www.tefal.com
IXEO QT10XX
EN
1800147399
2
Important safety recommendations
• Please read these instructions carefully before rst use. This
appliance has been designed for domestic and indoor use
only. Any commercial use, inappropriate use or failure to
comply with the instructions, the manufacturer accepts no
responsibility and the guarantee will not apply.
• Never unplug the appliance by pulling the power cord. Always
unplug your appliance:
− before lling the water tank.
− before cleaning the appliance,
− after each use.
• The appliance must be used and placed on a at, stable, heat-
resistant surface. When you place the appliance on its stand,
ensure that the surface on which the stand is placed is stable.
• This appliance is not intended to be used by persons (including
children) with reduced or impaired physical, sensory or
mental capabilities or persons lacking appropriate knowledge
or experience, unless a person responsible for their safety
provides either supervision or appropriate instructions
concerning use of the appliance prior to its use.
• Children should be supervised to ensure they do not play
with the appliance.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
• Keep the iron and its cords out of reach of children less than
8 years of age when it is in use or cooling down.
• The surfaces of your appliance can reach very high
temperatures when functioning, which may cause burns.
Do not touch the hot surfaces of the appliance (accessible
metal parts and plastic parts adjacent to the metallic parts)
until the appliance is completely cool.
• Never leave the appliance unattended when it is connected to
the mains. Before storing the appliance, once it is unplugged,
please wait until it has cooled down (around 1 hour).
3
• The appliance must not be used if it has been dropped, if it
has any visible damage, if it leaks, or if it functions abnormally
in any way. Do not attempt to dismantle your appliance:
have it examined at an Approved Service Centre to avoid any
danger.
• Check the electrical power cord and water connection cord
for signs of wear or damage prior to use. If the electrical
power cord or the water connection cord is damaged, it must
be replaced by an Approved Service Centre to avoid any
danger.
• Care should be taken when using the appliance due to the
emission of steam.
• For lling, cleaning and descaling your appliance, please refer
to the instruction for use.
• For your safety, this appliance conforms to all applicable regulations (Low Voltage Directive, Electromagnetic Compatibility,
Environment, etc).
• Your appliance is an electrical appliance: it must be used under normal conditions of use. It is designed for domestic use only.
• Always plug your appliance:
- into a mains circuit with voltage between 220 V and 240 V,
- into an earthed electrical socket.
Connecting to the wrong voltage may cause irreparable damage to the appliance and will invalidate your guarantee. If you are
using a mains extension lead, ensure that it is correctly rated (16A) with an earth, and is fully extended.
• Completely unwind the power cord before plugging into an earthed socket.
• The soleplate of your appliance can reach extremely high temperatures, and can cause burns: do not touch them. Never touch
the electrical power and water connection cords with the soleplate of the appliance.
• Your appliance emits steam, which can cause burns. Always handle the appliance with care, especially when ironing/steaming
vertically. Never direct the steam towards people or animals.
• Never immerse your appliance in water or any other liquid. Never place it under a running tap.
• The plug must be removed from the socket-outlet before the water reservoir is lled with water.
• Unplug the the appliance during lling and cleaning.
• Be careful when assembling the appliance and when adjusting the board to avoid ngers being caught in the mechanisms.
• The use of accessory attachments other than those provided by the manufacturer is not recommended and may result in re,
electric shock or personal injury.
Before rst use
When you rst use the iron, some smoke or a harmless odour may be produced or there may be a small discharge of
particles. This will not aect the use of the appliance and will disappear quickly.
- Not for drinking
- Keep out of the reach of children
- Dispose with household refuse
- Keep in cool dry place
What water to use?
Your appliance has been designed to use untreated tap water. However, the self-clean function must be performed
regularly on the steam chamber to remove limescale.
Do not use pure demineralised or pure distilled water, water from clothes dryers, scented or softened water, rain
water, ltered, bottled or boiled water, water from refrigerators, batteries or air conditioners as these may damage
the appliance. These types of water contain organic waste, mineral elements that become concentrated when heated
and cause spitting, brown staining, leaking or premature wear on your appliance. If your water is very hard, mix 50%
untreated tap water with 50% distilled water (available in hardware stores).
PLEASE RETAIN THIS INSTRUCTION
BOOKLET FOR FUTURE REFERENCE
Environment protection rst !
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
4
On rst use, fumes and odour may come from the appliance. They do not aect the use
of the appliance and disappear quickly.
On rst use, small particles may come from the iron. These are part of the production
process and do not aect yourself or your garments. They disappear quickly.
The appliance must be used and placed on a at, stable, heat-resistant surface. When
you place the appliance on its stand, ensure that the surface on which the stand is
placed is stable.
— What kind of water to use?
Your iron has been designed to use tap water. If your water is very hard, mix 50%
untreated tap water and 50% destilled water.
IMPORTANT
Do not use pure demineralised or pure distilled water, water from clothes
dryers, scented or softened water, rain water, ltered, bottled or boiled
water, water from refrigerators, batteries or air conditioners as these may
damage the appliance. These types of water contain organic waste, mineral
elements that become concentrated when heated and cause spitting, brown
staining, leaking or premature wear on your appliance. If your water is very
hard, mix 50% untreated tap water with 50% distilled water (available in
hardware stores).
IMPORTANT
Never use your appliance board with a classic iron or a steam generator.
Only use your appliance iron.
EN
Before rst use
5
1
Product presentation
Product
1
2
3
5
6
7
4
8
EN
1. Hanger hook
2. Tilting board
3. Iron rest
4. Iron
5. Collapsible body
6. Height adjusters
7. Steam unit
8. Steam hose
6
Iron and steam unit
1
2
3
6
4
5
7
8
EN
1. Iron soleplate
2. Steam trigger
3. Water tank
4. Anti calc light
indicator
5. On/O button
6. Power cord
7. Anti-Calc cartridge
8. Cartridge
compartment
7
2
First use
Incline the board
Move the board to the horizontal position
1
1
2
2
3
3
EN
Put your hands on each side of the board, raise it vertically , and tilt it back until inclined
position.
EN
Put your hands on each side of the board, raise it vertically , and tilt it back until horizontal
position.
8
Adjust the height
Orientation of the iron rest
1
1
2
2
3
3
EN
When adjusting the height of the board make sure you hold on to it as
there is a risk that it may fall.
EN
At the horizontal position, unlock the height adjusters. Raise or lower the board until the
desired position. Lock the pole lockers.
EN
The iron rest is on a swivel and can be adjusted to suit the user.
9
Fill the water tank
1
3
2
4
3
First use of the appliance
EN
Ensure that the anti-calc is installed before switching on the appliance.
To install the anti-calc cartridges, please refer to assembly instructions.
EN
Unplug the appliance.
EN
Fill the water tank.
EN
Unlock & remove the water tank.
EN
Replace the water tank and lock it.
10
Turning on the iron
1 2 3
45s 1m30s
ON
4
Ironing & Steaming
Shirt
I
II
EN
Put the iron on the iron
rest.
EN
In the inclined position, put the shirt on the board to iron
the back and the front.
EN
Plug in the appliance
and switch it on. Wait for
45 seconds.
EN
Press the trigger for
approximately 1 minute 30
seconds until steam comes
out.
Steam pump may produce
some noise during this stage,
it is completely normal.
EN
Use the board at the
horizontal position to
iron the details.
11
Trousers
EN
Use the board in the horizontal position
to iron the details.
EN
On the inclined board, hang the
trousers to iron the legs.
NO
EN
Never iron or steam directly on a garment being worn
by someone.
12
* Depending on model
Accessories
*
— Fabric brush
1h
OFF
I
II
1 2
EN
Use the hanger hook to iron/steam a
garment placed on a hanger.
EN
Before you remove or attach the brush,
switch o the appliance and allow it to
cool down for 1 hour.
EN
Put the steam brush on the iron soleplate.
This accessory helps to open the garment
bres for better steam penetration.
EN
Use the clips to hold a garment on the
board.
13
Use the portable steam unit
1 2 3
45 s
ON
I
II
Steam boost
x 2
EN
Remove the steam unit
o its base. Remove the
iron and the iron rest.
EN
Position the iron and its
iron rest on the steam
unit.
EN
Press the steam trigger two times to
activate the steam boost.
EN
Move around with the
appliance. Plug in and
switch on the appliance,
and wait 45seconds before
using the iron.
EN
Be careful of of heat and steam when using the appliance.
14
1
1
2
2
3
3
8 min
38 min
OFF
Auto-o
EN
After 8 minutes of inactivity, the steam unit will change to stand by mode.
EN
After 38 minutes of inactivity, the steam unit will switch o automatically.
15
5
Cleaning
6
Storing
OFF
OFF
1
1
2
2
3
3
1h
1h
I
II
NO
I
II
EN
Switch o the appliance.
Wait 1 hour to allow it to
cool down completely.
EN
Switch o the appliance.
Wait 1 hour to allow it to
cool down completely.
EN
Clean the soleplate with
a damp soft cloth or
sponge.
EN
Empty the water tank.
EN
Never use abrasive
products or surfaces to
clean the soleplate.
EN
Move the iron rest to the
back of the board.
16
7
Anti-calc
4 5
ANTI
CALC
EN
When the anti-calc cartridge comes to its end of life, the
anti-calc light ashes.
EN
Tilt up the board to the vertical position.
EN
Transportation advice: To move your appliance, use the poles as grasping area.
EN
Ensuring the water tank is empty, lean
the appliance backwards if necessary, in
order to move and store it away.
17
OFF
1
4
2
5
3
6
1h
I
II
II
I
x2
EN
Switch o the appliance.
Wait 1 hour to allow it to
cool down completely.
EN
Remove the anti-calc
cartridge.
EN
Remove the water tank.
EN
Discard of the old
anti-calc cartridge.
EN
Turn the steam unit over
and open the 2 locking
tabs.
EN
Open the new anti-calc
cartridge.
18
7
10 11 12
8 9
x2
CLICK
EN
Remove the stoppers.
EN
Turn the steam unit
back over so that it is the
right way up.
EN
Insert the anti-calc
cartridge into the steam
unit.
EN
Fill the water tank.
EN
Close the 2 locking tabs
of the anti-calc cartridge
compartment.
EN
Replace the water tank,
and lock it.
19
12 13 14
45 s
ON
I
II
1 min 30 s
EN
Put the iron and the
steam unit on the base.
EN
Plug in and switch on
the appliance. Wait for
45 seconds.
EN
Press the trigger for
approximately 1 minute
and 30 seconds until
steam comes out.
20
Problems with your appliance?
PROBLEM POSSIBLE CAUSES SOLUTIONS
Brown water is dripping from
the soleplate and soiling your
clothes.
You are using chemical descaling
products.
Do not put any descaling product into
the water tank.
You are not using the right water. Perform a self-clean and consult the
"What water to use?" section.
The soleplate is dirty or brown
and may soil clothes.
The soleplate has not been cleaned. Clean the soleplate as indicated in the
user guide.
Your appliance produces little
or no steam.
Your appliance has a build up of limescale. Please refer to anti-calc section.
The soleplate is scratched or
damaged.
You have positioned your iron at on the
metallic iron support.
You have cleaned your soleplate with an
abrasive cloth or steel wool.
Always place your iron in the support
base. Clean the soleplate as indicated in
the user guide.
Your soleplate emits particles. Limescale is starting to build up on your
soleplate.
Perform a self-clean .
Water drips from the holes in
the soleplate.
You are using steam while the iron is not
hot enough.
Wait until the thermostat light goes out.
A loud noise from the
appliance.
Not enough water in the tank. Fill the tank.
The rst use process has not been carried
out or has not been carried out correctly.
Carry out the rst use process for the
water (refer to the paragraph on rst
use).
The internal system needs to ll up again. Press and hold the steam control
button.
Do not completely empty the water
tank.
Cartridge
Anti calc maintenance
Do not put any descaling substances (vinegar,industrial descaling products, etc.) in the water tank or in the anti calc
compartment, they could damage your appliance.
Using the appliance without changing the cartridge can damage the appliance and stop its steaming performance. Press
on the anti calc button only if you have changed the cartridge.
To ensure the eciency of the cartridge, please remove it from its plastic bag just before use. The international guarantee
will not cover any damages which occurs as a result of using the appliance without changing the cartridge.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Tefal QT1020E0 User manual
- Category
- Steam ironing stations
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Tefal QR1020 User manual
-
-
-
-
-
Tefal SV6110G0 User manual
-
-
-
Tefal SV9202G0 User manual
-
Other documents
-
Rowenta IXEO QR10XX User manual
-
Philips GC7619/20 Owner's manual
-
Philips GC6833/36 Quick start guide
-
-
-
Groupe SEB USA - T-FAL Electric Iron User manual
-
Philips GC6630/20 Owner's manual
-
Philips GC7710/20 Quick start guide
-
Iron-A-Way ANE42WDU-L Specification
-