Operating Instructions and Parts Manual
20” Electronic Variable Speed Drill Press
Models: JDP-20EVS-110, JDP-20EVST-230,-460
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-354220
Ph.: 800-274-6848 Edition 6 10/2019
www.jettools.com Copyright © 2018 JET
JDP-20EVST-230 shown
for models with serial no.
1910257 and higher.
This .pdf document is bookmarked
2
1.0 IMPORTANT SAFETY INSTRUCTIONS
- Misuse of this machine can cause serious
injury.
- For safety, machine must be set up, used and
serviced properly.
- Read, understand and follow instructions in
the Operating Instructions and Parts Manual
which was shipped with your machine.
When setting up machine:
- Always avoid using machine in damp or
poorly lighted work areas.
- Always be sure the machine support is
securely anchored to the floor or the work
bench.
When using machine:
- Always wear safety glasses with side shields
(See ANSI Z87.1)
- Never wear loose clothing or jewelry.
- Never overreach—you may slip and fall.
When servicing machine:
- Always disconnect the machine from its
electrical supply while servicing.
- Always follow instructions in Operating
Instructions and Parts Manual when changing
accessory tools or parts.
- Never modify the machine without consulting
JET.
You—the stationary power tool user—hold the
key to safety.
Read and follow these simple rules for best results
and full benefits from your machine. Used properly,
JET machinery is among the best in design and
safety. However, any machine used improperly can
be rendered inefficient and unsafe. It is absolutely
mandatory that those who use our products be
properly trained in how to use them correctly. They
should read and understand the Operating
Instructions and Parts Manual as well as all labels
affixed to the machine. Failure to follow all of these
warnings can cause serious injuries.
1.1 Machinery general safety warnings
1. Always wear protective eye wear when
operating machinery. Eye wear shall be impact
resistant, protective safety glasses with side
shields which comply with ANSI Z87.1
specifications. Use of eye wear which does not
comply with ANSI Z87.1 specifications could
result in severe injury from breakage of eye
protection.
2. Wear proper apparel. No loose clothing or
jewelry which can get caught in moving parts.
Rubber soled footwear is recommended for
best footing.
3. Do not overreach. Failure to maintain proper
working position can cause you to fall into the
machine or cause your clothing to get caught,
pulling you into the machine.
4. Keep guards in place and in proper working
order. Do not operate the machine with guards
removed.
5. Avoid dangerous working environments. Do
not use stationary machine tools in wet or
damp locations. Keep work areas clean and
well lit.
6. Avoid accidental starts by being sure the start
switch is “OFF” before plugging in the
machine.
7. Never leave the machine running while
unattended. Machine shall be shut off
whenever it is not in operation.
8. Disconnect electrical power before servicing.
Whenever changing accessories or general
maintenance is done on the machine,
electrical power to the machine must be
disconnected before work is done.
9. Maintain all machine tools with care. Follow all
maintenance instructions for lubricating and
the changing of accessories. No attempt shall
be made to modify or have makeshift repairs
done to the machine. This not only voids the
warranty but also renders the machine unsafe.
10. Machinery must be anchored to the floor.
11. Secure work. Use clamps or a vise to hold
work, when practical. It is safer than using your
hands and it frees both hands to operate the
machine.
12. Never brush away chips while the machine is
in operation.
13. Keep work area clean. Cluttered areas invite
accidents.
14. Remove adjusting keys and wrenches before
turning machine on.
3
15. Use the right tool. Don’t force a tool or
attachment to do a job for which it was not
designed.
16. Use only recommended accessories and
follow manufacturer’s instructions pertaining to
them.
17. Keep hands in sight and clear of all moving
parts and cutting surfaces.
18. All visitors should be kept at a safe distance
from the work area. Make workshop
completely safe by using padlocks, master
switches, or by removing starter keys.
19. Know the tool you are using — its application,
limitations, and potential hazards.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious or even fatal
injury.
1.2 General electrical cautions
This drill press should be grounded in accordance with the National Electrical Code and local codes and
ordinances. This work should be done by a qualified electrician. The saw must be grounded to protect the user
from electrical shock.
Wire sizes
Caution: For circuits which are far away from the electrical service box, the wire size must be increased in
order to deliver ample voltage to the motor. To minimize power losses and to prevent motor overheating and
burnout, the use of wire sizes for branch circuits or electrical extension cords according to Table 1 (sect. 6.3) is
recommended.
WARNING: Some dust, fumes and gases
created by power sanding, sawing, grinding,
drilling, welding and other construction activities
contain chemicals known to the State of
California to cause cancer and birth defects or
other reproductive harm. Some examples of
these chemicals are:
lead from lead based paint
crystalline silica from bricks, cement and
other masonry products
arsenic and chromium from chemically
treated lumber
Your risk of exposure varies, depending on how
often you do this type of work. To reduce your
exposure to these chemicals, work in a well-
ventilated area and work with approved safety
equipment, such as dust masks that are
specifically designed to filter out microscopic
particles. For more information go to http://
www.p65warnings.ca.gov/ and http://www.
p65warnings.ca.gov/wood.
WARNING: This product can expose you to
chemicals including lead and cadmium which
are known to the State of California to cause
cancer and birth defects or other reproductive
harm, and phthalates which are known to the
State of California to cause birth defects or
other reproductive harm. For more information
go to http://www.p65warnings.ca.gov.
4
1.3 Safety instructions for drill presses
1. All work shall be secured using either clamps
or a vise to the drill press table. It is unsafe to
use your hands to hold any workpiece being
drilled.
2. Drill press head and table shall be securely
locked to the column before operating the drill
press. This must always be checked prior to
starting the machine.
3. Always use the correct tooling. Tooling shall
always be maintained and properly sharpened.
All tooling must be run at the proper speeds
and feeds as they apply to the job. Use only
recommended accessories and follow those
manufacturer’s instructions pertaining to them.
Tooling shall not be forced in to any work
piece but fed according to the proper
specifications. Failure to follow these
instructions will not only ruin the tooling as well
as the machine, but can cause serious injury.
4. Never brush away any chips while the
machine is in operation. All clean up should be
done when the machine is stopped.
5. Keep hands in sight. Do not put hands or
fingers around, on, or below any rotating
cutting tools. Leather safety gloves should be
used when handling any sharp objects or
cutting tools. See Figure A.
6. Always wear protective eye wear when
operating, servicing or adjusting machinery.
Eyewear shall be impact resistant, protective
safety glasses with side shields complying with
ANSI Z87.1 specifications. Use of eye wear
which does not comply with ANSI Z87.1
specifications could result in severe injury from
breakage of eye protection. Figure B.
7. When drilling in material which causes dust, a
dust mask shall be worn. See Figure C.
8. Avoid contact with coolant, especially guarding
the eyes.
9. Non-slip footwear and safety shoes are
recommended. See Figure D.
10. Wear ear protectors (plugs or muffs) during
extended periods of operation. See Figure E.
Figure 1-1
SAVE THESE INSTRUCTIONS
2.0 About this manual
This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model
JDP-20EVS series Drill Press. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and
constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth in
this document.
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our
web site: www.jettools.com.
Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.
Read and understand the entire contents of this manual before attempting assembly
or operation! Failure to comply may cause serious injury!
5
3.0 Table of Contents
Section Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2
1.1 Machinery general safety warnings ............................................................................................................ 2
1.2 General electrical cautions ......................................................................................................................... 3
1.3 Safety instructions for drill presses ............................................................................................................. 4
2.0 About this manual .......................................................................................................................................... 4
3.0 Table of Contents ........................................................................................................................................... 5
4.0 Specifications ................................................................................................................................................. 6
4.1 Mounting hole centers (all models) ............................................................................................................ 7
5.0 Set-Up and Assembly .................................................................................................................................... 8
5.1 Securing base ............................................................................................................................................ 8
5.2 Raising head .............................................................................................................................................. 8
6.0 Electrical Connections .................................................................................................................................... 8
6.1 Electrical box access .................................................................................................................................. 9
6.2 GROUNDING INSTRUCTIONS ................................................................................................................. 9
6.3 Extension cords .......................................................................................................................................... 9
7.0 Operating controls .......................................................................................................................................... 9
8.0 Adjustments ................................................................................................................................................. 10
8.1 Depth stop ................................................................................................................................................ 10
8.2 Table adjustment ...................................................................................................................................... 10
8.3 Tool installation and removal .................................................................................................................... 11
8.4 Speed pickup adjustment (all models) ..................................................................................................... 11
8.5 Spindle return spring adjustment .............................................................................................................. 11
8.6 Coolant pump ........................................................................................................................................... 11
9.0 Operation ..................................................................................................................................................... 12
9.1 Operating precautions .............................................................................................................................. 12
9.2 Drilling recommendations ......................................................................................................................... 12
10.0 User-maintenance ...................................................................................................................................... 13
10.1 Drive belt replacement ........................................................................................................................... 13
10.2 Motor replacement ................................................................................................................................. 13
10.3 Lubrication .............................................................................................................................................. 13
11.0 Troubleshooting JDP-20EVS series Drill Presses ..................................................................................... 14
12.0 Replacement Parts ..................................................................................................................................... 15
12.1.1 JDP-20EVS-110 Top Head Assembly – Exploded View ..................................................................... 16
12.1.2 JDP-20EVS-110 Top Head Assembly – Parts List .............................................................................. 17
12.2.1 JDP-20EVS-110 Table and Base Assembly – Exploded View ........................................................... 19
12.2.2 JDP-20EVS-110 Table and Base Assembly – Parts List .................................................................... 20
12.3.1 Spindle Components (all models) – Exploded View ............................................................................ 22
12.3.2 Spindle Components (all models) – Parts List .................................................................................... 23
12.4.1 Safety Shield Assembly (all models) – Exploded View ....................................................................... 24
12.4.2 Safety Shield Assembly (all models) – Parts List ................................................................................ 24
12.5.1 JDP-20EVST-230/460 Top Head Assembly – Exploded View ............................................................ 25
12.5.2 JDP-20EVST-230/460 Top Head Assembly – Parts List .................................................................... 26
12.6.1 JDP-20EVST-230/460 Base and Table Assembly – Exploded View .................................................. 28
12.6.2 JDP-20EVST-230/460 Base and Table Assembly – Parts List ........................................................... 29
13.0 Electrical connections ................................................................................................................................ 31
13.1 JDP-20EVS-110 wiring diagram ............................................................................................................. 31
13.2 JDP-20EVST-230 wiring diagram .......................................................................................................... 32
13.3 JDP-20EVST-460 wiring diagram .......................................................................................................... 33
14.0 Warranty and Service ................................................................................................................................. 34
6
4.0 Specifications
Model number ....................................................... JDP-20EVS-110 ............ JDP-20EVST-230.......... JDP-20EVST-460
Stock number .......................................................................354220 ............................. 354225........................... 354226
Motor and Electricals:
Motor type .......................................................... TEFC induction ................ TEFC induction.............. TEFC induction
Horsepower .......................................................... 2 HP (1.5kW) ................... 2 HP (1.5kW)................. 2 HP (1.5kW)
Phase ...................................................................................... 3 ....................................... 3..................................... 3
Voltage .............................................................................. 230 V ............................... 230 V............................. 460 V
Cycle .................................................................................. 60Hz ................................ 60Hz.............................. 60Hz
Listed FLA (full load amps) ...................................................... 6 ....................................... 6..................................... 3
Motor speed ....................................................................... 1720 ................................. 1720............................... 1720
Inverter ............................................ economic type, 115V, 1PH ....... M-type, 230V, 1/3PH......... M-type, 460V, 3PH
Power input requirements ................................... 115V, 1 phase ......... 230V, 1 or 3 phase............... 460V, 3 phase
Starting amps ..................................................................... 9.2 A ..................................... ---................................... ---
Running amps (no load) .................................................... 1.7 A ..................................... ---................................... ---
Power cable ....................................................... 3x14AWG, 6 ft. .................... 14AWG, 6 ft................... 14AWG, 6 ft.
Power plug ......................................................................... 120V ..................... not provided................... not provided
Recommended circuit and fuse/breaker size
1
....................... 15 ..................................... 15................................... 15
Sound emission without load
2
.......................................... 70 dB ............................... 70 dB............................. 70 dB
Coolant pump ................................................. 1/8HP 115V 1PH ............. 1/8HP 230V 1PH............ 1/8HP 460V 3PH
Capacities:
Drilling capacity, cast iron .............................................. 1-1/2 in. ............................ 1-1/2 in........................... 1-1/2 in.
Drilling capacity, mild steel............................................. 1-3/8 in. ............................ 1-3/8 in........................... 1-3/8 in.
Tapping capacity, cast iron ................................................... n/a ............................... 7/8 in.............................. 7/8 in.
Tapping capacity, mild steel.................................................. n/a ............................... 3/4 in.............................. 3/4 in.
Spindle to table maximum distance ............................. 30-1/4 in. .......................... 30-1/4 in......................... 30-1/4 in.
Spindle to base maximum distance ............................. 44-1/2 in. .......................... 44-1/2 in......................... 44-1/2 in.
Spindle to column maximum distance ....... 10-7/16 in. (265mm) ........ 10-7/16 in. (265mm)....... 10-7/16 in. (265mm)
Coolant capacity ........................................................ 2 gal. (9L) ........................ 2 gal. (9L)....................... 2 gal. (9L)
Spindle:
Spindle taper ...................................................................... MT-3 ................................ MT-3.............................. MT-3
Spindle speed ................................................................ variable ............................ variable.......................... variable
Spindle speed range ....................................... 65-540/245-2000 ............. 65-540/245-2000............ 65-540/245-2000
Spindle travel ................................................... 6 in. (152.4 mm) ...............6 in. (152.4 mm)............. 6 in. (152.4 mm)
Gear reduction ................................................................ 48/35T ............................. 48/35T............................ 48/35T
Rotation .......................................................................... fwd/rev ............................. fwd/rev........................... fwd/rev
Table and Column:
Table size ................................................................................... 22 x 18-3/4 in. (559 x 476 mm) ...............................
Table working surface ................................................................ 18-1/8 x 14-3/4 in. (460 x 375 mm) .........................
Table travel
Without rack adjustment ............................... 15 in. (381mm) ................ 15 in. (381mm)............... 15 in. (381mm)
Maximum travel with rack adjustment ........... 20 in. (508mm) ................ 20 in. (508mm)............... 20 in. (508mm)
T-slot number ........................................................................... 3 ....................................... 3..................................... 3
T-slot size ............................................................ 5/8 in. (16mm) ................. 5/8 in. (16mm)................ 5/8 in. (16mm)
T-slot centers ............................................... 7-7/16 in. (189mm) .......... 7-7/16 in. (189mm)......... 7-7/16 in. (189mm)
Table weight capacity ........................................... 154 lb. (70kg) ................... 154 lb. (70kg)................. 154 lb. (70kg)
Column diameter ........................................... 4-1/2 in. (114mm) ............ 4-1/2 in. (114mm)........... 4-1/2 in. (114mm)
Base:
Base size ................................................................................... 27 x 19 in. (686 x 483mm) ......................................
Base working surface…………………………………………….14-3/4 x 11-13/16 in. (375 x 300mm) ..........................
T-slot number ........................................................................... 2 ....................................... 2..................................... 2
T-slot size ............................................................ 5/8 in. (16mm) ................. 5/8 in. (16mm)................ 5/8 in. (16mm)
Main materials:
Head .......................................................... cast iron, steel cover ........ cast iron, steel cover...... cast iron, steel cover
Table and Base ............................................................. cast iron ........................... cast iron......................... cast iron
Spindle and Quill ................................................................. steel ................................. steel............................... steel
Column ............................................................................... steel ................................. steel............................... steel
7
Dimensions:
Assembled machine dimensions (LxWxH)……………38-3/16 x 27-5/32 x 79-1/2 in. (970 x 690 x 2020mm) ............
Shipping crate dimensions (LxWxH) .......................................... 37 x 25.5 x75 in. (939 x 648 x1905mm) ..................
Weights:
Net weight ........................................................... 723 lb(328 kg). ................. 723 lb(328 kg)................. 723 lb(328 kg)
Shipping weight .................................................. 781 lb (355 kg) ................. 781 lb (355 kg) .............. 781 lb (355 kg)
1
Subject to local and national electrical codes.
2
The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace
conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks
involved only.
L = length, W = width, H = height
n/a = not applicable
The above specifications were current at the time this manual was published, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
4.1 Mounting hole centers (all models)
Figure 4-1: machine base mounting
8
5.0 Set-Up and Assembly
Inspect contents of crate for shipping damage.
Report any damage immediately to your distributor
and shipping agent. Do not discard any shipping
material until drill press is assembled and running
properly.
Remove any fasteners holding drill press to pallet.
Lift drill press with forklift or hoist with straps.
(Note: Lifting point is beneath head and next to
column.) Make sure coolant hose, handles, etc. are
clear of forks or straps when lifting. Lifting
equipment must be properly rated for weight of
drill press.
Locate the machine on a solid, level floor,
preferably concrete. Area should have good
overhead lighting and ventilation. (Refer to OSHA
regulations for specific information about using drill
presses in industrial environments.) The drill press
should be level and rest solidly on floor. Place
shims below base as needed to achieve level.
Exposed metal surfaces have been given a
protective coating. Remove this with a soft cloth
and a cleaner-degreaser or kerosene. Do not use
gasoline, paint thinner or acetone, as these may
damage painted surfaces. Do not use an abrasive
pad, as it may scratch polished surfaces.
Coat all machined surfaces with a light coat of oil to
inhibit rust.
5.1 Securing base
It is highly recommended that the drill press be
secured to floor. The base of the drill press has
four mounting slots; see Figure 4-1. When securing
base to floor, apply even torque to the fasteners to
prevent distortion of base.
5.2 Raising head
The drill press head is lowered on the column for
crating and transportation. Before operating drill
press, head must be raised to operational level, as
follows.
1. Cut a 2x4 approximately 16-inches in length.
2. Loosen head locking nut (A, Figure 5-1) by
turning counterclockwise with provided socket
wrench.
3. Grasp head and turn it slightly from side to
side to loosen the rust prevention solution on
column.
4. Loosen table lock by placing handle on
crankshaft (see A, Figure 8-2) and rotating
handle counterclockwise.
5. Raise table by placing handle on crankshaft (B
or C, Figure 8-2) and rotating clockwise. Place
2x4 vertically between table and head, as
close to column as possible. CAUTION: Do not
place 2x4 under lock collar (B, Figure 5-1).
6. Continue raising head and 2x4 until head bore
and column are flush. Use a ladder to observe
column through top of pulley cover.
Do not raise head any
farther or it may fall from column. Failure to
comply may result in serious injury.
7. Securely tighten head locking nut (A, Figure 5-
1). This will secure head until lock collar can
be positioned. The 2x4 can now be safely
removed.
8. Loosen two set screws on lock collar (B), and
slide lock collar until it is flush with head.
Securely tighten both set screws.
Never loosen head locking nut
(A) without supporting the head.
Figure 5-1
6.0 Electrical Connections
Electrical connections must
be made by a qualified electrician in
compliance with all relevant codes. This
machine must be properly grounded to help
prevent electrical shock and possible fatal
injury.
The JDP-20EVS-110 Drill Press is pre-wired for 1-
phase, 115-volt. It is provided with an electrical
plug. See sect. 6.2.
The JDP-20EVST-230 is pre-wired for 3-phase,
230-volt. It is not provided with an electrical plug;
you may either attach a proper UL-listed plug, or
“hardwire” the machine directly to a service panel.
The machine can also be run on 1-phase power
(230-volt). See sect. 6.2.
The JDP-20EVST-460 is pre-wired for 3-phase,
460-volt only. It is not provided with an electrical
plug; you may either attach a proper UL-listed plug,
or “hardwire” the machine directly to a service
panel. See sect. 6.2.
9
6.1 Electrical box access
Push latch button and rotate latch counter-
clockwise to open. Use the provided key to lock the
electrical box to prevent unauthorized entry.
6.2 GROUNDING INSTRUCTIONS
This tool must be grounded. In the event of a
malfunction or breakdown, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. This tool is
equipped with an electric cord having an
equipment-grounding conductor. If the machine is
supplied with an electrical plug, the plug must be
inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Improper connection of the
equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified
electrician or service person if you are in doubt
as to whether the outlet is properly grounded.
Do not modify the plug provided with the tool –
if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
The conductor with insulation having an outer
surface that is green with or without yellow stripes
is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-
grounding conductor to a live terminal.
Repair or replace damaged or worn cord
immediately.
If the drill press is to be hard-wired to a panel,
make sure a disconnect is available for the
operator. During hard-wiring of the machine, make
sure the fuses have been removed or the breakers
have been tripped in the circuit to which the drill
press will be connected. ALWAYS FOLLOW
PROPER LOCK-OUT/TAG-OUT PROCEDURES.
Model JDP-20EVST-230 (3-Phase) is pre-wired for
230 volt only. The machine can also be run on 1-
Phase power by hooking up the ground, L1 and L2
wires, as explained below.
Model JDP-20EVS-460 (3-Phase) is pre-wired for
460 volt only.
To wire the drill press:
If using a power cord, strip back the cord until
about 3 to 4 inches of the lead wires are exposed.
Slide a grommet onto the cord to be installed later
in electrical box hole, to prevent stress to power
cord.
1. Bring the lead wires through hole in machine’s
electrical box and connect as follows (refer to
Figure 6-1):
2. If your incoming power is single phase,
connect the two leads to L1 and L2, and the
green ground wire to the grounding screw.
3. If your incoming power is three phase,
connect the three leads to L1, L2 and L3, and
the green ground wire to the grounding screw.
Make sure incoming current matches power
requirements of the drill. When machine is
connected properly, spindle turns clockwise in a
conventional drilling rotation. If spindle does not
turn clockwise, disconnect drill from power supply
and reverse any two of the three power leads
(except green ground wire).
Figure 6-1: shows three-phase connection
6.3 Extension cords
The use of extension cords is discouraged; try to
position equipment within reach of power source. If
an extension cord becomes necessary, be sure it is
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table 1 shows recommended size to use
depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Ampere
Rating
Volts
Total length of
cord in feet
More
Than
Not
More
Than
120
240
25
50
50
100
100
200
150
300
AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12
Not
Recommended
Table 1: extension cord recommendations
7.0 Operating controls
The front panel (Figure 7-1) contains all the
controls required to operate the drill press. The
A.C. inverter in the electrical box does not require
any programming, it is pre-programmed from the
factory. Do not attempt to change inverter
settings. Use only the controls on the front panel.
If you suspect a problem with the inverter or its
10
settings, contact JET technical service at 1-800-
274-6848.
Figure 7-1: controls (JDP-20EVST-230 shown)
Spindle On (A): Starts drive motor. To stop motor,
press button again (toggles on and off).
Spindle off (B): Stops spindle rotation. (NOTE:
Other functions such as coolant pump will continue
to operate.)
Reverse spindle (C): Functional only in tapping
mode. If tapping is interrupted, press this button to
reverse tap from workpiece.
E-Stop (D): Emergency stop button shuts down all
drill press functions. To reset, turn E-stop button
clockwise until it disengages.
Coolant pump (E): Starts and stops coolant pump
circulation.
LED Display (F): Shows spindle RPM selected by
speed control knob.
Speed control (G): Selects spindle speed based
upon range set by speed shift lever.
Drill mode (H): Selects drill or tap mode (JDP-
20EVST models only).
Speed shift lever (I): Selects high or low speed
range. See sect. 4.0 for ranges.
Spindle must be stopped
before attempting to adjust speed shift
lever. Failure to comply may damage speed
adjustment mechanism.
NOTE: The Electronic Variable Speed unit is
designed to shut down, to prevent harm to the
system, in the event of overloading the spindle.
Make sure the Speed Control knob and the High-
Low Handle are in the matching ranges for the
work being done. Drilling large holes requires High-
Low Handle to be in ‘Low’ mode and Speed
Control Knob to be selecting a speed that is high
enough to power the large bit.
8.0 Adjustments
8.1 Depth stop
The drilling depth indicator (Figure 8-1) can be set
for depths up to 6 inches (152.4 mm).
8.1.1 For drilling (all models)
Set switch to drill mode.
Before starting motor, set end of drill against
surface into which hole is to be drilled. Zero out
indicator by turning knurled knob (J). Lock indicator
setting at zero by tightening knob (K). Start motor
and drill hole until indicator line reaches desired
depth.
8.1.2 For tapping (JDP-20EVST models)
Set depth stop in same manner as above. When
quill is advanced, upper limit switch will be
released for tapping. When lower limit switch is
triggered, spindle will reverse rotation direction.
Figure 8-1: depth indicator
8.2 Table adjustment
The table can be raised or lowered to
accommodate workpiece height. Place hand crank
on shaft (A, Figure 8-1) and turn to loosen table
lock. Then use hand crank on shaft B or C to raise
or lower table. Lock table in position using shaft A.
If drill press base is to be used for securing
workpiece, loosen table (A) and swing it around
column and out of the way. Retighten table.
11
Figure 8-2: table adjustments
8.3 Tool installation and removal
1. Disconnect machine from power source.
2. Thoroughly clean inside of spindle with a soft
dry cloth. Also clean any taper or arbor to be
used in the spindle. If these are not kept clean,
taper or arbor will not “seat” properly in spindle
and may drop out unexpectedly.
3. Place protective piece of scrap wood on table.
4. Raise table to approximately 8 to 10 inches
below spindle.
5. Insert MT3 tool into spindle.
6. Lower spindle using side handle, and seat tool
against the wood.
To remove a tool:
1. Disconnect machine from power source.
2. Lower spindle to expose slots in spindle wall.
3. Insert drift key into spindle slots and tap gently
until drill bit or chuck arbor loosens. Hold tool
with one hand (use glove or rag if needed)
while tapping to prevent tool from falling and
being damaged.
8.4 Speed pickup adjustment (all
models)
Refer to exploded view, sect. 12.3.2.
1. Loosen screws securing speed pickup (ref.
68A) to plate (ref. 69A).
2. Adjust speed pickup gap to approximately 1/8-
inch. Re-tighten screws.
3. Operate drill press to verify that speed readout
is operating correctly.
8.5 Spindle return spring adjustment
The spindle return is preset by the manufacturer
and should not need adjustment. If future attention
is ever required, proceed as follows:
1. Do NOT remove spring cap (D, Figure 8-3).
2. Loosen screws (E) just enough to rotate spring
cap past pin (F) and engage pin into next
notch.
3. Rotate spring cap clockwise to decrease
spring tension. Rotate spring cap counter-
clockwise to increase spring tension.
4. Re-tighten both screws (E).
Figure 8-3
8.6 Coolant pump
The coolant system should be filled with 2 gallons
of a cutting coolant. Fill by pouring coolant into
base of machine. Add coolant in the same manner
when coolant is low. To drain coolant, remove hex
cap screw located on lower backside of base.
Follow all coolant manufacturer’s instructions for
safety, mixing and disposal.
Make sure drain hose has good, tight connection
into table and that coolant flows into base.
Make sure hose leaving pump and entering ball
valve has good, tight connections.
The flexible nozzle enables user to adjust coolant
for each job. One ball valve controls coolant fllow
to nozzle.
12
9.0 Operation
9.1 Operating precautions
The following operating and safety precautions
must be observed in order to avoid harm to
operator or damage to drill press.
1. Head assembly must be locked to column so
the thrust produced by drilling will not force the
head assembly up the column.
2. Work table must be locked to column so it will
not be forced down the column.
3. Be sure belt is tightened to proper tension.
4. Do NOT start to drill workpiece until making
certain workpiece is held down securely.
5. MAKE SURE DRIVE MOTOR IS RUNNING
BEFORE turning speed shift lever (I, Figure 7-
1) in either direction.
6. Point of operation protection is required for
maximum safety. This remains the
responsibility of the user/purchaser since
conditions differ between jobs.
7. Make sure the drill is secured in the spindle or
chuck before attempting to use the drill press.
8. Make sure spindle taper is clean and free of
burrs, scoring, and galling to assure maximum
gripping.
9.2 Drilling recommendations
9.2.1 Drilling speeds
The speed of a drill is usually measured in terms of
the rate at which the outer periphery of the tool
moves in relation to the work being drilled. The
common term for this is Surface Feet per Minute
(SFM). The relationship of SFM is expressed in the
following formulas:
SFM = 0.26 X rpm X Drill Diameter (in inches)
RPM = 3.8 x ________SFM__________
Drill diameter (in inches)
In general, the higher the speed the shorter the drill
life. Operating at the low end of the speed range
for a particular material will result in longer life. The
most efficient speed for drill operation depends
upon many variables:
1. Composition and hardness of material.
2. Depth of hole.
3. Efficiency of cutting fluid.
4. Type and condition of drilling machine.
5. Desired quality of hole.
6. Difficulty of set-up.
9.2.2 Drilling feed
The feed of a drill is governed by size of tool and
the material drilled. Because feed rate partially
determines rate of production and also is a factor in
tool life, it should be chosen carefully for each job.
In general, the most effective feeds will be found in
the following ranges:
Diameter of Drill
(inches)
Feed per Revolution
(inches)
Under 1/8 0.001 to 0.002
1/8 to 1/4 0.002 to 0.004
1/4 to 1/2 0.004 to 0.007
1/2 to 5/8 0.007 to 0.015
Table 2
9.2.3 Excessive speed/feed indicators
A drill that splits up the web is evidence of too
much feed or insufficient tip clearance at the center
as a result of improper grinding. The rapid wearing
away of the extreme outer corners of cutting edges
indicates that speed is too high. A drill chipping or
breaking out at the cutting edges indicates that
either feed is too heavy or drill has been ground
with too much tip clearance.
9.2.4 Speeds for high speed steel drills
Material
Speed
(SFPM)
Alloy Steel — 300 to 400 Brinell 20-30
Stainless Steel 30-40
Automotive Steel Forgings 40-50
Tool Steel, 1.2C 50-60
Steel, .4C to .5C 70-80
Mild Machinery Steel, .2C to .3C 80-110
Hard Chilled Cast Iron 30-40
Medium Hard Cast Iron 70-100
Soft Cast Iron 100-150
Malleable Iron 80-90
High Nickel Steel or Monel 40-50
High Tensile Bronze 70-150
Ordinary Brass and Bronze 200-300
Aluminum and its Alloys 200-300
Magnesium and its Alloys 250-400
Slate, Marble, and Stone 15-25
Plastics and similar materials (Bakelite) 100-150
Wood 300-400
Titanium Alloys 10-25
Titanium Alloy Sheet 50–60
Note: In cases where carbon steel drills are applicable, the
drill should be run at speeds of 40 to 50 percent of those
given above.
Table 3
13
10.0 User-maintenance
10.1 Drive belt replacement
Disconnect electrical power to
drill press to avoid possibility of inadvertent
operation and exposure to potentially lethal
voltage levels.
1. Disconnect electrical power by setting drill
press circuit breaker to OFF.
2. Loosen set screw and remove high/low shift
lever.
3. Remove screws and take off pulley cover.
4. Disconnect electrical wiring from motor
junction box, and remove motor.
5. Remove used belt. Install replacement belt.
6. Install motor and connect electrical wiring
(refer to Wiring Diagram section for wiring
details).
7. Install pulley cover and secure with screws.
8. Set the drill press circuit breaker ON.
9. Operate drill press to verify correct operation.
10.2 Motor replacement
Disconnect electrical power to
drill press to avoid possibility of inadvertent
operation and exposure to potentially lethal
voltage levels.
1. Disconnect electrical power by setting drill
press circuit breaker to OFF.
2. Follow steps under sect. 12.1 to remove drive
motor.
10.3 Lubrication
See Table 4 for lubrication points and frequency.
Oil fill tube:
a. Periodically check oil level in sight gauge
(A, Figure 10-1).
b. If level is below centerline of sight gauge,
add oil.
c. To add oil, remove oil fill tube cover plate.
Pull fill tube out of hole in head cover (B).
d. Add oil to bring oil level up to centerline of
sight gauge.
e. Put end of fill tube back through hole in
head cover. Install fill tube cover and
secure with two screws.
Figure 10-1
Lubrication points
Location Type Frequency
Splines on spindle shaft (access
through hole atop pulley cover)
#2 lithium based tube grease Monthly
Quill and column Machine tool oil Daily
Lift rack 20W non-detergent oil
Weekly (clean rack with kerosene
before lubricating)
Table lift Gear grease Twice yearly (clean and regrease)
Oil fill tube (behind plate on left side
of drill head; see Figure 10-1)
Mobil DTE Heavy Medium
Change after initial 6 months, then
annually thereafter. Capacity = 1
quart. Drain plug is located in
cutaway section on underside of
head.
Table 4
14
11.0 Troubleshooting JDP-20EVS series Drill Presses
Trouble Probable Cause Remedy
Spindle does not turn.
Motor overload protector tripped. Press motor overload reset button.
Circuit breaker tripped. Reset circuit breaker.
Branch circuit breaker tripped or fuse
blown.
Reset branch circuit breaker/replace fuse.
Open wire in switch circuit. Repair open circuit.
Defective switch. Replace switch.
Broken drive belt. Replace drive belt.
Spindle noisy.
Damaged spindle bearings. Replace bearings.
Worn spline. Replace spline.
Drill stalls.
Worn drive belt.
Check condition of belt. Replace if glazed
or slipping on pulleys.
Excessive feed rate for size of drill and
material being drilled. No cutting fluid or
improper cutting fluid.
Reduce feed pressure or use cutting fluid.
Use correct cutting fluid.
Poorly drilled holes.
Drill dull. Sharpen drill.
Lack of rigidity in hold-down method.
Check that all T-slot hold-downs are tight
and that table-lock and drill head bolts are
tight.
Speed too fast for material and drill size.
Check spindle speed recommendations.
Reduce speed if necessary.
Feed too fast for material and drill size. Reduce feed rate.
No or improper cutting fluid or coolant
being used.
Use cutting fluid, or change to proper fluid
or coolant for material being drilled.
Improperly ground drill bit.
Check for proper angles and reliefs.
Regrind to proper geometry.
Motor overheating.
Electrical circuit fault.
Check current draw in circuit. Make sure
current draw is the same as rating on
motor plate.
Oversize drill. Reduce drill size.
Excessive feed. Reduce feed rate.
No cutting fluid, or wrong fluid.
Use correct cutting fluid for the material
and drill.
Table cannot be raised. Lack of lubrication. Lubricate.
No speed readout. Speed pickup out of adjustment or failed.
Adjust gap between speed pickup and
post spindle pulley. If there is no readout
on the LED speed indicator after adjusting
the gap, replace the speed pickup.
Table 5
15
12.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-
800-274-6848, Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial
Number of your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually.
16
12.1.1 JDP-20EVS-110 Top Head Assembly – Exploded View
17
12.1.2 JDP-20EVS-110 Top Head Assembly – Parts List
Index No. Part No. Description Size Qty
1 ................. J-5517332ACG ........... Head Casting ............................................................... ........................................ 1
2 ................. 5510142 ...................... Oil Window ................................................................... ........................................ 1
3 ................. 5510143 ...................... Ball Bearing .................................................................. ........................................ 1
4 ................. 5510144 ...................... Retaining Ring ............................................................. ........................................ 1
5 ................. 5510145 ...................... Gear ............................................................................. 32T .................................. 1
6 ................. 5510146 ...................... Key ............................................................................... ........................................ 1
7 ................. 5510147 ...................... Drive Shaft ................................................................... 13T .................................. 1
8 ................. 5510148 ...................... Ball Bearing .................................................................. ........................................ 1
9 ................. 5510149 ...................... Retaining Ring ............................................................. ........................................ 1
10 ............... 5510150 ...................... Ball Bearing .................................................................. ........................................ 1
11 ............... 5510151 ...................... Retaining Ring ............................................................. ........................................ 1
12 ............... 5510153 ...................... Gear ............................................................................. 55T .................................. 1
13 ............... 5510152 ...................... Set Screw..................................................................... ........................................ 1
14 ............... 5510155 ...................... Spring .......................................................................... ........................................ 1
15 ............... 5510154 ...................... Steel Ball ...................................................................... ........................................ 1
16 ............... 5510159 ...................... Key ............................................................................... ........................................ 1
17 ............... 5517333 ...................... Drain Plug .................................................................... 3/8 NPT ........................... 1
18 ............... 5510158 ...................... Gear ............................................................................. 18T .................................. 1
20 ............... 5510160 ...................... Key ............................................................................... ........................................ 1
21 ............... 5510161 ...................... Mid Shaft ...................................................................... ........................................ 1
22 ............... 5510162 ...................... Key ............................................................................... ........................................ 1
23 ............... 5510163 ...................... Retaining Ring ............................................................. ........................................ 2
24 ............... 5510164 ...................... Ball Bearing .................................................................. ........................................ 1
25 ............... 5510165 ...................... Pin ................................................................................ ........................................ 1
26 ............... 5510166 ...................... Bar ............................................................................... ........................................ 1
26-1 ............ 5517334 ...................... Ring ............................................................................. ........................................ 1
27 ............... 5510167 ...................... Hex Nut ........................................................................ ........................................ 1
28 ............... 5510168 ...................... Spring Washer ............................................................. ........................................ 1
29 ............... 5510169 ...................... Speed Change Block ................................................... ........................................ 1
30 ............... 5510170 ...................... Gear Bar ...................................................................... ........................................ 1
31 ............... 5510171 ...................... Set Screw..................................................................... ........................................ 1
32 ............... 5517335 ...................... Speed Lever ................................................................. ........................................ 1
33 ............... 5517336 ...................... Retaining Ring ............................................................. ........................................ 1
34 ............... 5510173 ...................... Oil Seal ........................................................................ ........................................ 1
35 ............... 5510177 ...................... Gear Shaft .................................................................... 18T .................................. 1
36 ............... 5517337 ...................... Hex Nut ........................................................................ ........................................ 1
37 ............... 5517338 ...................... Cap Screw ................................................................... ........................................ 1
38 ............... 5510178 ...................... Set Screw..................................................................... ........................................ 1
39 ............... 5517339 ...................... Gearbox Top Cover ..................................................... ........................................ 1
40 ............... 5510180 ...................... Oil Fill Fitting ................................................................ ........................................ 1
40-1 ............ 5517340 ...................... Fill Tube ....................................................................... ........................................ 1
41 ............... 5510181 ...................... Oil Seal ........................................................................ ........................................ 1
42 ............... 5510182 ...................... Bolt ............................................................................... ........................................ 1
43 ............... 5510183 ...................... Oil Seal ........................................................................ ........................................ 1
44 ............... 5510184 ...................... Oil Seal ........................................................................ ........................................ 1
44-1 ............ 5517341 ...................... Retaining Ring ............................................................. ........................................ 1
45 ............... 5510185 ...................... Set Screw..................................................................... ........................................ 1
46 ............... 5510186 ...................... Drive Pulley .................................................................. ........................................ 1
47 ............... 5517342N ................... Spindle Pulley with Driving Sleeve ............................... 48T .................................. 1
48 ............... 5517343 ...................... Belt ............................................................................... 720x8 .............................. 1
52 ............... 5510192 ...................... Key ............................................................................... ........................................ 1
53 ............... J-5517349 ................... Motor ............................................................................ 2HP, 3PH, 220V .............. 1
54 ............... 5510194 ...................... Washer ........................................................................ ........................................ 4
55 ............... 5510195 ...................... Screw ........................................................................... ........................................ 4
56 ............... 5510204 ...................... E-stop Switch ............................................................... ........................................ 1
59 ............... 5510199 ...................... Pump Selector Switch .................................................. ........................................ 1
60 ............... 5510200 ...................... Forward/Reverse Switch .............................................. ........................................ 1
61 ............... 5510196 ...................... Speed Control Potentiometer ....................................... ........................................ 1
62 ............... 5510202 ...................... Green Pushbutton Switch ............................................ ........................................ 1
62-1 ............ JDP20EVS110-62-1 .... Power Light .................................................................. ........................................ 1
63 ............... 5510206 ...................... Screw ........................................................................... ........................................ 4
64A ............. JDP20EVS110-64A ..... Control Panel ............................................................... ........................................ 1
18
Index No. Part No. Description Size Qty
64-1 ............ 5517352 ...................... Plate Bracket ................................................................ ........................................ 1
65 ............... 5510209 ...................... Pan Head Screw .......................................................... ........................................ 2
66 ............... 5510210 ...................... Oil Filler Cover ............................................................. ........................................ 1
67 ............... J-5517353N ................ Pulley Cover ................................................................. ........................................ 1
67-4 ............ 5510215 ...................... Pan Head Screw .......................................................... ........................................ 2
67-6 ............ 5517357 ...................... Screw ........................................................................... ........................................ 2
68 ............... 5510216 ...................... Spring Washer ............................................................. ........................................ 2
69 ............... 5510217 ...................... Screw ........................................................................... ........................................ 2
70 ............... J-5517359 ................... Enclosure (w/door & latch) ........................................... ........................................ 1
71 ............... 5510219 ...................... Screw ........................................................................... ........................................ 4
72 ............... 5510220 ...................... Bolt ............................................................................... ........................................ 4
73 ............... 5517360 ...................... Washer ........................................................................ ........................................ 4
74 ............... 5510222 ...................... Cable Relief ................................................................. ........................................ 1
74-1 ............ 5517361 ...................... Cable Relief ................................................................. ........................................ 1
75 ............... 5510223 ...................... Electric Cable (to power) .............................................. 3x14AWG 300V .............. 1
75-1 ............ 5517362 ...................... Electric Cable (to work light) ........................................ 3x16AWG 300V .............. 1
76 ............... 5510224 ...................... Window Cover .............................................................. ........................................ 1
77 ............... 5517363 ...................... Component Mounting Panel ......................................... ........................................ 1
79 ............... 5510227 ...................... Insulation Board ........................................................... ........................................ 1
80 ............... 5510228 ...................... Fuse Block ................................................................... ........................................ 1
84 ............... 5517366 ...................... Cap Screw ................................................................... ........................................ 4
84-1 ............ 5517367 ...................... Lock Washer ................................................................ ........................................ 4
84-2 ............ 5517368 ...................... Hex Nut ........................................................................ ........................................ 4
85A ............. JDP20EVS-110/85A .... PC Board ..................................................................... ........................................ 1
85-1 ............ 5517371 ...................... Flat Washer .................................................................. ........................................ 4
85-2 ............ 5517372 ...................... Screw ........................................................................... ........................................ 4
86 ............... 5517373 ...................... Sub-Panel .................................................................... ........................................ 1
86-1 ............ 5517374 ...................... Screw ........................................................................... ........................................ 4
87 ............... 5510235 ...................... Terminal Block ............................................................. ........................................ 1
88 ............... 5517375 ...................... Mounting Rail ............................................................... ........................................ 1
89 ............... 5510237 ...................... Contactor ..................................................................... ........................................ 2
89-1 ............ JDP20EVS-110/POR .. Pump Overload Relay .................................................. ........................................ 1
90 ............... 5510240 ...................... Relay ............................................................................ ........................................ 2
105 ............. JDP20EVST-105 ......... LED Display ................................................................. 110V ................................ 1
106 ............. 5513683 ...................... Cap Screw ................................................................... ........................................ 2
................... LM000227 ................... ID/Warning Label, JDP-20EVS-110 (not shown) ......... ........................................ 1
................... JET-113 ...................... JET Logo (not shown) .................................................. 113x47mm ...................... 1
19
12.2.1 JDP-20EVS-110 Table and Base Assembly – Exploded View
20
12.2.2 JDP-20EVS-110 Table and Base Assembly – Parts List
Index No. Part No. Description Size Qty
1 ................. J-5510288A ................. Base ............................................................................. ........................................ 1
1-1 .............. TS-0720111 ................ Lock Washer ................................................................ 1/2" ................................ 10
1-2 .............. TS-0070031 ................ Hex Cap Screw ............................................................ 1/2" x 1-1/2” ................... 10
2 ................. J-5510289 ................... Coolant Cover Plate ..................................................... ........................................ 1
2-1 .............. 5518263 ...................... Small Cover ................................................................. ........................................ 1
2-2 .............. 20EVS-C4 ................... Screw w/Washer .......................................................... 1/4" .................................. 3
3 ................. 5510456 ...................... Coolant Pump .............................................................. 115V/230V, 1P ................ 1
4 ................. TS-1482011 ................ Hex Bolt ....................................................................... M6x10 ............................. 4
5 ................. 5517388 ...................... Pan Head Screw .......................................................... ........................................ 3
6 ................. 5510293A .................... Ball Seat....................................................................... ........................................ 1
7 ................. 5510294 ...................... Set Screw..................................................................... 3/8" .................................. 4
7-1 .............. 5517389 ...................... Brass Block .................................................................. ........................................ 4
8 ................. 5510295 ...................... Ball Bearing .................................................................. 3/8" ................................ 38
9 ................. J-5510296A ................. Lock Ring ..................................................................... ........................................ 1
9-1 .............. 5517390 ...................... Pin ................................................................................ M4 ................................... 1
10 ............... 5516859 ...................... Table Raiser Shaft ....................................................... ........................................ 1
11 ............... 5510298 ...................... Spring Pin .................................................................... 4x20 ................................ 1
12 ............... 5516858 ...................... Table Clamp Shaft ....................................................... ........................................ 1
13 ............... 5516860 ...................... Table Raiser Coupling ................................................. ........................................ 1
14 ............... 5510300 ...................... Socket Head Screw ..................................................... ........................................ 1
15 ............... TS-0561011 ................ Nut ............................................................................... 1/4" .................................. 1
16 ............... 5510302 ...................... Rack ............................................................................. ........................................ 1
17 ............... 5514663 ...................... Large Bevel Gear ......................................................... ........................................ 1
18 ............... 5517391 ...................... Bearing Housing .......................................................... ........................................ 1
18-1 ............ BB-6202ZZ .................. Ball Bearing .................................................................. 6202ZZ ............................ 2
18-2 ............ TS-0720071 ................ Washer ........................................................................ 1/4" .................................. 2
18-3 ............ TS-1482041 ................ Cap Screw ................................................................... M6x20 ............................. 2
19 ............... 5510304 ...................... Small Bevel Gear ......................................................... ........................................ 2
20A ............. J-5510305A ................. Bracket Cover .............................................................. ........................................ 1
21 ............... TS-0267041 ................ Set Screw..................................................................... 1/4"x3/8" .......................... 1
22 ............... BB-6005ZZ .................. Ball Bearing .................................................................. 6005zz ............................. 1
23 ............... 5510308 ...................... Shaft ............................................................................ ........................................ 1
24 ............... 5510309 ...................... C-Ring .......................................................................... S25 .................................. 2
25 ............... TS-1504071 ................ Hex Socket Cap Screw ................................................ M8x35 ............................. 3
26A ............. 5510311A .................... Shaft ........................................................................... ........................................ 1
29 ............... BB-51102 .................... Bearing ........................................................................ 51102 .............................. 1
30 ............... 5510315 ...................... Table Raise Worm ....................................................... ........................................ 1
31 ............... 5510316 ...................... Key ............................................................................... 4x4x20 ............................. 1
32A ............. 5510317A .................... Worm Gear Assembly ................................................. ........................................ 1
34 ............... 5510319 ...................... Front Cam Lock ........................................................... ........................................ 1
35 ............... 5510320 ...................... Rear Cam Lock ............................................................ ........................................ 1
35-1 ............ 5517396 ...................... Spring .......................................................................... ........................................ 1
35-2 ............ TS-1523071 ................ Set Screw..................................................................... M6x25 ............................. 1
35-3 ............ 5517398 ...................... Pin ................................................................................ 5x25 ................................ 2
36 ............... J-5510321 ................... Table Raise Crank ....................................................... ........................................ 2
37 ............... JDP20VST-37 ............. Table ............................................................................ ........................................ 1
37-1 ............ 5517399 ...................... Hose Coupler (Return) ................................................. 1/2" .................................. 1
38 ............... 5510323A .................... Column ........................................................................ ........................................ 1
39 ............... 5510324 ...................... Table Raise Handle ..................................................... ........................................ 1
40 ............... TS-1503021 ................ Socket Head Cap Screw .............................................. ........................................ 1
40-1 ............ TS-1550041 ................ Flat Washer .................................................................. ........................................ 1
43 ............... 5510328 ...................... Clear Vinyl Hose .......................................................... 3/8" .................................. 1
44 ............... 5510329 ...................... Hose Coupler (Supply) ................................................. 3/8" .................................. 1
45 ............... 5512112 ...................... Socket Head Cap Screw .............................................. #10-32 x 1" ...................... 4
46 ............... 5510331 ...................... Mounting Bracket ......................................................... ........................................ 1
47 ............... 5510332 ...................... Valve ............................................................................ ........................................ 1
48 ............... 5510333 ...................... Flexible Nozzle ............................................................. ........................................ 1
49 ............... 5517400 ...................... Pan Head Screw .......................................................... ........................................ 1
50 ............... 5517401 ...................... Clear Vinyl Hose .......................................................... 1/2" .................................. 1
51 ............... 5517402 ...................... Hose Clamp ................................................................. ........................................ 1
53 ............... 5517404 ...................... Drain Plug ..................................................................
.. 3/8 NPT ........................... 1
55 ............... J-5517406 ................... Rack Collar .................................................................. ........................................ 1
56 ............... 5513932 ...................... Table Raiser Assembly ................................................ ........................................ 1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
