DuraMax TRAILER BRAKE CONTROL WIRING User manual

Type
User manual

DuraMax TRAILER BRAKE CONTROL WIRING allows you to connect electric trailer brakes to your vehicle, providing additional stopping power when towing. Easily adjust the trailer brake gain to suit different loads and conditions, ensuring smooth and controlled braking. The system supports up to 4 axles with electric trailer brakes (8 brake magnets). Monitor the trailer brake output and gain settings conveniently through the Driver Information Center display.

DuraMax TRAILER BRAKE CONTROL WIRING allows you to connect electric trailer brakes to your vehicle, providing additional stopping power when towing. Easily adjust the trailer brake gain to suit different loads and conditions, ensuring smooth and controlled braking. The system supports up to 4 axles with electric trailer brakes (8 brake magnets). Monitor the trailer brake output and gain settings conveniently through the Driver Information Center display.

Home » duramax » duramax TRAILER BRAKE CONTROL WIRING SCHEMATICS User Manual
Contents
1 duramax TRAILER BRAKE CONTROL WIRING
SCHEMATICS
2 Documents / Resources
2.1 References
3 Related Posts
duramax TRAILER BRAKE CONTROL WIRING SCHEMATICS
duramax TRAILER BRAKE CONTROL WIRING SCHEMATICS
User Manual
Manuals+ User Manuals Simplified.
YMMS: 2011 Chevrolet Silverado 2500 HD
Engine: 6.6L Eng
VIN:
WIRING SCHEMATICS > TRAILER BRAKE CONTROL WIRING SCHEMATICS
Fig 1: Trailer Brake Control Wiring Schematic (JL1 Except 10 Series)
Fig 2: Trailer Brake Control Wiring Schematic (JL1 Except 10 Series)
DESCRIPTION AND OPERATION > TRAILER BRAKE CONTROLS DESCRIPTION AND OPERATION
Some trucks less than 3900 Kg (8600 lb) GVW with a gasoline engine may be equipped with a Trailer Brake
Control Module (TBCM) or a combination Fuel Pump/Trailer Brake Control Module (FTCM) system for electric
trailer brakes. Some trucks greater than or equal to 3900 Kg (8600 lb) GVW may be equipped with a integrated
Trailer Brake Control Module (TBCM) system for electric trailer brakes. The power output to the trailer brakes is
based on the amount of brake pressure being applied in the vehicle’s brake system. The available power output to
the trailer brakes can be adjusted to a wide range of trailering situations.
NOTE: Connecting a trailer that is not compatible with the trailer brake system may result in reduced or complete
loss of trailer braking. There may be an increase in stopping distance or trailer instability which could result in
personal injury or damage to your vehicle, trailer, or other property. An aftermarket controller may be available for
use with trailers with surge, air or electric-over-hydraulic trailer brake systems. To determine the type of brakes on
your trailer and the availability of controllers, check with your trailer manufacturer or dealer. Do not power-up an
aftermarket controller with the factory brake controller at the same time.
The vehicle is equipped with the following trailer braking components:
Manual Trailer Brake Apply
Trailer Gain Adjustment
Trailer Brake Control Panel
Trailer Brake Driver Information Center Display
The Trailer Brake Control Module (TBCM) or a combination Fuel Pump/Trailer Brake Control Module
(FTCM) can support up to a maximum of 4 axles with electric trailer brakes (8 brake magnets).
DESCRIPTION AND OPERATION > TRAILER BRAKE CONTROLS DESCRIPTION AND OPERATION >
SERVICE TRAILER BRAKE SYSTEM
This message will be displayed when there is a problem with the trailer brake control system. If this message
persists over multiple ignition cycles there is a concern with the trailer brake system. Take your vehicle to an
authorized GM dealer to have the trailer brake system diagnosed and repaired.
DESCRIPTION AND OPERATION > TRAILER BRAKE CONTROLS DESCRIPTION AND OPERATION >
TRAILER GAIN AND OUTPUT DISPLAY
This display menu can be accessed by scrolling through the Driver Information Center menu, or any time the
trailer gain +/- button is depressed, or the manual trailer brake apply lever is actuated. The trailer gain display is 0
to 10 in 0.5 step increments, and indicates the current user setting of the trailer output gain. The trailer output is 0
to 10 bars in 1 bar increments, and indicates the output power provided to the trailer brakes, relative to the gain
setting.
Documents / Resources
duramax TRAILER BRAKE CONTROL WIRING SCHEMATICS [pdf] User Manual
TRAILER BRAKE CONTROL WIRING, BRAKE CONTROL WIRING SCHEMATICS, BRAKE C
ONTROL WIRING
References
Printer Friendly View
Manuals+,
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

DuraMax TRAILER BRAKE CONTROL WIRING User manual

Type
User manual

DuraMax TRAILER BRAKE CONTROL WIRING allows you to connect electric trailer brakes to your vehicle, providing additional stopping power when towing. Easily adjust the trailer brake gain to suit different loads and conditions, ensuring smooth and controlled braking. The system supports up to 4 axles with electric trailer brakes (8 brake magnets). Monitor the trailer brake output and gain settings conveniently through the Driver Information Center display.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI