Honeywell Home RTH2300B User manual

Operating

Manual

RTH2300/RTH221 Series

Programmable Thermostat

69-2727ES-02

69-2727ES_A.indd 1 5/4/12 11:46 AM

Read and save these instructions.

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

® U.S. Registered Trademark. Patents pending.

This manual covers the following models:

RTH2300

RTH221

CAUTION: EQUIPMENT DAMAGE HAZARD.

To prevent possible compressor damage, do not operate cooling system when outdoor

temperature is below 50°F (10°C).

69-2727ES_A.indd 2 5/4/12 11:46 AM

RTH2300/RTH221

1 69-2727ES—02

About your new thermostat

Thermostat features .................................... 2

Thermostat is preset, ready to go ............... 3

Quick reference to controls ......................... 4

Quick reference to display ........................... 5

Programming & Operation

Set time and day ......................................... 6

Select system setting .................................. 7

Select fan setting ........................................8

Using program schedules .....................9–10

Adjust program schedule (RTH2300) .......11

Adjust program schedule (RTH221) .........12

Program schedule overrides ...............13–14

Compressor protection .............................. 15

Change Filter (RTH2300) ..........................16

Appendices

Battery replacement .................................. 17

Customer assistance ................................ 18

In case of difficulty .............................. 19–20

Limited warranty ........................................21

This thermostat is ready to go!

Your new thermostat is pre-programmed

and ready to go.

See page 10 to check settings.

Table of contents

69-2727ES_A.indd 1 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 2

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of reliable

service and easy-to-use, push-button climate control.

Features

• BacklitdisplayonRTH2300

• Displaysambient(measured)temperatureatalltimes

• One-touchaccesstosetpointtemperature

• Presetprogramsettings

• Temporaryandpermanentoverrideofschedule

• Built-incompressorprotection

69-2727ES_A.indd 2 5/4/12 11:46 AM

RTH2300/RTH221

3 69-2727ES—02

This thermostat is ready to go!

Your new thermostat is pre-programmed and ready to go. All you have to do is set the

time and day. Then check the settings below and change if needed:

1. Set time and day (required for proper operation) .............................. See page 6

2. Select system setting: Preset to Off ....................................To change, see page 7

3. Select fan setting: Preset to Auto .......................................To change, see page 8

4. Program schedules: Preset to energy-saving levels

while you’re at work or asleep........................................To change, see pages 9-12

ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and

manually adjust the temperature (see pages 13-14).

69-2727ES_A.indd 3 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 4

M33612

Heat Off Cool Auto On

Fan

Heat Off Cool

Auto On

Fan

Set

Hold

Run

Quick reference to controls

Temperature

adjustment (see

page 13-14)

Screen Lit for 12 seconds when you press any button.

Fan Switch (see page 8)

On: Fan runs continuously.

Auto: Fan runs only when heating or cooling system

is on.

Set: Press to set time/

day/schedule.

Hold: Press to override

programmed tempera-

ture control.

Run: Press to resume

program schedule.

System switch (see page 7)

• Heat: Heating system control.

• Off: All systems off.

• Cool: Cooling system control.

69-2727ES_A.indd 4 5/4/12 11:46 AM

RTH2300/RTH221

5 69-2727ES—02

M32701

We

Lo

Batt

Wake

Set

am

Heat

75

On

6

:

30

Quick reference to display screen

Low battery warning

(see page 16)

Setpoint indicator

Appears when the

setpoint temperature

is displayed.

Temperature

The ambient (measured)

temperature is normally

displayed. To view the

setpoint temperature,

presstheUporDown

button once. The setpoint

temperature will appear for

five seconds.

System status

Cool on: Cooling system is on.

Heat on: Heating system is on.

WhenCoolOnisflashing,compressorprotectionisengaged(seepage15).

Current day/time

(see page 6)

Current program period

Wake/Leave/Return/Sleep

(see pages 9-10)

69-2727ES_A.indd 5 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 6

Set

Hold

Run

Set Time

am

6

:

30

M33787

Set Day

We

Set

Hold

Run

M33788

Set the time and day

1. Press the SET button, then press s or t

to set the clock time.

2. Press the SET button, then press s or t

to select the day of the week.

3. Press RUN to save & exit.

Note: If the clock flashes, the thermostat will follow

your settings for the Monday “Wake” time period

until you reset the time and day.

Press SET, then adjust time.

Press SET, then select current day.

69-2727ES_A.indd 6 5/4/12 11:46 AM

RTH2300/RTH221

7 69-2727ES—02

M33612

Heat Off Cool Auto On

Fan

Heat Off Cool

Auto On

Fan

Set

Hold

Run

Select the system setting

The SYSTEM switch can be set to control

your heating or cooling system, depending

on the season.

• Cool: Cooling system control.

• Off: All systems are off.

• Heat: Heating system control.

Set SYSTEM switch to control the

heating or cooling system.

CAUTION: EQUIPMENT DAMAGE

HAZARD. To prevent possible

compressor damage, do not operate

cooling system when outdoor

temperature is below 50°F (10°C).

69-2727ES_A.indd 7 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 8

Select the fan setting

Set the FAN switch to Auto or On.

In “Auto” mode (the most commonly used

setting), the fan runs only when the heating

or cooling system is on.

Ifsetto“On,”thefanrunscontinuously.

Set FAN switch to choose whether the fan

runs continuously or only as needed.

M33612

Heat Off Cool Auto On

Fan

Heat Off Cool

Auto On

Fan

Set

Hold

Run

69-2727ES_A.indd 8 5/4/12 11:46 AM

RTH2300/RTH221

9 69-2727ES—02

Save money by setting program schedules

It’s easy to program your system for maximum energy savings. You can program four time

periods each day, with different settings for weekdays and weekends.

Set to the time you awaken and the temperature you want

during the morning, until you leave for the day.

Set to the time you leave home and the temperature you

want while you are away (usually an energy-saving level).

Set to the time you return home and the temperature you

want during the evening, until bedtime.

Set to the time you go to bed and the temperature you want

overnight (usually an energy-saving level).

WAKE

6:00 am

70

°

LEAVE

8:00 am

62

°

RETURN

6:00 pm

70

°

SLEEP

10:00 pm

62

°

69-2727ES_A.indd 9 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 10

About your new thermostatEnergy saving settings for maximum cost savings

This thermostat is pre-set to use energy saving program settings. We recommend these

settings, since they can reduce your heating/cooling expenses by as much as 33%. (See

next page to adjust times and temperatures of each time period.)

Wake

(6:00 am)

Leave

(8:00 am)

Return

(6:00 pm)

Sleep

(10:00 pm)

Cool (Mon-Fri)Heat (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)

70

°

78

°

70

°

78

°

62

°

85

°

62

°

85

°

70

°

78

°

70

°

78

°

62

°

82

°

62

°

82

°

69-2727ES_A.indd 10 5/4/12 11:46 AM

RTH2300/RTH221

11 69-2727ES—02

To adjust program schedules (RTH2300)

Set

Hold

Run

M33794

Mo Tu We Th Fr

Wake

Set Schedule

Set

am

75

6

:

30

1. Press SET until Set Schedule is displayed.

2. Press s or t to set your weekday Wake time

(Mo-Fr), then press SET.

3. Press s or t to set the temperature for this

time period, then press SET.

4. Set time and temperature for the next time

period (Leave). Repeat steps 2 and 3 for each

weekday time period.

5. Press SET to set weekend time periods (Sa &

Su), then press RUN to save & exit.

Note: Make sure the thermostat is set to the system

you want to program (Heat or Cool).

Press SET 3 times, then adjust time.

Press SET, then set desired temperature.

69-2727ES_A.indd 11 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 12

Set

Hold

Run

M33795

Mo Tu We Th Fr Sa Su

Wake

Set Schedule

Set

am

75

6

:

30

To adjust program schedules (RTH221)

1. Press SET until Set Schedule is displayed.

2. Press s or t to set your Wake time (Mo-Su),

then press SET.

3. Press s or t to set the temperature for this

time period, then press SET.

4. Set time and temperature for the next time

period (Leave). Repeat steps 2 and 3 for each

time period.

5. Press RUN to save & exit.

Note: Make sure the thermostat is set to the system

you want to program (Heat or Cool).

Press SET 3 times, then adjust time.

Press SET, then set desired temperature.

69-2727ES_A.indd 12 5/4/12 11:46 AM

RTH2300/RTH221

13 69-2727ES—02

About your new thermostat

Set

Hold

Run

M33796

Temporary

Set

am

70

6

:

30

Set

am

75

6

:

30

M33797

Set

Hold

Run

Program schedule override (temporary)

Press s or t to immediately adjust the

temperature. This will temporarily override

the temperature setting for the current time

period.

“Temporary” will appear on the display.

The new temperature will be maintained

only until the next programmed time period

begins (see page 9).

To cancel the temporary setting at any time,

press RUN.

Press to temporarily adjust temperature.

Press to cancel temporary setting and

resume program schedule.

Note: Make sure the thermostat is set to the

system you want to control (heat or cool).

69-2727ES_A.indd 13 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 14

About your new thermostat

Hold

Set

am

70

6

:

30

M33798

Set

Hold

Run

Set

am

75

6

:

30

M33797

Set

Hold

Run

Program schedule override (permanent)

Note: Make sure the thermostat is set to the system

you want to control (heat or cool).

Press to permanently adjust temperature.

Press HOLD to permanently adjust

the temperature. This will override the

temperature settings for all time periods.

The “Hold” feature turns off the program

schedule and allows you to adjust the

thermostat manually, as needed.

Whatever temperature you set will be

maintained 24 hours a day, until you

manually change it, or press RUN to cancel

“Hold” and resume the program schedule.

Press to cancel “Hold” setting and resume

program schedule.

69-2727ES_A.indd 14 5/4/12 11:46 AM

RTH2300/RTH221

15 69-2727ES—02

About your new thermostatBuilt-in compressor protection

This feature helps prevent damage to the com-

pressor in your air conditioning or heat pump

system.

Damagecanoccurifthecompressorisrestarted

too soon after shutdown. This feature forces the

compressor to wait 5 minutes before restarting.

Duringthewaittime,thedisplaywillflashthe

message CoolOn (or HeatOn if you have

a heat pump). When the safe wait time has

elapsed, the message stops flashing and the

compressor turns on.

Message flashes until safe restart

time has elapsed.

We

Wake

am

Cool

75

On

6

:

30

M32711

69-2727ES_A.indd 15 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 16

Change filter (RTH2300 only)

If the filter reminder is turned on during

installation, the words Change Filter will flash

on the screen when the filter needs to be

replaced.

After you replace the air filter, press and hold

the RUN button for 3 seconds to reset the alert.

Set

am

75

6

:

30

M33632

Set

Hold

Run

Change Filter – Press & Hold Run to Reset

69-2727ES_A.indd 16 5/4/12 11:46 AM

RTH2300/RTH221

17 69-2727ES—02

Battery replacement

Install two fresh AAA batteries when

Lo Batt flashes on the screen. Lo Batt

appears for 60 days before the batter-

ies are depleted.

Replace batteries once a year, or when

you will be away for more than a month.

Most settings are stored in non-volatile

(permanent)memory.Onlytheclock

and the day must be set after you

replace the batteries.

Pull at bottom to

remove thermostat

from wallplate.

Turn thermostat over,

insert fresh AAA alkaline

batteries, then reinstall

thermostat.

SettheSystemswitchtoOffbeforeremovingthe

batteries.Otherwise,theheating/coolingsystemcould

remain activated even when batteries are removed.

RTHXXXX

M32707

W/

Aux

Not

Used

Heat Off Cool Auto On

Fan

M33784

Heat Off Cool Auto On

Fan

Heat Off Cool

Auto On

Fan

Set

Hold

Run

69-2727ES_A.indd 17 5/4/12 11:46 AM

Operating Manual

69-2727ES—02 18

RTHXXXX

M32707

W/

Aux

Not

Used

Heat Off Cool Auto On

Fan

M33784

Heat Off Cool Auto On

Fan

Heat Off Cool

Auto On

Fan

Set

Hold

Run

Customer assistance

For assistance with this product, please visit

http://yourhome.honeywell.com.

OrcallHoneywellCustomerCaretoll-free

at 1-800-468-1502.

To save time, please note your model num-

ber and date code before calling.

Accessories

Turn thermostat over to

find model number and

date code.

Pull at bottom to

remove thermostat

from wallplate.

69-2727ES_A.indd 18 5/4/12 11:46 AM

Page is loading ...

Honeywell Home RTH2300B User manual

This manual is also suitable for

Honeywell Home RTH2300B User manual

in other languages

Related papers

Other documents