Peerless PAP-UNV-W User manual

Brand: Peerless

Model: PAP-UNV-W

Category: Projector mounts

Type: User manual

This manual is also suitable for

PAP-UNV

ISSUED: 09-12-05 SHEET #: 055-9438-7 11-05-09

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.

1 of 2

Note: Actual parts may appear slightly different than illustrated.

IMPORTANT! Read entire instruction sheet

before you start installation and assembly.

Installation and Assembly - Spider™ Universal Adapter Plate Models: PAP UNV, PAP UNV-S,

PAP UNV-W

Description Qty. PAP UNV PAP UNV-S PAP UNV-W

AA adapter plate (without connection block) 1 055-1867 055-4867 055-2867

adapter plate (with connection block) 1 055-1879 055-4879 055-2879

BB M3 x 8 mm serrated washer head socket pin screw (not shown) 4 510-1004 510-2004 510-2004

CC M4 x 10 mm serrated washer head socket pin screw (not shown) 4 510-1060 510-2060 510-2060

DD M5 x 10 mm serrated washer head socket pin screw (not shown) 4 510-1126 510-2063 510-2063

EE M6 x 10 mm serrated washer head socket pin screw (not shown) 4 510-1066 510-2066 510-2066

FF 4 mm security allen wrench (for PAP only) 1 560-9646 560-9646 560-9646

GG 2 mm security allen wrench 1 560-1097 560-1097 560-1097

HH washer 4 540-1025 540-2025 540-2025

Parts List

Before you start check the parts list below to

make sure all of the parts shown are included.

Patent No. D597,582 To be used with PJF, PJF2, PRS and RTR Series

• It is the responsibility of the installer to ensure that the

projector is properly ventilated. Spacers are provided to

raise the mount off the projector surface.

CAUTION

• Installer must verify that the ceiling will safely support

four times the combined weight of all attached equip-

ment and hardware.

WARNING

Configuration without Connection Block (For use with PJF

and PJF2 models)

Configuration with Connection Block (Connection block is

provided with PRS and RTR model)

This product is intended for use with UL

Listed products and must be installed by a

qualified professional installer.

ISSUED: 09-12-05 SHEET #: 055-9438-7 11-05-09

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.

2 of 2

Peerless is a registered trademark of Peerless Industries, Inc.

Spider is a trademark of Peerless Industries, Inc.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Mounting

hole

Generic Projector

Place projector upside down. Locate adapter plate (AA) with notch facing forward as close to projector center of

gravity as possible without covering any mounting holes. Loosen channels, and if there are only three mounting

holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting

holes as shown below. Important: If projector does not have at least three mounting holes, do not use this

adapter plate.

Note: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a

mounting hole.

Note: Once channels are in position retighten fasteners.

*Notch indicates front of projector.

Note: The projector you are installing may differ in appearance from the sample illustrated below.

Attach adapter plate (AA) to projector using one screw (BB, CC, DD, or EE) for each channel as shown below.

Tighten all screws, while keeping the center of gravity. Be sure that adapter plate (AA) is straight. Adjust the feet

of the channels to keep the adapter plate level. Tighten all screws with 4 mm security allen wrench (FF) or wrench

provided with projector mount, while keeping the center of gravity. If M3 screws are used, tighten using 2 mm

security allen wrench (GG).

Note: Projectors will require different size screws for mounting. Use a combination of screws (BB, CC, DD, or EE)

and foot adjustment that will result in channels of adapter plate (AA) fitting tightly against projector. Important: In

order to properly engage the threads in the mounting holes, the screw must be turned at least 3 full turns.

Note: If using screw (BB), place washer (HH) between screw (BB) and foot of channel.

Foot of Channel

• It is the responsibility of the installer to ensure that the

projector is properly ventilated. Feet of channels are

used to raise the mount off the projector surface.

CAUTION

BB,CC,DD,

or EE

Peerless PAP-UNV-W User manual

Brand: Peerless

Model: PAP-UNV-W

Category: Projector mounts

Type: User manual

This manual is also suitable for

PAP-UNV

Download PDF

report

Peerless PAP-UNV-W User manual

This manual is also suitable for

Peerless PAP-UNV-W User manual

Related papers

Other documents