prepared. If you use excessively large pot for small

amount of food, you will consume considerably more

energy.

Energy saving tips

601656

• After connecting the glass ceramic hob to the power

mains, all symbols on the display will light up brieﬂ y. The

cooking hob is then ready for operation.

• The cooking hob is ﬁ tted with electronic sensors which

are activated by touching the designated surface areas

with your ﬁ nger for at least one second.

• Each time a sensor is activated, this is conﬁ rmed by a

beep.

• Do not place any objects on the sensor area. Make sure

the sensor area is always clean.

Touch the on/o sensor (A) and hold it for at least 1

second.

The cooking hob is activated »0« will appear on all power

level displays (B) and decimal points (B1) will ﬂ ash.

The following setting must be e ected in the next

ten seconds; otherwise, the cooking hob will be

switched o .

After you have switched on the hob with the on/o key

(A), you may activate the desired cooking zone within the

following 10 seconds.

• After you touch the sensor for the desired cooking zone

(C), »0« on the relevant power level display will be lit more

intensively.

• Touch the sensors »+« (E) and »–« (E) to set the power

level (1-9-P). Touching the »–« sensor ﬁ rst will set the power

level to 9.

Continuous pressing of »+» (C) or »-« (E) ssensor

the power level is automatically increased or

reduced. Another procedure is to change power

in steps is by intermediate touching of relevant

sensors.

• First, select the cooking zone you wish to switch o .

• Touch the »–« sensor (E) to set the power level to »0«. If

power level for all cooking zones is set to »0«, then the

hob will be switched o after 20 seconds.

Switching on the

cooking hob

BB1 A B

Turning hotplates on

Turning hotplates o

HOB CONTROL

601656

• The cooking hob may be switched o anytime by

touching the on/o sensor (A). All settings will be

deleted, except for the minute minder (see section

»Timer«).

By activating the control unit lock, you can prevent the

operation or use of the cooking zones. Thus, the control

unit lock also works as a child safety lock.

Activating the child lock

• The hob must be switched o .

• Press the (A) sensor to switch on the cooking hob.

Setting »0« will be indicated on all displays.

• Simultaneously press the (C) sensor for the rear left

cooking zone and the »–« sensor (E) and hold them for

approximately 3 seconds. After the beep, »L« will appear

for a few seconds on all displays.

The child lock is now activated.

Deactivating the child lock

• Press the (A) sensor to switch on the cooking hob. »L«

will appear on all display units.

• Simultaneously press the (C) sensor for the rear

cooking zone and the »–« sensor (E) and hold them for

approximately 3 seconds. Setting »0« will be indicated

on all displays. The child lock is now deactivated.

Glass ceramic hob also features remaining heat indicator

»H«. Hotplates are not heated directly, but through return

heat radiating from the dish. As long as the symbol »H« is

on after the hotplate was switched o , the remaining heat

may be used for warming up food or for melting.

Even when the symbol »H« disappears, the hotplate may

still be hot. Be careful of burns!

For rapid cooking, power boost can be activated for any

cooking zone. This will allow you to rapidly heat large

amounts of food using extra power.

Powering o the

cooking hob

Engaging the control

unit lock / child safety

lock

Remaining heat

indicator

Power Boost

601656

Note: The front left cooking zone features the super power

function. In a cooking zone with this function, extra power is

activated for ﬁ ve minutes; then, the zone switches to level 9.

Activating the Power Boost

• Press the relevant sensor (C) to select the cooking zone.

Use the »–« or »+« sensor (E) to choose the power level 9;

then, press »+« immediately.

»P« will appear on the power level display.

Deactivating the Power Boost

• Press the sensor for the selected cooking zone (C); then,

immediately press the »–« sensor (E). The »P« symbol

will disappear and the cooking zone will switch to power

level 9.

Safety switch o

Power setting

Hours lapse prior safety switch

o

1 8

2 6

3 5

4 5

5 4

6 1,5

7 1,5

8 1,5

9 1,5

P 1,5

Maximum continuous operation of a particular hotplate

is limited, and the duration is displayed in the above

chart. When the hotplate is switched o by the safety

mechanism, the indicator displays symbols »0«, or »H« in

case there is any remaining heat left.

Example:

Set the cooking zone to level 6 and leave it to operate for

a while. If the cooking zone setting is not changed, the

security mechanism will switch o the zone after one and

a half hour.

• The hob is ﬁ tted with a cooling fan which cools the

electronic components during cooking. The fan may

operate for a while even after the end of the cooking

process.

BE EB

Operation time limit

Overheating safety

device

601656

• Induction cooking hob is also ﬁ tted with a built-

in overheating protection device that protects the

electronic parts from damage. The protection device

operates at several levels. When the cooking zone

temperature increases considerably, the cooking power

is reduced automatically. If this is not enough, the power

of currently heated cooking zones is reduced further

or shut o entirely. In this case, »E2« will be indicated

on the display. When the hob has cooled down, entire

cooking hob power is again available.

• Select the timer by simultaneously pressing the »–«

and »+« sensor (E). Timer settings are displayed on the

upper two display units (H), during which time the lower

two display units are switched o .

• Timer setting is only displayed for 10 seconds; then, the

display switches back to power level.

You may choose two operating modes:

a) Shut-o timer – the timer function is connected to

the selected cooking zone. When the time expires, the

cooking zone is switched o automatically.

b) Minute minder – timer function only has warning/alarm

functionality. When the clock runs out, only an acoustic

signal is emitted.

• Activating and setting the timer

Select the timer by simultaneously pressing the »–« and

»+« sensor (E).

- If you have previously selected a cooking zone so that

the corresponding display unit is lit more intensively,

then the timer will be set for that cooking zone. The

decimal point next to the power level indicates that

the timer has been activated.

- The timer (minute minder) can also be set when no

cooking zone is selected, if you wish to be warned of

something other than the cooking process. Activated

timer (or minute minder) will be indicated with two

ﬂ ashing decimal points next to the display unit.

• Set the cooking time by pressing the »–« or »+« sensor

(E). (Pressing »–« ﬁ rst will set the timer to 30 minutes. If

you press and hold the sensor, the setting on the display

will change at an increasing rate.)

Timer

CEE

601656

• Value can be set from 01 to 99 minutes. Shut-o timer

can be set for each cooking zone.

• To check the remaining time, select the corresponding

cooking zone and activate the timer function. Press the

»–« or »+« sensor (E) to change the setting. (Press the

»–« and »+« sensor (E) simultaneously and sequentially

to choose between active settings.)

• When the set time expires, »00« will ﬂ ash on the

display; in addition, relevant decimal point will ﬂ ash

at the shut-o timer. A short beep will be heard. To

acknowledge and stop the beep, press any key; after 2

minutes, the beep will end automatically.

• Some models allow combining the two left cooking

zones into a single large connected cooking zone.

Thus, a large oval pan or a griddle can be placed on

the combined cooking ﬁ eld. The pan should be large

enough to cover both centres of the upper and lower

cooking zone.

• Maximum pan size: 40 cm by 25 cm. We recommend

using a baking dish or pan with a heavy bottom. During

cooking, the dish or pan will heat up. Be careful to

prevent burns.

• When placing the baking dish on the hob, make sure it

does not cover the control module.

Activating the cooking zone bridge

• Switch on the cooking hob by pressing the on/o

sensor (A).

• Simultaneously touch the two sensors for the left-

hand side cooking zones (C). The sign »inverted U«

will appear on the display unit for the rear left ﬁ eld to

indicate that the two cooking zones have been bridged.

• Set the desired cooking power for the bridged cooking

zone.

• To change the cooking power later on, ﬁ rst press the

sensor for the lower left cooking zone.

Note: The bridged zone does not allow the power boost

setting. Maximum available power level is 9.

Deactivating the cooking zone bridge

• Simultaneously touch the two sensors for the left-hand

side cooking zones. The sign »inverted U« will disappear

and the hob will be switched o .

• Both cooking zones will operate independently.

Bridged cooking

zones (only with some

models)

601656

The cooking hob is ﬁ tted with overheating protection

sensors. If the temperature rises too high, individual

cooking zones or even the entire cooking hob can be

temporarily switched o automatically.

Error, possible cause, solution

• Continuous beep and Er03 ﬂ ashing on the display.

- Water spilt over sensor surface, or an object placed

over the sensors.

Wipe the sensor surface.

• Flashing E/2

- The cooking zone has overheated. Wait until it cools

down.

• E/3 ﬂ ashes

- Unsuitable cookware that lacks ferromagnetic

properties. Use another pot or pan.

In case of an operation failure or if the fault /

error indication does not disappear, disconnect

the cooking hob from the power mains for a few

minutes (undo the fuse or turn of the main switch);

then, reconnect it to the power mains and turn on

the main switch key.

If the problems persist, call a service technician.

Safety functions and

error display

601656

After each use of the glass-ceramic hob, wait for it to

cool down and clean it; otherwise, even the smallest food

residue will be burnt onto the hot surface next time you

use the appliance. For regular cleaning and maintenance

of the glass-ceramic surface, use special conditioning

agents which form a protective layer on the surface,

shielding it from dirt. Before each use, wipe any dust or

other particles from the hob surface and pan bottom as

these could scratch the surface (Figure 1).

Careful: steel wool, abrasive sponges, and abrasive

detergents can scratch the hob surface. Glass ceramic

surface can also be damaged by aggressive sprays and

inappropriate or insu ciently shaken (mixed) liquid

cleaning agents (Figure 1 and Figure 2).

Signage may be worn when using aggressive or abrasive

cleaners or cookware with damaged bottom (ﬁ gure 2).

Light stains can be removed by a damp soft cloth; then,

wipe the surface dry (Figure 3).

Water stains can be removed using a mild solution of

vinegar; however, do not use this solution to clean the frame

(only with some models, as it may become dull. Do not use

aggressive sprays or decalciﬁ cation agents (Figure 3).

Heavier stains can be removed using special agents and

utensils for cleaning the glass-ceramic hobs. When using

these products, follow the instructions provided by their

respective manufacturers.

Make sure any residues of cleaning agents are thoroughly

removed, as they could damage the glass-ceramic hob

when the cooking zones heat up (Figure 3).

Remove stubborn and burnt residues with a scraper (ﬁ gure 4).

Be careful when handling the scraper to prevent injury.

Only use the scraper when dirt cannot be removed

with a wet cloth or special cleaners for glass

ceramic surfaces.

Hold the scraper at the correct angle (45° to 60°). Gently

press the scraper against the glass and slide it over the

signage to remove the dirt. Make sure the plastic handle

of the scraper (in some models) does not come into

contact with a hot cooking zone.

Do not press the scraper perpendicularly against

the glass and do not scratch the hob surface with

its tip or blade.

Cleaning

Figure 2

Figure 3

Figure 4

Figure

CLEANING AND MAINTENANCE OF CERAMIC-

GLASS HOB

601656

Sugar and sugar-laden food may permanently damage the

glass-ceramic surface (Figure 5); therefore, they should

be removed from the glass-ceramic surface as soon as

possible, although the cooking zone may still be hot

(Figure 4). Any change in the color of the glass-ceramic

surface does not a ect its operation or the stability of

the surface. Such discolorations are mostly a result of

burnt food residues or use of cookware made of materials

such as aluminum or copper; these stains are di cult to

remove.

Warning: All damage described above predominantly

relates to the aesthetics, i.e. appearance of the appliance

and do not a ect its functionality directly. Such errors

cannot be the subject of a warranty claim.

Figure 5

• Installation of the appliance into a kitchen worktop and its connection to the power mains may

only be performed by an adequately qualiﬁ ed technician.

• Veneer or other ﬁ nish of the piece of kitchen furniture into which the hob is to be built in

should be treated with heat resistant glue (100°C); otherwise, the worktop ﬁ nish may be

discolored or deformed.

• Cooking hob is dimensioned to be built into the worktop over a piece of kitchen furniture, with

a width of 600 mm or more.

• After installation, the front two fastening elements should be freely accessible from below.

• Hanging, or wall-mounted kitchen elements should be installed high enough not to interfere

with the work process.

• The distance between the cooking hob and the kitchen hood should be no less than indicated

in the instructions for kitchen hood installation. The minimum distance is 650 mm.

• The distance between the appliance edge and the adjacent tall kitchen furniture element

should amount to no less than 40 mm.

• Use of massive wood decoration plates or boards on the worktops behind the cooking hob is

permitted, if the minimum distance remains the same as indicated in the installation drawings.

• Minimum distance between the built-in cooking hob and the rear wall is indicated on the

installation drawing.

Important warnings

INSTALLATION

601656

Before inserting the appliance into the opening in the kitchen

worktop, the supplied foam gasket must be attached to the

lower side of the glass ceramic (glass) cooking hob (see

ﬁ gure above). Do not install the appliance without the foam

gasket!

The gasket should be attached to the appliance in the

following way:

- Remove the protective ﬁ lm from the gasket.

- Then, attach the gasket to the lower side of the glass,

approximately 2-3 millimetres from the edge (as shown in

the ﬁ gure). The gasket must be attached along the entire

length of the glass edge and should not overlap at the

corners.

- When installing the gasket, make sure that the glass does

not come into contact with any sharp objects.

NOTE!

On some appliances the gasket is already installed!

Installing the foam

gasket

Worktop cutout

dimensions

- SIVK6

min 20

558-560

min 600488-490

min 40

min 50

595-600

520

51-55

601656

• Cooking hobs can be installed into worktops that are 30

to 50 mm thick.

• If the board is thicker than 40 mm, its inner edge should

be trimmed, or ground (Figure A). Thus, su cient air

circulation will be provided.

• If the thickness of your counter top exceeds 30 mm,

then the opening for the hob should be made in the

middle of the oven, with su cient clearance from the

front edge of the counter top so that the induction hob

does not touch the oven shield.

• If you wish to install the induction hob into an existing

opening, make sure if this is possible given the required

installation dimensions (installation depth of 56 mm).

• Worktop must be placed absolutely horizontal.

• Suitably protect the edges of the cut aperture.

• By means of the supplied screws 4 fasten the supplied

tightening brackets 4 fasten to the front and the rear

side of the cooking hob and to the prepared aperture.

• Connect the cooking hob to the mains power supply

(see instructions for the connection of the cooking hob

to mains power supply).

• Insert the hob into the cut aperture.

• Press the hob ﬁ rmly towards the worktop from above.

Installation procedure

min 20

708-710

min 600488-490

min 40

min 50

750-755

520

51-55

Page is loading ...

Gorenje SIVK6B1TL Owner's manual

Brand: Gorenje

Model: SIVK6B1TL

Category: Hobs

Type: Owner's manual

This manual is also suitable for

IT635ORAB

Download PDF

report

Gorenje SIVK6B1TL Owner's manual

This manual is also suitable for

Gorenje SIVK6B1TL Owner's manual

Related papers

Other documents