Schiit Lyr User manual

FUSION ARCHITECTURE HEADPHONE AMP & PREAMP

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

The following is required by the roughly 9,542

government agencies and regulations we have to

comply with. If you have some common sense, they

should seem pretty straightforward. In any case, read these

instructions before proceeding farther, follow all instructions,

and heed all warnings. Or else!

1. If you don’t know how to install audio devices, get a

qualied professional to help.

2. Never use this device near water, and clean only with a

dry cloth.

3. Assure adequate ventilation, do not block any ventilation

openings, or place near heat sources.

4. Use only the supplied power cord or suitable replacement.

Route cords away from trac areas and protect them from

being pinched. Unplug the cord from the outlet if the apparatus

is unused for a long period of time.

5. To prevent electric shock, do not use the plug with an

extension cord, receptacle, or outlet unless blades can be

fully inserted.

6. Refer all servicing to qualied service personnel. Service is

required when the device has been damaged, including cord or

plug damage, liquid has been spilled or objects have fallen into

the device, the device has been exposed to rain or moisture,

does not operate normally, or has been dropped.

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO

RAIN OR MOISTURE.

No Tube? It’s easy. Just plug in Lyr+ and turn it

on. The mode and gain lights will ash for 30-45

seconds, then Lyr+ will enable its output.

If you aren’t going to use a tube for a while, you

can cover the hole with the supplied Tube Cover.

Yes Tube? It’s still easy. Just follow these steps:

1. Before plugging in, insert the tube. Carefully

align the key in the tube base to the notch in the

tube socket.

2. Ensure tube is well-seated.

Push down rmly until the tube

is seated on the tube socket.

3. Plug in and turn on. The

tube will glow after a few sec-

onds. As before, the mode and gain lights will

ash while Lyr+ self-checks, then it will unmute.

4. Connect your system. Plug in up to two

sources, plug in your headphones, and, if you

like, use the preamp outputs for a speaker amp

or sub. And enjoy!

Replacing or Swapping Tubes

1. Turn off and unplug. Wait for the tube to cool.

2. Carefully extract the tube by gently rocking it

back and forth and pulling upwards.

3. Carefully insert the replacement tube. Align

the key to the notch and press down rmly until

the tube is seated.

4. Plug the Lyr+ back in and turn it on.

NOTCH

Lyr+ is the most advanced desktop-sized

product we’ve ever produced. Combining all-new

Fusion Architecture™ that lets you use tube or

solid state gain, relay ladder volume control,

advanced microprocessor protection, and re-

mote control, it’s a technological tour de force.

Now, you can roll all the tubes you want...and

still have a great solid-state amp whenever you

want. We hope you enjoy your time with Lyr+—

we certainly had plenty of fun developing it!

INTRODUCTION

WHAT’S IN THE BOX

(1) Lyr+

(1) Lyr+ Tube Cover

(1) Remote Control

(1) Power cord

(1) 6SN7 type tube (if you ordered it with Lyr+)

GETTING STARTED

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

5 Gain/Mode Select. Push this button to toggle

between low and high gain modes. When chang-

ing gain, the gain light will ash briey

If you don’t have the remote handy, you can

also press and hold the Gain/Mode switch for

4 seconds or more to change operating modes.

When you release the button, the mode light

will ash for up to 40 seconds during the mode

change.

6 Headphone Jack. Plug your headphones in

here, using a standard 1/4” TRS plug.

1 Input Select. Press this button to toggle be-

tween the two inputs. To the right of the button,

the selected input lights up.

2 Preamp Output Enable. Push the button to en-

able and disable the preamp output. The light to

the right indicates when the preamp outs are on.

3 Volume Control. Turn up till the music sounds

good, but before your ears turn to taffy.

4 Mode Indicator. When this light is on, Lyr+ is

using its internal solid-state gain stage. When it’s

off, then it’s running tube gain. Remember, you

can’t run tube gain without a tube!

1 Input. Press this button to select the input you want to

listen to. If you skip the input, keep pressing—it cycles back

around.

2 Tube/MOSFET Mode. When you have a tube installed, you

can switch back and forth between tube and MOSFET gain

modes by pressing this button. The Mode light will ash for

up to 40 seconds while changing modes.If you don’t have a

tube installed, this button won’t do anything.

3 Gain. Toggle between low and high gain with this button.

The Gain light will ash briey when changing modes. We

recommend turning down the volume before switching to

high gain, as it is signicantly higher than low gain.

4 Mute. Press to mute Lyr+—headphone, preamp outs,

everything goes off.

5 Preamp Output Enable/Disable. Press to enable or disable

the preamp outputs.

6 Volume Up/Down. Press the up arrow to turn volume up,

press the down arrow to turn it down. Simple!

Note: To change the remote battery, push the front off the remote using a

paperclip through the back hole, then replace with the same size and type.

REMOTE CONTROLCONTROLS

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

1 2

Why do the Gain and Mode lights

both ash after I turn Lyr+ on?

The two lights ash to let you know Lyr+ is

coming up to its correct operating point. Lyr+

monitors operational parameters as it is turning

on, and only connects the output when everything

is ne. This can take up to 40 seconds.

When I switch gain, the lights ash again?

The gain light ashes after you change gain,

while Lyr’s microprocessor protection system

mutes the output, and monitors operational

points until all is settled and ready to go.

I get a ashing light when switching mode too.

Also normal. Lyr+ will ash the mode light while

it is stabilizing when changing modes. This can

take up to 40 seconds.

What’s with all the clicking noises

when I turn the volume?

That’s the sound of the mechanical relays in the

relay-switched stepped attenuator. Also normal.

3 On-Off Switch. Up is on. Down is off. Pretty

simple, right?

4 AC Input. Plug the power cord in here. Plug the

other end into an outlet of the correct voltage.

Trying to run a 115V product on 230V will blow the

fuse and generally make for a bad, bad day.

1 RCA Inputs.

Connect up to 2 inputs to Lyr+ using RCA cables.

The inputs are conveniently numbered “1” and

“2” to match the front panel indicators. Select the

input you want to listen to using the front panel

button or the remote control.

2 Preamp Output.

Optionally, connect this output to a separate

power amp (or subwoofer) using RCA cables. You

can switch on and off the preamp output using

the front panel button or the remote control.

012345678

115VAC 30W

ASSY IN USA

VOLUME

INPUT PREOUT

MUTE

GAIN

MODE

FAQCONNECTIONS

1 2 3 4

What kind of tubes can I use in Lyr+?

Use only 6SN7-type tubes, including 6N8S,

5692, and (of course) 6SN7.

Can I leave Lyr+ on all the time?

You can, but it would be best to do it with no

tube inserted. The tube heater is on all the

time, and leaving it powered on all the time will

shorten the tube lifespan.

The Lyr+ clicks and I don’t hear any music,

then it clicks back on, over and over again.

Lyr+ is running into protection. This can mean

a shorted headphone cable or an incompat-

ible cable, like a TRRS cable with a bad 1/4”

converter. Try Lyr+ with a different headphone,

check you headphone cables, and, if you want

to use a TRRS headphone, we sell a connection

kit here: schiit.com/trrs

It doesn’t turn on, what do I do?

Plug it in to a different AC socket. Ensure you

are not currently in a blackout. Then email us if

it still doesn’t work.

WARRANTY

Schiit Audio warrants to the original purchaser that the product shall be free from defects in material and workmanship

for ve (5) years from the date of purchase. Exceptions: tubes and remote controls. Tubes are covered by a 90-day limited

warranty with the same terms. Remote controls are covered by a 1-year warranty with the same terms. If a defect covered

by this warranty occurs during this warranty period, Schiit Audio will repair the defective product, free of charge. Date

of purchase will be based on customer-submitted receipts, otherwise date of manufacturing will be used to determine

warranty period.

If you believe you need warranty service, CONTACT US rst. There may be a simple solution to your problem. Schiit

Audio products sent back to us without a RETURN AUTHORIZATION (RA) will be returned to the sender without repair. To

WARRANTY LIMITATIONS

THIS WARRANTY SHALL NOT APPLY IF THIS PRODUCT: (a) IS MODIFIED OR TAMPERED WITH; (b) IS DAMAGED BY

NEGLIGENCE, ACCIDENT, UNREASONABLE USE, COFFEE, OR BY OTHER CAUSES UNRELATED TO DEFECTIVE

MATERIALS OR WORKMANSHIP; OR (c) HAS HAD THE SERIAL NUMBER ALTERED, DEFACED OR REMOVED.

ANY APPLICABLE IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE HEREBY LIMITED IN DURATION TO THE WARRANTY PERIOD (5 YEARS). IN NO EVENT

SHALL SCHIIT AUDIO BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE BREACH OF

ANY IMPLIED OR EXPRESS WARRANTIES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS OR EXCLUSION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATIONS MAY

NOT APPLY TO YOU.

This warranty gives you specic legal rights. You may also have other rights which vary from state to state or province

to province.

SCHIIT.COM

[email protected]

Application for Council Directives 72/23/EEC

Conformity declared for EN60065, EN50082-1

Schiit Lyr User manual

Related papers

Other documents