Craftsman 919.195413 Owner's manual

Owner's Manual

{CRAFTSMAN°{

Oil Lubricated

Single Stage

Horizontal Portable

AiR COMPRESSOR

Model No.

919.195413

= Safety Guidelines

= Assembly

= Operation

= Maintenance

= Troubleshooting

= Repair Parts

CAUTION: Read the Safety Guidelines

and All Instructions Carefully Before

Operating.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman

N000578 9/6/o7

WARRANTY ................................................ 2

SPECiFiCATiON CHART ...................................... 3

SAFETY GUiDELiNES ...................................... 3-9

GLOSSARY ............................................... 10

ACCESSORIES ............................................ 10

DUTY CYCLE .............................................. 10

ASSEMBLY ............................................ 11-12

iNSTALLATiON ......................................... 13-14

OPERATION ............................................ 15-17

MAINTENANCE ......................................... 18-20

SERVICE AND ADJUSTMENTS ............................ 21-23

STORAGE ................................................ 23

TROUBLESHOOTING GUIDE .............................. 24-27

REPAIR PARTS ......................................... 28-31

ESPAI_OL .............................................. 32-57

NOTES .................................................. 58

REPAIR PROTECTION AGREEMENTS ......................... 59

HOW TO ORDER REPAIR PARTS ...................... Back Cover

ONE YEAR FULL WARRANTY

If this product fails due to a defect in material or workmanship within one year

from the date of purchase, Sears will at its option repair or replace it free of

charge. Contact Sears at 1-800-4-MY-HOME ®to arrange for repair, or return it

to the place of purchase for replacement.

If this product is used for commercial or rental purposes, this warranty applies

for only ninety days from the date of purchase.

This warranty gives you specific legal rights and you may have other rights

which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

N000578 2-ENG

Model No. 919.195413

Running HP "1.8

Bore 2.875" (73.0 mm)

Stroke 2.0" (50.8 mm)

Voltage-Single Phase 120/240

Minimum Branch Circuit Requirement 15 amps

Fuse Type Time Delay

Air Tank Capacity 25 gallons (94.6 L)

Approximate Cut-in Pressure 120 PSi

Approximate Cut-out Pressure 150 PSi

SCFM @40 PSIG *7.4

SCFM @90 PSIG *5.8

* Tested per ISO 1217

Refer to Glossary for abbreviations.

This manual contains information that is important for you to know and under-

stand. This information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to these symbols.

_ Indicates an

imminently

hazardous situation which, if not

avoided, will result in death or

serious injury.

_ Indicates a

potentially

hazardous situation which, if not

avoided, could result in death or

serious inNu_13&

_ Indicates a

potentially

hazardous situation which, if not

avoided, _ result in minor or

moderate injury,.

_Used without the

safety alert symbol

indicates a potentially hazardous

situation which, if not avoided, may

result in pLo_pertydamage.

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

crystalline silica from bricks and cement and other masonry products

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, always wear

OSNA/MSHA/NIOSN approved, properly fitting face mask or respirator

when using such tools.

When using air tools, basic safety precautions should always be followed to

reduce the risk of of personal injury.

3- ENG N000578

This product contains chemicals, including lead, known to

the State of California to cause cancer, and birth defects

or other reproductive harm. Wash hands after handling.

Do not operate this unit until you read and _A

understand this instruction manual for safety,

operation and maintenance instructions.

SAVE THESE iNSTRUCTiONS

_ RiSK OF EXPLOSION OR FiRE

How to prevent it

• • Always operate the compressor in a

well ventilated area free of combus-

tible materials, gasoline, or solvent

vapors.

What can happen

It is normal for electrical contacts

within the motor and pressure

switch to spark.

• •

If electrical sparks from compressor

come into contact with flammable

vapors, they may ignite, causing fire

or explosion.

Restricting any of the compressor

ventilation openings will cause seri-

ous overheating and could cause

fire.

Unattended operation of this prod-

uct could result in personal injury

or property damage. To reduce the

risk of fire, do not allow the com-

pressor to operate unattended.

If spraying flammable materials,

locate compressor at least 20 feet

(6.1 m) away from spray area. An

additional length of air hose may be

required.

• Store flammable materials in a

secure location away from com-

pressor.

Never place objects against or on

top of compressor.

Operate compressor in an open

area at least 12" (30.5 cm) away

from any wall or obstruction that

would restrict the flow of fresh air to

the ventilation openings.

Operate compressor in a clean, dry

well ventilated area. Do not operate

unit indoors or in any confined area.

Always remain in attendance with

the product when it is operating.

Always turn off and unplug unit

when not in use.

Operate compressor in a clean, dry

well ventilated area. Do not oper-

ate unit in any confined area. Store

indoors.

N000578 4-ENG

__ RISK TO BREATHING (ASPHYXIATION)

What can happen How to prevent it

• The compressed air directly from • Air obtained directly from the com-

your compressor is not safe for pressor should never be used to

breathing. The air stream may con- supply air for human consumption.

tain carbon monoxide, toxic vapors, In order to use air produced by this

or solid particles from the air tank. compressor for breathing, suitable

Breathing these contaminants can filters and in-line safety equipment

cause serious injury or death, must be properly installed. In-line

filters and safety equipment used

in conjunction with the compressor

must be capable of treating air to all

applicable local and federal codes

prior to human consumption.

• Sprayed materials such as paint, • Work in an area with good cross

paint solvents, paint remover, insec- ventilation. Read and follow the

ticides, weed killers, may contain safety instructions provided on the

harmful vapors and poisons, label or safety data sheets for the

materials you are spraying. Always

use certified safety equipment:

OSHA/MSHA/NIOSH respiratory

protection designed for use with

your specific application.

__ RISK OF SERIOUS INJURY OR PROPERTY DAMAGE

WHEN TRANSPORTING COMPRESSOR

Oil can leak or spill and could

result in fire or breathing hazard;

serious injury or death can result.

oil leaks will damage carpet, paint

or other surfaces in vehicles or

trailers.

Always place compressor on a

protective mat when transport-

ing to protect against damage to

vehicle from leaks. Remove com-

pressor from vehicle immediately

upon arrival at your destination.

_ m D

__ RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and may be UM coded

[for units with air tanks greater than 6" (152.4 mm) diameter] according to ASME

Section VIII, Div. 1 rules. All pressure vessels should be inspected once every two

years. To find your state pressure vessels inspector, look under the Division of Labor

and Industries in the government section of a phone book.

The following conditions could lead to a weakening of the air tank, and result in a

violent air tank explosion:

5- ENG N000578

What can happen How to prevent it

• Failure to properly drain condensed • Drain air tank daily or after each

water from air tank, causing rust use. If air tank develops a leak,

and thinning of the steel air tank. replace it immediately with a new air

tank or replace the entire compres-

sor.

Modifications or attempted repairs

to the air tank.

Never drill into, weld, or make any

modifications to the air tank or its

attachments. Never attempt to

repair a damaged or leaking air

tank. Replace with a new air tank.

Unauthorized modifications to the • The air tank is designed to with-

safety valve or any other compo- stand specific operating pressures.

nents which control air tank pres- Never make adjustments or parts

sure. substitutions to alter the factory set

operating pressures.

Attachments & accessories:

• •

Exceeding the pressure rating of

air tools, spray guns, air operated

accessories, tires, and other inflata-

bles can cause them to explode or

fly apart, and could result in serious

injury.

Tires:

• Over inflationof tires could result in

serious injury and property damage.

Follow the equipment manufactur-

ers recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to inflate

small low pressure objects such as

children's toys, footballs, basket-

balls, etc.

Use a tire pressure gauge to check

the tires pressure before each use

and while inflating tires; see the tire

sidewall for the correct tire pressure.

NOTE: Air tanks, compressors and simi-

lar equipment used to inflate tires can fill

small tires similar to these very rapidly.

Adjust pressure regulator on air supply to

no more than the rating of the tire pres-

sure. Add air in small increments and

frequently use the tire gauge to prevent

over inflation.

,y,d, " D

Riskor ELECTRICALS.OCK

What can happen

Your air compressor is powered by

electricity. Like any other electrically

powered device, if it is not used

properly it may cause electric

shock.

How to prevent it

Never operate the compressor

outdoors when it is raining or in wet

conditions.

Never operate compressor with

protective covers removed or

damaged.

N000578 6-ENG

• Repairs attempted by unqualified

personnel can result in serious

injury or death by electrocution.

,, Electrical Grounding: Failure to ,,

provide adequate grounding to

this product could result in serious

injury or death from electrocution.

Refer to "Grounding Instructions"

paragraph in the Installation

section.

RiSKFROMfLYING

Any electrical wiring or repairs

required on this product should be

performed by authorized service

center personnel in accordance with

national and local electrical codes.

Make certain that the electrical

circuit to which the compressor

is connected provides proper

electrical grounding, correct voltage

and adequate fuse protection.

OBJECTS

What can happen

The compressed air stream can

cause soft tissue damage to

exposed skin and can propel dirt,

chips, loose particles, and small

objects at high speed, resulting in

property damage or personal injury.

How to prevent it

Always wear certified safety equip-

ment: ANSI Z87.1 eye protection

(CAN/CSA Z94.3) with side shields

when using the compressor.

Never point any nozzle or sprayer

toward any part of the body or at

other people or animals.

Always turn the compressor off

and bleed pressure from the air

hose and air tank before attempt-

ing maintenance, attaching tools or

accessories.

RiSKor.or SURFACES

What can happen

Touching exposed metal such as

the compressor head, engine head,

engine exhaust or outlet tubes, can

result in serious burns.

How to prevent it

Never touch any exposed metal

parts on compressor during or

immediately after operation.

Compressor will remain hot for

several minutes after operation.

Do not reach around protective

shrouds or attempt maintenance

until unit has been allowed to cool.

7- ENG N000578

RiSKFROMMOVINGPARTS

What can happen

Moving parts such as the pulley, fly-

wheel, and belt can cause serious

injury if they come into contact with

you or your clothing.

• Attempting to operate compressor

with damaged or missing parts or

attempting to repair compressor

with protective shrouds removed

can expose you to moving parts

and can result in serious injury.

How to prevent it

Never operate the compressor with

guards or covers which are dam-

aged or removed.

Keep your hair, clothing, and gloves

away from moving parts. Loose

clothes, jewelry, or long hair can be

caught in moving parts.

Air vents may cover moving parts

and should be avoided as well.

Any repairs required on this product

should be performed by authorized

service center personnel.

[__ RiSK OF UNSAFE OPERATION

What can happen

Unsafe operation of your air com-

pressor could lead to serious injury

or death to you or others.

How to prevent it

Review and understand all instruc-

tions and warnings in this manual.

Become familiar with the operation

and controls of the air compressor.

Keep operating area clear of all per-

sons, pets, and obstacles.

Keep children away from the air

compressor at all times.

Do not operate the product when

fatigued or under the influence of

alcohol or drugs. Stay alert at all

times.

Never defeat the safety features of

this product.

Equip area of operation with a fire

extinguisher.

= Do not operate machine with miss-

ing, broken, or unauthorized parts.

N000578 8-ENG

__ RiSK OF INJURY FROM LiFTiNG

How to prevent it

• • The compressor is too heavy to be

lifted by one person. Obtain assis-

tance from others before lifting.

What can happen

Serious injury can result from

attempting to lift too heavy an

object.

RISK FROM NOISE

What can happen How to prevent it

Under some conditions and dura- • Always wear certified safety equip-

tion of use, noise from this product ment: ANSI S12.6 (S3.19) hearing

may contribute to hearing loss. protection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

9- ENG N000578

Become familiar with these terms

before operating the unit.

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per min-

ute; a unit of measure of air delivery.

PSIG: Pounds per square inch gauge;

a unit of measure of pressure.

Code Certification: Products that

bear one or more of the following

marks: UL, CUL, ETL, CETL, have

been evaluated by ©SHA certified

independent safety laboratories and

meet the applicable Standards for

Safety.

Cut=In Pressure: While the motor

is off, air tank pressure drops as you

continue to use your accessory. When

the tank pressure drops to a certain

low level the motor will restart auto-

matically. The low pressure at which

the motor automatically restarts is

called "cut-in" pressure.

Cut=Out Pressure: When an air com-

pressor is turned on and begins to

run, air pressure in the air tank begins

to build. It builds to a certain high

pressure before the motor automati-

cally shuts off, protecting your air tank

from pressure higher than its capacity.

The high pressure at which the motor

shuts off is called "cut-out" pressure.

Branch Circuit: Circuit carrying elec-

tricity from electrical panel to outlet.

This unit is capable of powering the following Accessories. The accessories are

available through the current Power and Hand Tool Catalog or full-line Sears

stores.

Accessories

• In Line Filter

Tire Air Chuck

Quick Connector Sets (various

sizes)

Air Pressure Regulators

Oil Fog Lubricators

Air Hose:l/4" (6.4 mm), 3/8"

(9.5 mm) or 1/2" (12.7 mm) inside

diameter in various lengths

Refer to the selection chart located

on the unit to select the tools this unit

is capable of powering.

This air compressor pump is capable

of running continuously. However,

to prolong the life of your air com-

pressor, it is recommended that a

50%-75% average duty cycle be

maintained; that is, the air compres-

sor pump should not run more than

30-45 minutes in any given hour.

N000578 10-ENG

CONTENTS OF CARTON

1 - Air Compressor

2- Wheels

2 - Shoulder Bolts, 3/8-16

2 - Hex Nuts, 3/8-16

1- Handle

1 - Handle Grip

2 - Cap Screws

2 - 1/4-20 Hex Nuts

2 - Retainer Clips

2 - Flat Washers

2 - Rubber Bumpers

2 - Screws, 1/4-20 x 3/4" (19 ram)

TOOLS REQUIRED FOR

ASSEMBLY

1 - 9/16" (14 ram) socket or open

end wrench

1 - 1/2" (13 ram) socket or open end

wrench

3.

Open End

Handle

Slowly push the open ends of

the handle onto both tabs at the

same time. Continue pushing the

handle into the saddle until the

holes on the side of the saddle

and handle are in line.

UNPACKING

Remove unit from carton and discard

all packaging. NOTE: Save all parts

bags.

TO iNSTALL HANDLE

The wheels and

handle do not

provide adequate clearance,

stability, or support for pulling the

unit up and down stairs or steps.

The unit must be lifted or pushed

up a ramp. Do not lift the unit by the

manifold assembly; the unit could

be damaged.

4. Guide the straight end of each

retaining clip through the saddle

hole and both handle holes.

1.

2.

To make installation easier, sub-

merge handle grip into warm

soapy water. Remove handle grip

from soapy water and slide onto

handle.

Insert the open ends of the

handle under the saddle. Before

attaching handle, you may have

to pull the open ends of the han-

dle apart so they fit tightly against

the side of the saddle. Looking in

from the open end of the saddle,

position the handle toward the

two bent tabs, on the inside walls

of the saddle.

11- ENG N000578

5. Rotate each retaining clip clock-

wise and press down until it

snaps into place over the handle.

6. If the handle has excessive

movement, it is improperly

installed. Check the following.

A. Are both tabs inside the

handle (Step #3)?

B. Does each clip pass through

both the saddle and handle

(Step #4)?

TO ASSEMBLE WHEELS

It will be necessary

to brace or support

one side of the air compressor when

installing the wheels because the

compressor will have a tendency to

tip.

1. Attach wheels with shoulder bolts

and nuts as shown.

2. Tighten securely. NOTE: The air

compressor will sit level if the

wheels are properly installed.

The wheels and

handle do not

provide adequate clearance, stability

or support for pulling the unit up and

down stairs or steps. The unit must

be lifted, or pushed up a ramp.

ASSEMBLE RUBBER FEET

1. Attach rubber feet with the

screws, washers and nuts pro-

vided as shown in figure below.

2. Tighten securely.

Nut

Wheel

OIL FOR PUMP

This compressor was

shipped with oil in

the pump crankcase. Check oil before

operating air compressor, see Check

Oil under Maintenance.

N000578 12-ENG

LOCATION OF THE AIR

COMPRESSOR

• Locate the air compressor in a

clean, dry, and well ventilated

area.

• Place on a solid surface to pre-

vent rocking or tipping.

The air compressor should be

located at least 12" (30.5 cm)

away from the wall or other

obstructions that will interfere

with the flow of air.

The air filter must be kept clear of

obstructions which could reduce

air flow to the air compressor.

The air compressor requires

fresh air flow for proper cool-

ing. DO NOT ALLOW THE

COMPRESSOR TO GET WET.

GROUNDING iNSTRUCTiONS

RISK OF

-- ELECTRICAL

SHOCK. In the event of a short

circuit, grounding reduces the risk

of shock by providing an escape

wire for the electric current. This

air compressor must be properly

grounded.

The portable air compressor is

equipped with a cord having a ground-

ing wire with an appropriate grounding

plug (see following illustrations). The

plug must be used with an outlet that

has been installed and grounded in

accordance with all local codes and

ordinances.

1. The cord set and plug with this

unit contains a grounding pin.

This plug MUST be used with a

grounded outlet.

IMPORTANT: The outlet being used

must be installed and grounded in

accordance with all local codes and

ordinances.

2.

Make sure the outlet being used

has the same configuration as the

grounded plug. DO NOT USE AN

ADAPTER. See illustration.

Plug

Grounding Pin

Grounded

Outlets

3.

4.

Inspect the plug and cord before

each use. Do not use if there are

signs of damage.

If these grounding instructions are

not completely understood, or if in

doubt as to whether the compres-

sor is properly grounded, have the

installation checked by a qualified

electrician.

RISK OF

-- ELECTRICAL

SHOCK. IMPROPER GROUNDING

CAN RESULT iN ELECTRICAL

SHOCK.

Do not modify the plug provided. If

it does not fit the available outlet, a

correct outlet should be installed by

a qualified electrician.

Repairs to the cord set or plug

MUST be made by a qualified

electrician.

EXTENSION CORDS

Using extension cords is not

recommended. The use of extension

cords will cause voltage to drop

resulting in power loss to the motor

and overheating.

13- ENG N000578

Instead of using an extension cord,

increase the working reach of the

air hose by attaching another length

of hose to its end. Attach additional

lengths of hose as needed.

If an extension cord must be used, be

sure it is:

• a 3-wire extension cord that has a

3-blade grounding plug, and a 3-

slot receptacle that will accept the

plug on the product

in good condition

no longer than 50 feet

12 gauge (AWG) or larger. (Wire

size increases as gauge number

decreases. 10 AWG and 8 AWG

may also be used. DO NOT USE

14 OR 16 AWG.)

VOLTAGE AND CiRCUiT

PROTECTION

Refer to the specification chart for the

voltage and minimum branch circuit

requirements.

Risk of Unsafe

Operation. Certain

air compressors can be operated

on a 15 amp circuit if the following

conditions are met.

1. Voltage supply to circuit must

comply with the National

Electrical Code.

2. Circuit is not used to supply any

other electrical needs.

3. Extension cords comply with

specifications.

4. Circuit is equipped with a 15 amp

circuit breaker or 15 amp time

delay fuse. NOTE: If compressor

is connected to a circuit protect-

ed by fuses, use only time delay

fuses. Time delay fuses should be

marked "D" in Canada and "T" in

the US.

If any of the above conditions cannot

be met, or if operation of the compres-

sor repeatedly causes interruption

of the power, it may be necessary to

operate it from a 20 amp circuit. It is

not necessary to change the cord set.

120/240 DUAL VOLTAGE MOTOR

This model has a dual voltage motor,

120 and 240 volt. it is wired for 120

volt but can be converted to 240 volt

operation, instructions for connecting

the motor for operation at 240 volt can

be found printed on the label attached

to the side of the motor.

When converting to

240V operation, the

attached three-prong 120V cord

assembly must be replaced with a

three-pronged 240V cord assembly

(K-0080} that can be purchased

through a Sears Service Center.

120 Volt Plug 240 Volt Plug

N000578 14-ENG

KNOW YOUR AIR COMPRESSOR

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING

YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with

the location of various controls and adjustments. Save this manual for future

reference.

Auto(I)/Off(O) Switch

Regulator

Auto(I)/Off(O) Switch: Turn this switch

"Auto" to provide automatic power

to the pressure switch and "Off" to

remove power at the end of each use.

Pressure Switch: The pressure switch

automatically starts the motor when

the air tank pressure drops below the

factory set "cut-in" pressure. The pres-

sure switch stops the motor when the

air tank pressure reaches the factory

set "cut-out" pressure.

Safety Valve: If the pressure switch

does not shut off the air compressor

at its "cut-out" pressure setting, the

safety valve will protect against high

pressure by "popping out" at its fac-

tory set pressure (slightly higher than

the pressure switch "cut-out" setting).

Outlet Pressure Gauge: The outlet

pressure gauge indicates the air pres-

sure available at the outlet side of the

regulator. This pressure is controlled by

the regulator and is always less than or

equal to the tank pressure.

Tank Pressure Gauge: The tank pres-

sure gauge indicates the reserve air

pressure in the tank.

Regulator: Controls the air pressure

shown on the outlet pressure gauge.

Pull the knob out and turn clockwise

to increase pressure and counterclock-

wise to decrease pressure. When the

desired pressure is reached push knob

in to lock in place.

Universal Quick-Connect Body: The

universal quick-connect body accepts

the three most popular styles of quick-

connect plugs: Industrial, automotive

(Tru-flate), and ARC. One hand push-

to-connect operation makes connec-

tions simple and easy.

Drain Valve: The

drain valve is

located at the

base of the air

tank and is used

Valve

to drain conden-

sation at the end of each use.

Cooling System (not shown): This

compressor contains an advanced

design cooling system. At the heart of

this cooling system is an engineered

fan. It is perfectly normal for this fan to

blow air through the vent holes in large

amounts. You know that the cooling

system is working when air is being

expelled.

15- ENG

N000578

Air Compressor Pump (not shown):

Compresses air into the air tank.

Working air is not available until the

compressor has raised the air tank

pressure above that required at the air

outlet.

Check Valve: When the air compres-

sor is operating, the check valve is

"open", allowing compressed air to

enter the air tank. When the air com-

pressor reaches "cut-out" pressure,

the check valve "closes", allowing air

pressure to remain inside the air tank.

To restart:

1. Place the

Auto/Off

lever in the

"Off" pos-

tion.

2. Allow the

motor to

cool.

3. Depress the

red reset button on the motor.

4. Place the Auto/Off lever in the

"Auto" postion to restart the

motor.

HOW TO USE YOUR UNIT

How to Stop

1. Set the Auto/Off switch to "Off".

Before Starting

E__ o not operate this

unit until you read

and understand this instruction

manual for safety, operation and

maintenance instructions.

Pressure Release Valve: The pres-

sure release valve, located on the side

of the pressure switch, is designed to

automatically release compressed air

from the compressor head and the

outlet tube when the air compressor

reaches "cut-out" pressure or is shut

off. The pressure release valve allows

the motor to restart freely. When the

motor stops running, air will be heard

escaping from this valve for a few

seconds. No air should be heard

leaking when the motor is running or

after unit reaches "cut-out" pressure.

Air intake Filter (not shown) This

filter is designed to clean air coming

into the pump. This filter must always

be clean and ventilation openings free

from obstructions. See Maintenance.

Motor: This motor has a manual ther-

mal overload protector. If the motor

overheats for any reason, the overload

protector will shut off the motor. The

motor must be allowed to cool down

before restarting.

Break=in Procedure

N000578

Risk of Unsafe

Operation. Serious

damage may result if the following

break=in instructions are not closely

followed.

16- ENG

This procedure is required before the

air compressor is put into service and

when the check valve or a complete

compressor pump has been replaced.

1. Make sure the Auto/Off switch is

in the "Off" position.

2. Check oil level in pump. See "Oil"

paragraph in the Maintenance

section for instructions.

NOTE: If quick connect is installed,

pull coupler back until it clicks to

prevent air from escaping through the

quick connect.

3. Plug the power cord into the cor-

rect branch circuit receptacle.

(Refer to Voltage and Circuit

Protection paragraph in the

Installation section of this manual.)

4. Open the drain valve (counter-

clockwise) fully to permit air to

escape and prevent air pressure

build up in the air tank during the

break-in period.

5. MovetheAuto/Offswitchto"Auto"

position.Thecompressorwillstart.

6. Runthecompressorfor20min-

utes.Makesurethedrainvalve

isopenandthereisminimalair

pressurebuild-upintank.

7. After20minutes,closethedrain

valvebyturningclockwise.Theair

receiverwillfillto"cut-out"pres-

sureandthemotorwillstop.

Thecompressorisnowreadyforuse.

BeforeEachStart=Up

1. SettheAuto/Offswitchto"Off".

2. Pullregulatorknobout,turn

counterclockwiseuntilitstops.

Pushknobintolockinplace.

3. Attachhoseandaccessories.

NOTE:Thehoseoraccessorywill

requireaquickconnectplugifthe

airoutletisequipped with a quick

connect socket.

_Risk of unsafe

__ operation. Firmly

grasp air hose in hand when

installing or disconnecting to

prevent hose whip.

_Risk of unsafe

__ operation. Do not

use damaged or worn accessories.

Risk of Bursting.

Too much air

pressure causes a hazardous risk of

bursting. Check the manufacturer's

maximum pressure rating for air

tools and accessories. The regulator

outlet pressure must never exceed

the maximum pressure rating.

Risk of unsafe

operation.

Compressed air from the unit may

contain water condensation and

oil mist. Do not spray unfiltered air

at an item that could be damaged

by moisture. Some air tools and

accessories may require filtered

air. Read the instructions for the air

tools and accessories.

Bow to Start

1. Set the Auto/Off switch to "Auto"

and allow tank pressure to build.

Motor will stop when tank pressure

reaches "cut-out" pressure.

2. Pull the regulator knob out and

turn clockwise to increase pres-

sure. When the desired pressure

is reached push knob in to lock in

place.

_lf any unusual

__ noise or vibration

is noticed, stop the compressor

immediately and have it checked by

a trained service technician.

The compressor is ready for use.

17- ENG N000578

CUSTOMER RESPONSiBiLiTiES

Before iDaily Every Every Every Every Yearly

each ior 8 40 100 160

use after hours ihours hours hours

each

use

Check Safety Valve •

Drain Tank

Oil Leaks

Check Pump Oil

Change Pump Oil

Unusual Noise and/

or Vibration

Air Filter o 1

Drive Belt-Condition

Motor Pulley/Flywheel

alignment

Air compressor

pump intake and

exhaust valves

Inspect air lines and *

fittings for leaks

Head Bolts - Check the torques of the head bolts after the first five hours of operation.

1- more frequent in dusty or humid conditions

_Risk of Unsafe

__ Operation. Unit

cycles automatically when power

is on. When servicing, you may

be exposed to voltage sources,

compressed air, or moving parts.

Before servicing unit unplug or

disconnect electrical supply to

the air compressor, bleed tank

of pressure, and allow the air

compressor to cool.

To ensure efficient operation and lon-

ger life of the air compressor, a routine

maintenance schedule should be pre-

pared and followed. The above routine

maintenance schedule is geared to an

air compressor in a normal working

environment operating on a daily basis.

If necessary, the schedule should be

modified to suit the conditions under

which your air compressor is used.

The modifications will depend upon

the hours of operation and the work-

ing environment. Compressors in an

extremely dirty and/or hostile environ-

ment will require a greater frequency of

all maintenance checks.

NOTE: See Operation section for the

location of controls.

TO CHECK SAFETY VALVE

E__ Risk of Bursting.

If the safety valve

does not work properly, over=

pressurization may occur, causing

air tank rupture or an explosion.

E__ Risk from Flying

__ Objects. Always

wear certified safety equipment:

ANSi Z87.1 eye protection (CAN/

CSA Z94.3) with side shields.

N000578 18-ENG

Before starting compressor, pull the

ring on the safety valve to make sure

that the safety valve operates freely. If

the valve is stuck or does not operate

smoothly, it must be replaced with the

same type of valve.

TO DRAIN TANK

Risk of Unsafe

Operation. Risk

from noise. Air tanks contain high

pressure air. Keep face and other

body parts away from outlet of

drain. Use ANSI Z87.1 eye protection

(CAN/CSA Z94.3) when draining as

debris can be kicked up into face.

Use ear protection [(ANSi S12.6

(S3.19} hearing protection] as air

flow noise is loud when draining.

1. Set the Auto/Off switch to "Off".

2. Pull the regulator knob out and

turn clockwise to set the outlet

pressure to zero.

3. Remove the air tool or accessory.

4. Pull ring on safety valve allowing

air to bleed from the tank until

tank pressure is approximately 20

PSI. Release safety valve ring.

5. Drain water from air tank by open-

ing drain valve on bottom of tank.

Risk of Bursting.

Water will

condense in the air tank. If not

drained, water will corrode and

weaken the air tank causing a risk

of air tank rupture.

Risk of Property

Damage. Drain

water from air tank may contain oil

and rust which can cause stains.

6. After the water has been drained,

close the drain valve. The air com-

pressor can now be stored.

NOTE: If drain valve is plugged,

release all air pressure. The valve can

then be removed, cleaned, the rein-

stalled.

OIL

This compressor

was shipped with

oil in the pump crankcase. Check

oil before operating air compressor,

see Check Oil under Maintenance.

Risk of Bursting.

Drain tank to release

air pressure before removing the oil

fill cap or oil drain plug.

Use air

compressor oil

only. Multi-weight automotive

engine oils like lOW30 should

not be use in air compressors.

They leave carbon deposits on

critical components, thus reducing

performance and compressor life.

Checking

1. Place unit on a level surface.

2. Remove the oil fill plug (A). The oil

level should be even with the top

of the fill hole and no lower than 6

threads from the top of fill hole.

2. If needed, slowly add oil until it

reaches the top of fill hole.

NOTE: Use 30W compressor oil or

a heavy duty SAE 30W, non-deter-

gent, SF grade or better oil DO NOT

use multi-weight automotive engine

oils, they will reduce compressor life.

Under extreme winter condition use

SAE-10 weight oil.

Changing

1. Place unit on a level surface.

2. Remove the oil fill plug (A).

3. Remove the oil drain plug (B) and

drain oil into a suitable container.

4. Replace the oil drain plug (B) and

tighten secure.

19- ENG N000578

NOTE: Use 30W compressor oil or a

heavy duty SAE 30W, non-detergent,

SF grade or better oil DO NOT use

multi-weight automotive engine oils,

they will reduce compressor life. Under

extreme winter condition use SAE-10

weight oil.

5. Slowly fill crankcase to the top of

the fill hole. NOTE: Crankcase oil

capacity is approximately 16 fluid

ounces (0.5 L).

6. Replace oil fill plug (A) and tighten

securely.

AIR FILTER iNSPECTiON AND

REPLACEMENT

Risk of Burns.

-- Compressor head

and cylinder sleeve are very hot. Do

not touch. Allow compressor to cool

prior to servicing.

A dirty air filter will not allow the com-

pressor to operate at full capacity.

Keep the air filter clean at all times.

1. Remove the air filter cover.

2. Remove the air filter from filter

cover.

iMPORTANT: Do not operate the

compressor with the air filter removed.

3. Place new air filter into filter cover.

Refer to the "Repair Parts" for the

correct part number.

4. Replace air filter cover and lock

into place.

MOTOR PULLEY/FLYWHEEL

ALIGNMENT

NOTE: Once the motor pulley has

been moved from its factory set loca-

tion, the grooves of the flywheel and

pulley must be aligned to within 1/16"

(1.6 mm) to prevent excessive belt

wear.

The air compressor flywheel and motor

pulley must be in-line (in the same

plane) within 1/16" (1.6 mm) to assure

belt retention within flywheel belt

grooves. To check alignment, perform

the following steps:

1. Unplug air compressor from

power source.

2.

3.

4.

Remove belt guard.

Place a straightedge against the

outside of the flywheel and the

motor drive pulley.

Measure the distance between

the edge of the belt and the

straightedge at points A1 and A2

in figure. The difference between

measurements should be no more

than 1/16" (1.6 mm).

_EL: MOTOR PULLEY

AI_A2(MEASUREBi STBAiGNT

B1_ B_(V_SUAL) EDG_

5. If the difference is greater or less

than 1/16" (1.6 mm) loosen the

set screw holding the motor drive

pulley to the shaft and adjust the

pulley's position on the shaft until

the A1 and A2 measurements

are within 1/16" (1.6 mm) of each

other.

6. Torque the motor drive pulley set

screw to 70-80 in.-Ibs.

7. Visually inspect the motor drive

pulley to verify that it is perpen-

dicular to the drive motor shaft.

Points B1 and B2 of Figure should

appear to be equal. If they are

not, loosen the setscrew of the

motor drive pulley and equalize B1

and B2, using care not to disturb

the belt alignment performed in

step 2.

8. Retighten the motor drive pulley

setscrew to 70-80 in.-Ibs.

9. Reinstall belt guard.

AiR COMPRESSOR PUMP

iNTAKE AND EXHAUST VALVES

Once a year have a Trained Service

Technician check the air compressor

pump intake and exhaust valves.

N000578 20-ENG

Page is loading ...

Craftsman 919.195413 Owner's manual

Craftsman 919.195413 Owner's manual

in other languages

Related papers

Other documents