Denver TCU-61 User manual

Mp3

INSTRUCTION MANUAL

TCU-61

Before connection operating or adjusting this product

Please read these instructions completely

Please keep this manual.

-2-

USING AC POWER

Battery Operation

The battery compartment is located on the back of the cabinet.

* Remove the battery compartment door by pressing downward on the tabs as shown in figure 1 below.

* Insert 8 C size (UM-2) batteries into the battery compartment as shown in figure 2 below. Be sure to

observe the polarity markings which are engraved inside the battery compartment. If the batteries are

inserted incorrectly, the unit

will not operated.

* Replace the battery compartment door.

NOTE: The AC power cord must be disconnected from the AC socket on the back of the unit in order

for the unit to operate on battery power.

,

Using AC Power

1.Connect the AC power cord into AC Socket and Standard household wall outlet. The batteries will be

automatically disconnected. For dual voltage version. Make sure that the AC VOLTAGE SELECTOR is

switched to your local voltage.

2.Connect the power cord to the AC socket inlet and the wall outlet. the power supply is now

connected and ready for use.

3.To switch off completely, unplug the power cord from the wall outlet.

1.5V

8 x R14 C CE LL UM-2

Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

( OR BACK),NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO

RAIN OF MOISTURE.

This “bolt of lightning” indicates uninsulated materia within your unit

which may cause an electrical shock, for the safety or everyone in your

household, please do not remove product covering.

8 x R14 C CELL UM-2

CLASS 1

LASER PRODUCT

-1-

-3-

1.VOLUME KNOB

2.FUNCTION SELECT

3. EQ BUTTON

4. POWER BUTTON

5.REPEAT BUTTON

6.TIME/PROGRAM BUTTON

7.CASSETTE PLAY KEYS

8.CD DOOR

9.FM ANTENNA

10.STOP BUTTON

11.PLAY/PAUSE BUTTON

12.USB JACK

13. RANDOM BUTTON

14.MUTE BUTTON

15.BACK/NEXT KNOB

16.(PRE- UP BUTTON

PRE-DN BUTTON)

17.LCD DISPLAY

18.CASSETTE DOOR

19.AUX JACK

20. POWER SWITCH

21.BATTERY DOOR

22. AC SOCKET

-4-

17 18

13. RANDOM BUTTON

-In a CD/MP3/USB mode,

press this button can be played at random.

14.MUTE BUTTON

-Press the mute button allows CD/MP3/USB

AUX/the RADIO to enter the mute state.

15.BACK/NEXT KNOB

BACK KNOB

-BACK track selection.

-Rotate and hold more than 1.5 sec BACK

search intra track.

-In the radio mode, rotate BACK will enter

the low end of the manual channel scan mode.

NEXT KNOB

-NEXT track selection.

-Rotate and hold more than 1.5 sec

forward search intra track.

-In the radio mode, rotate NEXT will enter

the high-end manual channel scan mode.

16. PRE-UP/PRE- DN BUTTON

-In the radio mode, press PRE-UP button Mark

place to choose the next channel.

-In the mp3 mode, press PRE-UP button Mark

place enter into the next folder.

-In the radio mode, press PRE-DN button Mark

place to choose the back channel.

-In the mp3 mode, press PRE-DN button Mark

place to enter the back folder.

17

.LCD DISPLAY

-Show the FM dial frequency.

-Show the number of tracks.

18.CASSETTE DOOR

19. AUX JACK

-Press FUNCTION button ,

select MP3/AUX station.

Play MP3、DISCMAN、 WALKMAN AUX

insert when no disc.

NOTE: Please take out the CD disc.

20.POWER SWITCH

-To control the unit electrical source on/off.

21.BATTERY DOOR

-To open battery compartment.

22.AC SOCKET

-Inlet for power cord.

- Adjust volume level.

2.FUNCTION SELECT

-Select source of sound CD/USB/AUX/

TAPE/RADIO.

3.EQ BUTTON

-Press the button to change EQ CD/MP3/USB/

AUX/RADIO's music style.

-When playing the music, Press this button

is in the popular-jazz-FLR-classica-rock.

4. INTRO BUTTON

-Press the INTRO button into 10 seconds

browsing repertoire state.

5.REPEAT BUTTON

-Repeat a track CD/MP3/USB program.

-Repeat mode : normal->repeat 1->repeat all->

repeat album ->normal.

6. TIME/PROGRAM BUTTON

-In standby mode, press this button and then press

>>I and I<< to adjust the time.

-Program and review programmed track numbers.

-In the working status, press this button

can on CD/MP3/USB/RADIO for programming.

7.CASSETTE PLAY KEYS

PLAY ( ) - start playback

F.REW ( ) -rewind the tape

toward the beginning.

F.FWD ( ) -advance the tape

toward the end.

STOP/EJECT ( ) - stop the tape

- open the cassette compartment

PAUSE ( ) - interrupt recording or

playback

8.CD DOOR

-Lift the CD lid to open/close the CD door.

9.FM ANTENNA

-To improve FM reception.

10.STOP BUTTON

-Stop CD/MP3/USB playback;

erase a CD program.

11.PLAY/PAUSE BUTTON

-Start or pause MP3/CD/USB play.

-In the radio mode, press the play/pause button

enter the automatic channel scan mode.

12.USB JACK

-To listen to your

USB flash memory.

-Stick with MP3 music files.

1.VOLUME KNOB

1

Top and front panels (See fig )

FIG

19

22

21

- 1.5V + - 1.5V +

1.5V X 8

UM-2 OR"C"SIZE

+ 1.5V -

ON

OFF

20

189

15

12137

2

4

6

10

14

16

11

3

5

-

VOLUME

+

TUNING

English

CONTROLS

POWER SUPPLY

-5-

-6-

Radio reception

1.Press FUNCTION button select RADIO mode.

2.Tune to required station by BACK/TUNE DN or NEXT/ TUNE UP.

Manual Tuning: BACK or NEXT and then release within 1 sec.

Auto Tuning: Press the play/pause button enter the automatic channel

scan mode, and to be put automatically sets.

Preset Channel:(FM 30 Preset memories)

(1) BACK or NEXT button Select desired station.

(2) Press PROGRAM button once , The MEMORY number indicator begins steady in the display.

(3) Press PRESET-UP or PRESET DOWN buttons to select the desired number.

(4) Press PROGRAM button to save that station.

(5) Repeat steps (1) to (4) procedures for other stations.

3.After end of program. Press PRE-UP or PRE-DN to start play the frequency that you selected.

4. [VOL-]or [VOL +] to adjust the volume.

5.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.

6.Turn off the radio by press FUNCTION button select other mode or press power button to off the unit.

7.Switch on again after shut down, the memory frequency still exists.

rotate

Rotate

USE RADIO

、、 .

To listen music with a mp3 discman walkman

1.Connect to the AUX .

2.press function selector to AUX, the sound source of the mp3

or discman or walkman will output from the unit.

- the volume control to adjust the volume.

-The unit can't control the player.

Rotate

USE AUX

USING THE CASSETTE

UNDERSTANDING THE BUTTONS

PLAY - Press to play cassettes.

REW - From stop mode, press to rewind the tape toward the beginning.

F.FWD - From stop mode, press to advance the tape toward the end.

STOP/EJ. - Press to stop current tape activity or to open the cassette compartment door when

no buttons are active.

PAUSE - Press to interrupt tape play or record mode, press the second time to resume tape play

or tape record mode.

PLAY A CASSETTE TAPE

1.Press FUNC button select TAPE mode.

2.Press STOP/EJ.key to open the cassette compartment door.

3.Insert a recorded cassette and close the cassette compartment door.

4.Press PLAY to start playback.

5.To interrupt playback, press PAUSE ,To resume, press the key again.

6.Press REW/F.FWD to move tape to the desired starting point.

7.Adjust the volume to your desired listening level.

8.To stop the tape ,press STOP/EJ.

- The keys are automatically released at the end of the tape, except if PAUSE has been activated.

PROGRAM METHOD

(1)Press the [PROGRAM] key at STOP mode, system will go to PROGRAM mode.

-The PRG icon and P01 will blink at 2Hz. This prompts the user to enter the first songs in the

program PLAY list.

(2)The user can select the desire tracks by using [NEXT], [BACK] keys.

Once these keys are pressed, the Display will show the selected track.

(3)After select the desired track, press [PROGRAM] key again and it will be stored in the memory.

MP3 Maximum 99 and CD Maximum 20 tracks can be programmed when Repeat

steps (2) to (3) procedures.

(4)If press the [STOP] key during the program mode, then the selected TRACKS will be stored

in the memory and return to STOP mode (Continuous Play mode)

(5)If press the [PLAY] key during the program mode, it will start the program PLAY mode.

PLAY start from P01 Track

Erasing a program

You can erase the content of the memory by:

- While playing, press STOP button twice.

- Opening the CD door

- Select the other mode.

-7-

-8-

Note: at the mode of CD/MP3 / USB ,the lcd will

display the number of song or the song playing time.

-The unit don't support the HDD all and the

portion usb with mp3 player.

USB Audio functions

1)press function button or stop usb button to

choose the usb state.

2) PLAY/PAUSE

3) NEXT, BACK Skip search

4) Program Track(MP3 99 Track; CD 20 Track )

5) mode : normal->repeat 1->repeat all->

repeat album ->normal

6) Maximum Folder : 99 Folders

7) Maximum File : 999 Files

*Notice :

-When the unit has not the disc, inserting the

usb card will automatically real usb card,

it read the USB first

while having the USB.

Repeat

This CD-player can play Audio Discs,MP3 CD-R.

Do not try to play CD-ROM,CDi,VCD,DVD or

computer CD.

1.Press function button to CD state.

2.to open the cd door, press cd open button.

3.insert a mp3/cd or cd-r、with the printed side

facing up and press cd door gently to close.

4.press play/pause on the set to start playback.

5.Press the pause button to pause play, press

the play button back playing.

6.to stop cd playback , press stop.

note: cd/mp3 play will also stop when:

-you open the cd compartment;

-you select radio sound source;

-the cd/mp3 has reached to the end.

selecting a different track.

during playback you can use back or next to

select a particular track.

if you have selected a track number in the

stop or pause position, press play to start

playback.

next once briefly for the next track,

or press repeatedly until the desired track

number appears in the display.

back once briefly to return to the

beginning of a current track.

back more than once briefly for a

previous track.

finding a passage within a track

1. and hold down back or next.

the cd is played at high speed.

2.when you recognize the passage you want

release back or next.

normal playback resumes.

different play modes:repeat

repeat-play the current track continuously.

repeat all-plays the entire cd continuously.

playing tracks in random order after press

the random button, the tracks will be played

in random order.

Rotate

CD/MP3 PLAYER

CD/MP3 Player

Playing a CD/MP3

Playing a USBPlaying a USB

When the unit idle on USB/SD/CASSETTE/AUX mode

over 10 min. Then the unit will Power Off mode

automatically. for saving energy.

-

Power Off

Insert a CD,MP3, CD-R.

-CD badly scratched or dirty

•Replace/clean CD, see Maintenance

No CD/MP3 inserted

CD/MP3/USB playback does not work

CD/MP3 badly scratched/dirty/USB

Replace/clean CD/MP3

(see maintenance)

-Laser lens steamed up

•Wait until lens has adjusted to room

temperature

/USB

The CD/MP3 skips tracks

CD/MP3 damaged or dirty

Replace or clean CD/MP3

-Program is active

•Quit Program mode(s)

- CD-R is blank or the disc is

not finalized

Use a finalized CD-R.

No sound/power

-Volume not adjusted

•Adjust the VOLUME

-Power cord not securely connected

•Connect the AC power cord properly

-Batteries dead/incorrectly inserted

•Insert (fresh) batteries correctly

Display does not function properly/

No reaction to operation of any of the controls

-Electrostatic discharge

•Switch off and unplug the set. Reconnect

after a few seconds

Poor cassette sound quality

Dust and dirt on the heads, etc.

•Clean deck parts etc., seeMaintenance

-Use of incompatible cassette types

(METAL or CHROME)

•Only use NORMAL (IEC I) for recording

No disc indication

www.denver-electronics.com

Electric and electronic equipment contains materials, components and

substances that can be hazardous to your health and the environment,

if the waste material (discarded electric and electronic equipment) is not

handled correctly.

Electric and electronic equipment is marked with the crossed out trash can

symbol, seen above. This symbol signifies that electric and electronic

equipment should not be disposed of with other household waste,

but should be disposed of separately.

All cities have established collection points, where electric and electronic

equipment can either be submitted free of charge at recycling stations

and other collection sites, or be collected from the households.

Additional information is available at the technical department of your city.

Please fill the blank with the model number of this player for future reference

Importer:

DENVER ELECTRONICS A/S

Stavneagervej 22, DK-8250 EGAA, DENMARK

www.facebook.com/denverelectronics

-9-

Page is loading ...

Denver TCU-61 User manual

Denver TCU-61 User manual

in other languages

Related papers

Other documents