Page is loading ...
Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v032m
SKU: STAND-V032M
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A (x1)
Arm
B (x1)
Pole
C (x1)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D (x1)
Grommet
Base Plate
E (x6)
Wire Clip
F (x1)
Cable Clip
G (x1)
Pole Cover
H (x5)
Rubber Pad
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
I (x1)
Support Plate
J (x1)
3mm Allen Key
M-A (x8)
M4X12
M-B (x8)
M5x12
M-C (X8)
D5 Washer
L (x1)
6mm Allen Key
K (x1)
5mm Allen Key
3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
OPTION A: Clamp Installation
Screw pole (B) into clamp base
(C), and tighten the two set
screws with Allen key (J). Apply
feet (H) to bottom of clamp
base (C). Attach cover (G) and
cable clip (F) to base and pole
assembly. Secure clamp to desk
using hand bolt.
OPTION B: Grommet Base Installation
Remove hand bolt from clamp (C) by
first removing Phillips screw from the
top of the bolt, then remove the plate
and unscrew the bolt. Apply feet (H)
to bottom of grommet base (D). Screw
pole (B) into base, and tighten the two
set screws with Allen key (J). Attach
cover (G) and cable clip (F) to base and
pole assembly. Mount grommet base
to desk using grommet plate (I) and
previously removed hand bolt.
10-8 8m
m
H
F
G
C
B
J
C
D
H
1
0
-
8
8
m
m
F
G
I
J
B
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
4
STEP 2
Slide arms (A) onto pole, and tighten with Allen key (K).
STEP 3
Attach cable clips (E) to arms.
A
K
5
STEP 4
Insert (M-A or M-B) screws and (M-C) washers into top two holes of monitor, leaving 3mm of thread
visible. Hang monitor over open slots in VESA plate, and secure with two more screws and washers in
bottom holes.
STEP 5
Adjust monitor tilt support using Allen key (L).
M- A
M- B
M- C
1
2
3m m
M- A
M- B
M- C
+45°
-45°
L
6
STEP 6
Store Allen keys (K,L) in cable clip for quick access.
K
L
7
STEP 7
Turn bolts behind VESA plates using Allen key (K) to adjust height and align monitors. Manage cables.
K
360°
360°
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/