Animal Factory Amplification MAN-EM2 User manual

Brand
Animal Factory Amplification
Model
MAN-EM2
Type
User manual

Animal Factory Amplification MAN-EM2 is a eurorack module that blends a distortion circuit with a state-variable filter, giving you a wide range of sound-sculpting possibilities. Its three filter bands (low-pass, band-pass and high-pass) can be modulated with CV signals to create dynamic and evolving soundscapes. With its built-in VCA and blend control, you can smoothly transition between dry and effected signals, making it an excellent tool for adding texture and character to your music.

Animal Factory Amplification MAN-EM2 is a eurorack module that blends a distortion circuit with a state-variable filter, giving you a wide range of sound-sculpting possibilities. Its three filter bands (low-pass, band-pass and high-pass) can be modulated with CV signals to create dynamic and evolving soundscapes. With its built-in VCA and blend control, you can smoothly transition between dry and effected signals, making it an excellent tool for adding texture and character to your music.

VOLUME: Controls the overall
volume of the distortion circuit.
LPF BPF HPF
SOFT HARD
GAIN VOLUME
MIDS
BLEND
DYNAMICS
CV
FREQUENCY
CV
Q
CV
FM
CV
DYNAMICS
IN
FREQUENCY
IN
Q
IN
FM
IN
INPUT DRY OUT WET OUT MIX OUT
DYNAMICS CV: The attenuator
controls the amount of CV
signal that affects the dynamics
of the circuit.
FREQUENCY CV: Controls the
amount of CV modulating the
frequency. If no input is
connected to FREQUENCY IN,
this knob can be used to sweep
the frequency.
Q CV: Controls the amount of
CV that modulates the Q
amount for each filter band.
The knob is normalized to
control the Q amount if nothing
is connected to Q IN.
FM CV: Controls the amount
of CV signal that affects the
self-FM circuit. The knob is
normalized to control the
amount of FM if nothing is
connected to FM IN.
BLEND: Controls the balance
between the dry and wet signal
on the mix out.
SOFT SWITCH: The middle
position applies no clipping,
the top and bottom positions
give two different flavors of
“soft” clipping. Soft doesn’t
mean nice and fluffy though.
HARD SWITCH: The middle
position applies no clipping,
the top and bottom positions
give two different flavors of
“hard” clipping (a bit like
limiting).
MIDS SWITCH: Sets the amount
of bass cut prior to the drive
circuit.
UNDERSTANDING AND CARING FOR YOUR ANIMAL
PIT VIPER EURORACK MODULE
USER MANUAL
Congratulations!
You are now a proud human to a Pit Viper Eurorack Module.
In this edition, we retained all the venom of the original... and added a little
more, in the form of a nasty filter with individual output levels!
UPPER KNOBS
LOWER KNOBS
SWITCHES
CONTROLS
LPF: The knob controls the
amount of the filtered low-pass
signal post drive.
BPF: The knob controls the
amount of the filtered
band-pass signal post drive.
HPF: The knob controls the
amount of the filtered
high-pass signal post drive.
GAIN: Controls the amount
the clipping circuit is engaged.
AFA PIT VIPER EURORACK MANUAL (V2, 2022 ) UPDATED APRIL 12 2022 PAGE 1/2
DYNAMICS IN: CV signal
applied to the input controls
the dynamics of the distor-
tion circuit. IMPORTANT:
This effect is best heard if
GAIN is turned all the way
down, and becomes less
useful at higher settings.
FREQUENCY IN: CV signal
applied to the input controls
the cutoff point of each filter
band.
Q IN: CV signal applied to
the input controls the Q
amount of each filter band.
FM IN: CV signal to the
input controls the bias
applied to the FM circuitry
of the band-pass filter.
INPUT: Input connector that
takes in signal to be
processed.
DRY OUT: Sends out the
unprocessed signal as is.
WET OUT: The output of the
distorted circuit pre-filter.
MIX OUT: The output of the
distorted signal with the
filtered output.
AUDIO I/O
GAIN
BLEND
VOLUME
SVF
FILTER
CIRCUIT
DRIVE
CIRCUIT
IN
DRY
OUT
DIST
OUT
MIX
OUT
FREQ
CV
FREQUENCY
CONTROL
RESONANCE
CONTROL
LP
BP
HP
VCA
RES
CV
FM
AMT
DYN
CV
Subscribe to our newsletter for updates regarding expansion modules and manual updates...
[email protected]
TECHNICAL SPECIFICATIONSENVIRONMENT
EXPANSION HEADER
CONTACT/QUESTIONS/COMMENTS/FEEDBACK
Power Draw:
+12V: 44mA
-12V: 43mA
Size: 12HP
Skiff friendly
Do not dispose of any part of this module in household
waste.
Electronics must be disposed of safely according to the
electronics disposal norms in your country.
This module was constructed using lead-free solder and
observes compliance with the RoHS directive.
All parts of our packaging are designed to use minimal or
no plastic.
Use the box and the velvet bag to keep other things safe.
CV I/O
SIGNAL FLOW
AFA PITVIPER EURORACK MANUAL (V2, 2022 ) UPDATED APRIL 12 2022 PAGE 2/2
  • Page 1 1
  • Page 2 2

Animal Factory Amplification MAN-EM2 User manual

Brand
Animal Factory Amplification
Model
MAN-EM2
Type
User manual

Animal Factory Amplification MAN-EM2 is a eurorack module that blends a distortion circuit with a state-variable filter, giving you a wide range of sound-sculpting possibilities. Its three filter bands (low-pass, band-pass and high-pass) can be modulated with CV signals to create dynamic and evolving soundscapes. With its built-in VCA and blend control, you can smoothly transition between dry and effected signals, making it an excellent tool for adding texture and character to your music.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents