Minolta bizhub 42 Installation guide

Brand: Minolta

Model: bizhub 42

Category: Multifunctionals

Type: Installation guide

This manual is also suitable for

bizhub 36

E-1

INSTALLATION MANUAL

A3EW-9591-00

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

Applied Machines: /

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Caution:

• For the detailed installation procedures for each

option, follow the instructions given in the corre-

sponding installation manual and perform the

procedures correctly. (Optional devices must be

installed after completing the main body instal-

lation.)

• When placing the machine on the floor, make

sure to use the paper feed cabinet or the desk

to secure the performance and the quality of

the product.

• Once the Power Switch is turned ON, do not

turn OFF it until the installation work has been

completed.

• Lifting the machine in an awkward position or

transporting it in a poorly balanced position

could result in personal injury. When transport-

ing the machine, assign an adequate number of

persons to the job and ensure that each person

can take a good position of not being exces-

sively loaded. Machine mass:

• Approx. 63 kg (139 lb)

PC-211

FS-529

Machine

DK-511

WT-510AU-201

FK-509

MK-601

Electronic system options

✱ Electronic system options

A3EW11A001AA

E-2

II. Installation space (unit: mm (inch))

bizhub 42 + PC-211 + FS-529

III. Pre-installation check items

1. Select a level and stable place for installing the

machine.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Accessory parts

Varies depending on the applicable marketing area.

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

1173 (46-3/16)

1187 (46-3/4)

458 (18-1/16)

327

(12-7/8)

94 (3-11/16)

976 (38-7/16)

729 (28-11/16)

807

(31-3/4)

1363 (53-11/16)

A3EW11A002AA

103

(4-1/16)

229

(9)

100

(3-15/16)

Name Q’ty

User’s guide holder 1

Quick guide

(Copy/Fax/Scan/Box operations)

Installation manual 1 set

User’s guide CD 1

CD-ROM 1 set

Paper size label 1

Label (Legal restrictions on copying) * 1

Label (IR Prohibited) 1

Power cord

Power cord instruction

Spacer

Developer 1

Mylar 2

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

E-3

V. Removing the machine

1. Unpack the packaging box and remove cushion-

ing materials and plastic bags from the box.

2. Hold onto the portions indicated in the illustration.

While keeping the machine level, take it out from

the box.

Caution:

Machine mass:

• Approx. 63 kg (139 lb)

• Make available collective manpower of an

appropriate size for transporting the machine.

• When attaching the machine, as the reference

fit the machine with the corner A and B of the

paper feed cabinet.

VI. Removing protective tape, packing and

other shipping materials

1. Remove the protective tapes and the protective

materials.

A1V4IXC010DA

A3EW11A003BA

A3EW11A004AA

A3EW11A005AA

A3EW11A006AA

A3EW11A005AA

A3EW11A007AA

E-4

2. Remove the protective tape from trays 2 and 3.

3. Open the right door and remove the protective

tape.

4. Push the lever in the direction of the arrow and

remove the spacer from the transfer roller.

5. Close the right door.

6. Unlock the scanner lock by sliding it towards .

VII. Mounting the accessory parts

Install the supplied spacer onto the back of the

main body.

Note:

This step may not be performed depending on the

applicable marketing area.

VIII. Installing the user’s guide holder

Install the user’s guide holder.

IX. Affixing the paper size label

Affix the paper size label.

For loading the paper as well as setting the paper

type, refer to the user’s guide.

* Affix the paper size labels under the labels that

show the number of the drawers.

A3EW11A008AA

A3EW11A009AA

A1UDIXC033DA

A3EW11A010AA

A3EW11A013AA

A1UDIXC006DA

Paper size label

A3EW11A014AA

E-5

X. Affixing the Label (IR Prohibited)

Affix the label (IR Prohibited) to the position shown

below.

XI. Affixing the label (Legal restrictions on

copying)

Affix the label (Legal restrictions on copying) to the

position shown below.

Note:

This step may not be performed depending on the

applicable marketing area.

XII. Loading the developer

1. Open the right door.

2. Remove the cover shown in the illustration.

(One screw)

Note:

• After removing the screw:

(1) Raise the cover slightly.

(2) Pull it out toward you.

• Do not touch, scratch, or otherwise damage the

photo conductor.

3. Disconnect the connector.

Note:

• Do not touch, scratch, or otherwise damage the

photo conductor.

• When pulling out the connector, use caution not

to break the cable.

A3EW11A026AA

Label (IR Prohibited)

8 mm

3 mm

A3EW11A027AA

Label

A3EW11A015AA

(1)

(2)

Photo

conductor

A3EW11A016AA

E-6

4. Remove the imaging unit (IU) by placing your fin-

gers under the hooks on its right and left sides,

and pulling it toward you.

5. Remove screws that secure the drum unit in posi-

tion. (Two silver screws each on the right and left

sides)

6. Detach the drum unit upward while slightly bend-

ing open its lower part (the shaded portion).

Note:

• Do not touch or scratch the photo conductor.

• Cover the drum unit, which has been removed,

with a protective cloth or similar tool.

7. Remove

the developing unit cover.

(Three screws)

8. Remove the toner supply port.

9. Remove the supplied sheets of mylar from the

paper backing.

A3EW11A015BA

A3EW11A017AA

Drum unit

Developing unit

Drum unit

Developing unit

A3EW11A017BA

A1UDIXC011DA

4040IXC078DA

A1UDIXC048DB

E-7

10. Attach the mylar sheets. (Two places)

Note:

Make sure that the collar is completely covered

with the mylar sheet.

11. Cut open one corner of the supplied developer

(aluminum packet), and pour evenly into the

developer chamber, while turning the gear in the

direction of the arrow.

Note:

• Turn the magnet roller in the direction of its nor-

mal rotation, and not the backward.

• Not touching the gear of A side.

• Be sure not to let developer get inside the col-

lar.

12. Remove the mylar sheets that were attached in

step 10. (Two places)

Note:

Discard the removed mylar sheets.

13. Reinstall the toner supply port.

Note:

Make sure of the correct mounting position and

direction.

14. Reinstall the developing unit cover, ensuring that

its tabs are fitted properly into the slits.

(Three screws)

15. Align the shaft of the developing unit with the

inner guide of the drum unit.

16. Slide the drum unit along the guide to check that

the positioning pin is properly aligned with the

mating hole.

Collar

4040IXC208DA

Collar

4040IXC209DA

Magnet roller

Developer

4040IXC077DA

4030U015AC

Tighten this screw first

E-8

17. Screw the drum unit in position. (Two silver

screws each on the right and left sides)

Note:

Use care not to touch or scratch the photo conduc-

tor.

18. Install the imaging unit (IU) in position.

19. Connect the connector.

20. Install the cover shown in the illustration.

(One screw)

Note:

Make sure that the hole of the cover is aligned with

the positioning pin of the machine.

Note:

• After setting the IU in place, do not close the

right door.

• After setting the IU in place, promptly plug the

power cord into an outlet and clear the counters

within one minute.

(See the next section for information on clear-

ing the counters.)

XIII. Connecting the power cord

1. Connect the power cord.

Note:

This step may not be performed depending on the

applicable marketing area.

A3EW11A018AA

Positioning pin

Shaft

Guide

Shaft

A3EW11A015CA

A1UDIXC014DA

Positioning pin

A1UDIXC007DB

Hole

A1UDIXE035DA

E-9

2. Plug the power cord into the power outlet.

XIV. Clearing the counters

1. Turn ON the Power Switch.

Note:

Though the control panel displays the message

that informs you that the right door is open, ignore

the message and perform the following steps.

2. Display the Service Mode screen. (For details of

how to display the Service Mode, see the service

manual.)

3. Touch “Supplies” o “Life Counter Clear”.

4. Touch “Drum Unit (K)”.

The message “Are you sure?” will appear. Touch

“OK”.

5. Take similar actions as step 4 for the following

items:

• Developing Unit (K)

• Developer (K)

6. Touch “Close” twice.

XV. TCR sensor adjustment

1. Close the right door.

2. Make sure that the Service Mode screen is dis-

played.

3. Touch “Printer Adjustment” o “TCR Sensor

Adjustment”.

4. Touch “Execute” o “OK”.

Note:

After touching “OK”, wait about 1 minute 30 sec-

onds as is.

5. Touch “Close”.

6. Touch “Close” on the Service Mode screen.

XVI. Installing the toner bottle

Note:

The toner bottle is not shipped with the machine.

Purchase one that is separately available.

1. From a height of about 10 cm, tap the toner bottle

against a table or other hard object four to five

times. Then turn it upside down and repeat the

same procedure.

Note:

Toner can be caked in the toner bottle. Be sure to

perform this procedure.

2. Shake the toner bottle well about five times in the

vertical direction. Then, turn it over and repeat

the same procedure.

3. To move toner to the toner supply port side in the

bottle, drop the toner bottle with the supply port

side down onto a table or other hard surface from

the height of about 10 cm several times.

C4004U139CA

1166O228AA

1166O095AA

A1UDIXC049DA

E-10

4. Open the front door and slide the toner hopper

out of the machine.

5. Remove the protective tape.

6. Open the toner holder and mount the toner bottle.

Note:

Place the toner bottle so that its seal surface faces

upward.

7. Close the toner holder.

8. Gently peel off the seal toward you from the bot-

tle.

Note:

Perform this procedure slowly, as toner can burst

out when the seal is peeled off.

9. Slide the toner hopper back into the machine until

it clicks into position. Then, close the front door.

XVII. Adjusting touch panel

1. Press the [Utility/Counter] key.

2. Touch “Accessibility” o “Touch Panel Adjust-

ment”.

3. Lightly touch the center of the “+” markers at four

places on the touch panel. (Touch in any order.)

Note:

Pressing the touch panel hard may cause dam-

age.

* When all the markers at four places have been

touched, the [Start] key turns blue and lights up

steadily blue.

4. Press the [Start] key.

5. Touch “Close.”

A1UDIXC015DA

A1UDIXC037DA

A1UDIXC016DA

Toner holder

Place the surface to which

the seal is adhered upward.

A1UDIXC017DA

A3EW11A019AA

E-11

XVIII. Setting gradation adjust

1. Load A4 or Letter size papers in the tray.

2. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

3. Touch “Printer Adjustment” o “Gradation Adjust-

ment”.

4. Touch “Max. Density Adjustment” o “Print” o

“OK”.

Test patterns are printed on two A4 or Letter size

papers.

5. Touch “Scan”.

Using the steps below, follow the panel display to

start scanning the test patterns:

(1) Place the test pattern (Max. density adjustment

sheet 1) face down on the document glass,

and close the original cover.

(2) Press the [Start] key.

The machine will start reading the test pattern.

(3) Similarly, repeat steps (1) and (2) for the other

test pattern (Max. density adjustment sheet 2).

6. After the scanning of the test patterns is com-

plete, return to the “Gradation Adjustment”

screen.

7. Touch “Gradation Adjustment” o “Print” o “OK”.

Test pattern will then be produced on the A4 or

Letter size paper.

8. Touch “Scan”.

Using the steps below, follow the panel display to

start scanning the test patterns:

(1) Place the test pattern (Gradation adjustment

sheet) face down on the document glass, and

close the original cover.

(2) Press the [Start] key.

The machine will start reading the test pattern.

9. After the scanning is complete, touch “Close”

three times.

XIX. Date/Time setting

1. Press the [Utility/Counter] key, and touch “Admin

Settings”. o Enter Admin password (factory set-

ting: 12345678). o Touch “Machine Settings” o

“Date & Time Settings”.

2. Set the following settings:

(1) Touch “DATE” o Set the date. o Touch “OK”.

(2) Touch “Time” o Set the time. o Touch “OK”.

(3) Touch “Time Zone” o Touch “+” / “-” and set

time zone. o Touch “OK”.

3. Touch “Close” three times.

A3EW11A022AA

A3EW11A022BA

A3EW11A022CA

E-12

XX. Install date

1. Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

2. Touch “System Settings” o “Installation Date”.

3. Touch “Installation Date”.

4. Touch “Delete”, and enter the year/month/day

using the numeric keypad.

5. Touch “OK” o“Register”.

6. Touch “Close” twice.

XXI. Unit change

Note:

This function allows the user to select the type of

message that will appear when the replacement

time arrives for each of the different units.

1. Make sure that the Service Mode screen is dis-

played.

2. Touch “Toner Change”.

3. Touch “User” or “Service”.

4. Touch “OK”.

XXII. Adjusting registration of paper

source options

1. Load trays 4 and 5 with A4 or Letter size papers.

2. Make sure that the Service Mode screen is dis-

played.

3. Touch “Printer Adjustment”.

1. Touch “Side Edge Adjustment”o“Tray 4”

2. Press the [Start] key.

A test print will be produced.

3. Measure widths B and C of the pattern on the test

printout, and check that the difference is within

the specified range.

Specifications: Width B - Width C = 0 ± 1.0 mm

4. If the difference between the measured widths B

and C is outside the specified range, enter the

correction value using the or key.

Adjustable range: -3.0 to +3.0 mm

(Step: 0.2 mm)

5. Print a test page again, and check if the differ-

ence is within the specified range.

* If the use of the or key does not allow

the measurement to fall within the specified

range, perform the following steps.

6. Slide out the drawer and unload paper from it.

7. Loosen the three screws shown in the illustration.

Paper exit

direction

A3EWPCA008AA

A0XWMXC018MB

E-13

8. Watching the graduations provided in the drawer,

move the edge guide in the rear.

• If the difference is greater than the specified

value, move the edge guide toward the front.

• If the difference is smaller than the specified

value, move the edge guide toward the rear.

9. Load paper and print another test page to check

the difference between widths B and C.

* Make adjustments until the difference falls within

the specified range.

10. Tighten the screws which has been loosened in

step 7.

* Adjust “Tray 5” using the same steps.

11. Touch “Close”.

1. Touch “Left ADJ Duplex” o “Tray 4”.

2. Press the [Start] key.

A test print will be produced.

3. Measure widths B and C of the pattern on the test

printout, and check that the difference is within

the specified range.

Specifications: Width B - Width C = 0 ± 1.0 mm

4. If the difference between the measured widths B

and C is outside the specified range, enter the

correction value using the or key.

Adjustable range: -3.0 to +3.0 mm

(Step: 0.2 mm).

5. Print a test page again, and check if the differ-

ence is within the specified range.

* Adjust “Tray 5” using the same steps.

6. Touch “Close” twice.

7. Touch “Close” on the Service Mode screen.

8. Turn ON/OFF the Power Switch.

Note:

If Service Mode was displayed, you must turn off

the power after exiting Service Mode, and turn it

back on after 10 or more seconds have passed.

XXIII. List output

1. Load tray 2 with A4 or Letter size papers.

2. Press the [Utility/Counter] key.

3. Touch “User Settings” o “Print Settings” o “Print

Reports”.

4. Touch “Configuration Page” o “Print” o “OK”.

Verify that the list is printed.

5. Print other lists (information) as necessary.

6. Touch “Close” three times.

XXIV. Connecting cables

1. Connect the network cable to the machine and

route the cable as shown in the illustration.

Note:

Fit the cable into the hooks.

2. Connect the networking equipment (HUB) using

the network cable.

Note:

The following shows the recommended network

cables that correspond to each communication

speed.

• 10BaseT/100BaseTX: Category 5

• 1000BaseT: Category 5E, Category 6

A0XWMXC019MA

A3EWPCA009AA

Paper exit

direction

A3EW11A020AA

E-14

XXV. Network setting

Make the TCP/IP address setting for the network.

Note:

The IP address is assigned automatically by the

DHCP server, when the machine's power is turned

ON. (DHCP setting at the time of factory shipment:

ON)

If the machine’s IP address is not set automatically,

follow the steps below to set it manually.

Note:

Consult the network adminisutrator for the setting

value to be entered and make settings as

required.

1. Press the [Utility/Counter] key.

2. Touch “Admin Settings”. o Enter Admin pass-

word. o Touch “OK”.

3. Touch “Ethernet” o “TCP/IP” o “DHCP” o

“OFF” o“OK”.

4. Set the following settings:

(1) Touch “Enable” o “ON” o “OK”.

(2) Touch “IP Address”. o Set it to an IP address

on the network of the machine. o Touch “OK”.

(3) Touch “Subnet Mask”. o Set the subnet mask.

o Touch “OK”.

(4) Touch “Gateway”. o Set the gateway address.

o Touch “OK”.

5. Turn OFF the Power Switch, then turn it back ON.

6. Press the [Utility/Counter] key.

7. Touch “User Settings” o “Print Settings” o “Print

Reports” o “Configuration Page” o “Print” o

“OK”, to print the settings list page, and verify that

the settings from step 4 have been completed

correctly.

Minolta bizhub 42 Installation guide

Brand: Minolta

Model: bizhub 42

Category: Multifunctionals

Type: Installation guide

This manual is also suitable for

bizhub 36

Download PDF

report

Minolta bizhub 42 Installation guide

This manual is also suitable for

Minolta bizhub 42 Installation guide

Related papers

Other documents