2. ClosetMaid
  3. Offset Desktop Organizer

ClosetMaid Offset Desktop Organizer Installation guide

  • Hello! I'm a chat assistant and I have reviewed the Installation Guide for the CLOSETMAID Offset Desktop Organizer. This document includes instructions for assembling the unit, safety precautions, and parts identification. I am ready to answer any questions you have about this desktop organizer.
  • What should I do before beginning the assembly?
    What are the safety precautions?
    How do I secure the dividers to the center panel?
Skip to content
Manuals+
User Manuals Simplified.
CLOSETMAID Offset
Desktop Organizer
Installation Guide
Home » ClosetMaid » CLOSETMAID Offset Desktop
Organizer Installation Guide
Contents hide
1 CLOSETMAID Offset Desktop Organizer
2 INSTALLATION INSTRUCTIONS
3 SAFETY PRECAUTIONS
4 PARTS
5 HELPFUL HINTS
6 Attach dividers to center panel.
7 Secure dividers to center panel with screws
8 Push 2 dowels into holes of each top/bottom panel.
9 Attach top/bottom panels.
10 Insert dowels into side panels.
11 Attach side panels with screws. Press on screw covers.
12 OPTIONAL
13 Documents / Resources
13.1 References
14 Related Posts
CLOSETMAID Offset Desktop Organizer
INSTALLATION INSTRUCTIONS
BEFORE BEGINNING
Please read all instructions carefully.
Familiarize yourself with all parts (see “PARTS”) and check quantities.
Follow all safety precautions (see “SAFETY PRECAUTIONS”).
What you will need:
SAFETY PRECAUTIONS
WARNING
This unit contains small parts which could be a choking hazard for small children. Children should be under
adult supervision at all times or serious injury could occur.
Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become
unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.
Do not overload unit. If any shelf, top, or bottom of unit bows or bends, it
is overloaded. The shelf, top, or bottom could collapse and cause serious bodily injury and/or damage to
personal belongings.
Do not climb or step on the unit.
The unit may become unstable and either tip or collapse. Serious bodily injury and/or damage to personal
belongings may occur.
Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings may
occur.
Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause
the unit to tip. Serious bodily injury and/or damage to personal belongings may occur.
Do not stack units. Stacking of units can cause an unsafe tip-over hazard which may • cause serious bodily
injury and/or damage to personal belongings.
Do not hang this unit on the wall. The product structure is not designed for wall • hanging. Serious bodily injury,
damage to personal belongings, and/or damage to the wall may occur.
Follow proper safety procedures when using power tools and ladders.
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops,
wood floors, etc.
PARTS
HELPFUL HINTS
PART IDENTIFICATION
Use “PART IDENTIFICATION” picture (in each step) and exploded view (on previous page) to identify parts!
Look for part letter “stamping” in unfinished edges of part.
Note overall shape of part. Count and locate holes in each part.
FINISHED VS. UNFINISHED
It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note
the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same way. While
assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will
face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.
HAND TIGHTEN SCREWS
We recommend you hand-tighten screws. Use care not to overtighten if using power tools.
Attach dividers to center panel.
STEP 1
NOTE:
Center panel has 4 holes in each side!
Push a dowel into each hole.
Push each divider onto dowels in center panel.
Secure dividers to center panel with screws
STEP 2
NOTE:
Secure each divider with a screw.
Press a screw cover onto each screw head.
Push 2 dowels into holes of each top/bottom panel.
STEP 3
NOTE:
Push a dowel into each hole.
Attach top/bottom panels.
STEP 4
NOTE:
Secure with one screw.
Press a screw cover onto screw head.
Repeat for second top/bottom panel.
Insert dowels into side panels.
STEP 5
NOTE:
Push a dowel into each hole.
Attach side panels with screws. Press on screw covers.
STEP 6
NOTE:
Arrange each side panel so unfinished edge is up. Align dowels in side panel with holes in center panels and
top/bottom panels.
Push each side panel into place. Secure each side panel with three screws. Press a screw cover onto each
screw head.
OPTIONAL
STEP 7
NOTE:
Arrange corner bracket so larger holes face up! Note locations for horizontal and vertical mounting.
Align holes in corner bracket with holes in unfinished edges of top and side panels. Secure each corner bracket
to unit with 4 screws.
STEP 8
IMPORTANT: STUD MOUNT WHENEVER POSSIBLE! FOR STUD MOUNTING: THREAD SCREW DIRECTLY
INTO STUD.FOR CONCRETE MOUNTING: CONTACT HARDWARE STORE FOR APPROPRIATE WALL
MOUNTING HARDWARE.
NOTE:
Hold unit against wall at desired location. Use a level to be sure unit is straight.
Use a pencil to mark the top of the bracket keyhole as shown. Request help, if necessary, to hold the unit in
place.
Set unit aside. Use a 1/4 in. drill bit to drill a hole at each marked location. Push anchors into drilled holes.
Thread screw into anchor. DO NOT FULLY TIGHTEN SCREW!
Place each bracket over screw heads. Tighten screws.
Documents / Resources
CLOSETMAID Offset Desktop Organizer [pdf] Installation Guide
Offset Desktop Organizer, Offset Organizer, Desktop Organizer, Organizer
References
mano.no
ClosetMaid US Online Store | ClosetMaid
Manuals+,
home
privacy
/