Kistler 2519A Owner's manual

Instruction

Manual

Data Evaluation and

Reference Manual

Transient Recorder

Type 2519A…

Software

TR Control

2519A_002-607e-10.12

Instruction

Manual

Data Evaluation and

Reference Manual

Transient Recorder

Type 2519A…

Software

TR Control

2519A_002-607e-10.12

Foreword

2519A_002-607e-10.12 Page 1

Foreword

Thank you for choosing a Kistler quality product

characterized by technical innovation, precision and long

life.

Information in this document is subject to change without

notice. Kistler reserves the right to change or improve its

products and make changes in the content without

obligation to notify any person or organization of such

changes or improvements.

expressly provided herein, no part of this manual may be

reproduced for any purpose without the express prior

written consent of Kistler Group.

Kistler Group

Eulachstrasse 22

8408 Winterthur

Switzerland

Tel. +41 52 224 11 11

Fax +41 52 224 14 14

info@kistler.com

www.kistler.com

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 2 2519A_002-607e-10.12

Content

1. Introduction ................................................................................................................................... 3

1.1 Disposal Instructions for Electrical and Electronic Equipment ................................................ 4

1.2 Software Upgrades and Updates .......................................................................................... 4

2. Data Evaluation .............................................................................................................................. 5

3. Reference Instructions .................................................................................................................. 21

3.1 TR 2519: Block Diagram ..................................................................................................... 21

3.2 TR 2519: Technical Specifications ....................................................................................... 22

3.3 TR 2519: Description of Front and Rear Panel .................................................................... 25

3.3.1 Front Panel ............................................................................................................ 25

3.3.2 Rear Panel ............................................................................................................. 26

3.4 Detailed Description of All Functions of Control Program ................................................... 27

3.4.1 Main TR 2519 Control Window ............................................................................ 27

Menu File ............................................................................................... 28 3.4.1.1

Menu Edit .............................................................................................. 38 3.4.1.2

Menu Calibration ................................................................................... 39 3.4.1.3

Menu Measurement .............................................................................. 43 3.4.1.4

3.4.1.4.1 Target Background ................................................................................................ 48

Real Diameter of Hits and Shot Numbers in Target Picture .................... 50 3.4.1.5

Menu Graphs and Computing ............................................................... 51 3.4.1.6

Menu Select ........................................................................................... 66 3.4.1.7

Menu Settings ........................................................................................ 67 3.4.1.8

Menu Help ............................................................................................. 72 3.4.1.9

3.4.2 TR 2519: Panel of Virtual TR 2519 ........................................................................ 73

Total pages 78

Introduction

2519A_002-607e-10.12 Page 3

1. Introduction

Please take the time to thoroughly read this instruction

manual. It will help you with the installation, maintenance,

and use of this product.

To the extent permitted by law Kistler does not accept any

liability if this instruction manual is not followed or

products other than those listed under Accessories are

used.

Kistler offers a wide range of products for use in measuring

technology:

 Piezoelectric sensors for measuring force, torque, strain,

pressure, acceleration, shock, vibration and acoustic-

emission

 Strain gage sensor systems for measuring force and

torque

 Piezoresistive pressure sensors and transmitters

 Signal conditioners, indicators and calibrators

 Electronic control and monitoring systems as well as

software for specific measurement applications

 Data transmission modules (telemetry)

Kistler also develops and produces measuring solutions for

the application fields of engines, vehicles, manufacturing,

plastics and biomechanics sectors.

Our product and application brochures will provide you

with an overview of our product range. Detailed data

sheets are available for almost all products.

If you need additional help beyond what can be found

either on-line or in this manual, please contact Kistler's

extensive support organization.

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 4 2519A_002-607e-10.12

1.1 Disposal Instructions for Electrical and Electronic Equipment

Do not discard old electronic instruments in municipal

trash. For disposal at end of life, please return this

product to an authorized local electronic waste disposal

service or contact the nearest Kistler Instrument sales

office for return instructions.

1.2 Software Upgrades and Updates

Kistler may from time to time supply upgrades or updates

for embedded software. Such upgrades or updates must

always be installed.

Kistler declines any liability whatsoever for any direct or

consequential damage caused by products running on

embedded software which has not been upgraded or

updated with the latest software supplied.

Data Evaluation

2519A_002-607e-10.12 Page 5

- measurement of time intervals (between each curves)

- measurement of velocity (by use of known base)

- independent selection of rising or falling edges

- independent setting of threshold levels

- time filter for elimination of shockwaves

(between two edges)

Time Interval & Velocity

THRESHOLD

LEVEL

t

2. Data Evaluation

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 6 2519A_002-607e-10.12

- measurement of time intervals (between each curves)

- measurement of velocity (by use of known base)

- independent selection of first zero-crossing after

crossing of the threshold level from left to right

or from right to left direction

- time filter for elimination of shockwaves

(between two zero-crossings)

Time Interval & Velocity

THRESHOLD

LEVEL

t

Data Evaluation

2519A_002-607e-10.12 Page 7

- measurement of time intervals (between each curves)

- measurement of velocity (by use of known base)

- program determines time interval between rising edges

of start integral curve and stop integral curve

- especially designed for measurement of velocity by use

of centre of gravity (pellets etc.)

()by use of integral

Time Interval & Velocity

THRESHOLD

LEVEL

t

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 8 2519A_002-607e-10.12

- measurement of curve maximum (Pmax etc.)

- measurement of time position of maximum

(time interval between accelerometer and Pmax)

- filter for noise supression

(and time position of maximum)

Maximum Value of Curve

Pmax

t

Data Evaluation

2519A_002-607e-10.12 Page 9

- measurement of integral (area) of curve between

two cursors

(between two cursors)

Integral of Curve

AREA

t

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 10 2519A_002-607e-10.12

- measurement of integral (area) of curve between

two events (see picture) : start of integration is derived

from accelerometer signal (yellow curve), stop

is derived from muzzle sensor (green curve)

- independent selection of rising or falling edges

- time filter for noise supression

(between two events)

Integral of Curve

AREA

t

Data Evaluation

2519A_002-607e-10.12 Page 11

- measurement of derivation (slope, dy/dt) of curve

between two cursors

(between two cursors)

Derivation of Curve

dy

dt

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 12 2519A_002-607e-10.12

- measurement of derivation (slope, dy/dt) of curve

between two levels (in % of curve maximum)

- each level is adjustable in range 0-100%

- designed for easy measurement of curve slew rate

(between two levels)

Derivation of Curve

10% Pmax

90% Pmax

dy

dt Pmax

Data Evaluation

2519A_002-607e-10.12 Page 13

- measurement of Rate Of Fire between all

consecutive shots

- measurement of velocity (by use of known base)

for all shots

- independent selection of rising or falling edges

- independent setting of threshold levels

- time filter for elimination of shockwaves

(between two consecutive shots)

Rate Of Fire

THRESHOLD

LEVEL

ti

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 14 2519A_002-607e-10.12

- measurement of hit position and target velocity

by use of electronic target system DTS01/02

- ratio of intervals t1 and t2 determines X (or Y)

coordinate of hit

- independent selection of rising or falling edges,

threshold levels and shockwave filters for X and

for Y coordinate

(2x DTS01/02)

Target System

THRESHOLD

LEVEL

t2

t1

Data Evaluation

2519A_002-607e-10.12 Page 15

- measurement of function value of curve Y=f(X)

for entered fixed value of X

(Y = f(X) for fixed value of X)

Function Value of Curve

Y= (X)f

X

Data Evaluation and Reference Manual Transient Recorder Type 2519A…

Page 16 2519A_002-607e-10.12

- measurement of function value of curve Y=f(X)

at event X (rising or falling edge of impulse)

(Y = f(X) )at event

Function Value of Curve

Y= (X)f

X

Data Evaluation

2519A_002-607e-10.12 Page 17

-

testing of shape of curve (Pass / Fail)

unlimited number of masks with save/load option

(PASS / FAIL testing)

Limit Mask

MIN

MAX

Page is loading ...

Kistler 2519A Owner's manual

Kistler 2519A Owner's manual

Related papers

Other documents