JennAir LIB0126461 Owner's manual

Brand: JennAir

Model: LIB0126461

Category: Cooker hoods

Type: Owner's manual

JENNAIR® 30" (76.2 CM) AND 36" (91.4 CM)

WALL-MOUNT CANOPY RANGE HOOD

HOTTE D’EXTRACTION À MONTAGE MURAL DE

30PO (76,2CM) ET 36PO (91,4CM) JENNAIR®

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces,

des accessoires ou du dépannage, composer le :

1800JENNAIR (1800536-6247) ou visiter notre site Web au www.jennair.com.

Au Canada, composer le: 1800JENNAIR (1800536-6247) ou visiter notre site Web au www.jennair.ca.

Table of Contents/Table des matières .....................................2

IMPOR

TANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONL

IMPOR

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISA

TION RÉSIDENTIELLE UNIQUEMENT

LIB0126461/W11160327B

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS .................................................5

Tools and Parts .............................................................................5

Location Requirements ................................................................6

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ...................................................8

Prepare Location ..........................................................................8

RANGE HOOD USE ......................................................................15

Controls ......................................................................................15

RANGE HOOD CARE ...................................................................16

Cleaning .....................................................................................16

WIRING DIAGRAM .......................................................................17

ASSISTANCE OR SERVICE .........................................................18

In the U.S.A. ..............................................................................18

In Canada ...................................................................................18

Accessories ................................................................................18

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE ............................................................19

EXIGENCES D’INSTALLATION ...................................................21

Outils et pièces ...........................................................................21

Exigences d’emplacement .........................................................22

Spécications électriques ..........................................................23

INSTRUCTIONS D’INSTALLATION .............................................24

Préparation de l’emplacement ...................................................24

UTILISATION DE LA HOTTE .......................................................31

Commandes ...............................................................................31

ENTRETIEN DE LA HOTTE .........................................................32

Nettoyage ...................................................................................32

SCHÉMA DE CÂBLAGE ...............................................................33

ASSISTANCE OU DÉPANNAGE ..................................................34

Aux É.-U. ...................................................................................34

Au Canada ..................................................................................34

Accessoires ................................................................................34

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ

AND

SAVE

THESE

INSTRUCTIONS

For General Ventilating Use Only. Do Not Use

To Exhaust Hazardous Or Explosive Materials And Vapors.

This appliance is not intended for use by people (including

children) whose physical, sensory or mental capacities are

different or impaired or who lack the necessary experience

or knowledge/expertise to do so, unless such persons are

supervised or are trained to operate the appliance by a

person who accepts responsibility for their safety.

To Reduce The Risk Of Fire Or Electric

Shock, Do Not Use This Fan With Any Solid-State Speed

Control Device.

Ducted fans must always be vented to the outdoors.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listedhere.

Tools needed:

■Level

■Drill with 11/4" (3.0 cm), 3/16" (5.0 mm) and 6/19" (8.0 mm)

drill bits

■Pencil

■Tape measure or ruler

■Adhesive tape

■Flat-blade screwdriver

■Metal snips

■Phillips screwdriver

■POZI driver

■T20® Torx® bit or driver

Parts needed:

Part Name Qty.

Flexible duct as per

ceiling height;

external diameter

6" (15.2 cm)

(15.2 cm)

Steel duct clamps for

6" (15.2 cm) ducts 2

Parts supplied:

Remove parts from packages. Check that all parts are included.

Part Name Qty.

Hood canopy

assembly with

ventilator and lights

installed

Chimney covers 2

Charcoal lter

mounting bracket 1

Charcoal lter 1

Part Name Qty.

Charcoal lter

clamps 3

Plastic transition 1

Paper template 1

3 prong plug with

connector 1

Wire clamp 1

Ø5 x 45 mm screws 8

Ø8 x 40 mm anchors 8

3.5 x 9.5 mm screws 6

2.9 x 6.5 mm pins 2

Flat washers 3

Cabinet Dimensions

*For non-vented (recirculating) installations

IMPORTANT:

Minimum distance “X”: 24" (61.0 cm) from electric

cookingsurface.

Minimum distance “X”: 30" (76.2 cm) from gas

cookingsurface.

Suggested maximum distance “X”: 36" (91.4 cm)

NOTE: For best performance of the Auto Sense feature, the

range hood should be installed at 24" (61.0 cm) from an electric

cooking surface and 30" (76.2 cm) from a gas cooking surface.

The chimneys can be adjusted for different ceiling heights.

Seethe following chart.

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soft heights depending on the

distance “X” between the bottom of the range hood and the

cooking surface.

Centerline

Side

cabinet Side

cabinet

30" (76.2 cm)

36" (91.4 cm)

“X”

bottom of

canopy

to cooking

surface

Cooking surface

11 / " (30.0 cm)

13 16

/ " (30.0 cm) max.

13 16

19 / " (50.0 cm)

11 16

Product Dimensions

Installation

Min. ceiling height Max. ceiling height

Electric cooking

surface 8' 25/8" (2.50 m) 10' 4" (3.24 m)

Gas cooking

surface 8' 65/8" (2.61 m) 10' 4" (3.24 m)

A. 125/8" (32.1 cm)

B. 1213/16" (32.5 cm)

C. For 30" (76.2 cm) models,

2915/16" (76.0 cm)

For 36" (91.4 cm) models,

3515/16" (91.3 cm)

D. For 30" (76.2 cm) models,

1715/16" (45.6 cm)

For 36" (91.4 cm) models,

1715/16" (45.6 cm)

E. 23/8" (6.0 cm)

F. 24" (61.0 cm)

G. 385/8" (98.1 cm) min.

491/8" (124.8 cm) max.

H. 115/8" (29.5 cm)

I. 12" (30.5 cm)

J. 123/8" (31.4 cm)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualied technician to install the range hood. It is the

installer’s responsibility to comply with installation clearances

specied on the model/serial/rating plate. The model/serial/

rating plate is located behind the left lter on the rear wall of

thevent hood.

Canopy hood location should be away from strong draft

areas,such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

The canopy hood mounting location must be capable

ofsupporting 100 lbs (45.4 kg).

This range hood is recommended for use with cooktops

withamaximum total rating of 68,000 BTUs or less.

Grounded electrical outlet is required. See the “Electrical

Requirements” section.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations:

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A, or latest edition, or

withlocalcodes.

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 V, 60 Hz, AC only, 15 A, fused electrical circuit

isrequired.

For 3 Prong Grounded Power Cord:

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

■This range hood is equipped with a power supply cord

having a 3 prong grounding plug.

■To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

Ifa mating outlet is not available, it is the responsibility of

thecustomer to have the properly grounded outlet installed

by a qualied electrician.

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■ For a grounded, cord-connected range hood:

This range hood must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of electric

shock by providing an escape wire for the electric current.

This range hood is equipped with a cord having a grounding

wire with a grounding plug. The plug must be plugged into

an outlet that is properly installed and grounded.

WARNING: Improper grounding can result in a risk of

electric shock.

Consult a qualified electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the range hood is properly grounded.

Do not use an extension cord. If the power supply cord is too

short, have a qualified electrician install an outlet near the

range hood.

30"

(76.2 cm)

■The grounded 3 prong outlet is to be located above the

range hood at a maximum distance of 30" (76.2 cm) from

where the power cord exits the hood. See illustration.

Electrical Requirements

INSTALLATION INSTRUCTIONS

Prepare Location

■Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect power.

2. Select a at surface for assembling the range hood.

Placecovering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Canopy Installation Preparation

1. Mark centerline on wall

■Determine and mark the centerline on the wall where the

canopy hood will be installed.

Min 24" (61.0 cm) for Electric

Min 30" (76.2 cm) for Gas

Max 36" (91.4 cm)

18¹/₈" (46.0 cm)

2. Tape template to wall

■Tape the template sheet so the lower edge of the sheet

representing the bottom of the hood is at a mounting height

between a minimum of 24" (61.0 cm) for an electric cooking

surface, a minimum of 30" (76.2 cm) for a gas cooking

surface, and a suggested maximum of 36" (91.4 cm) for both

gas and electric cooking surfaces.

⁵/₁₆" (8 mm)

3. Drill pilot holes

■Drill an 5/16" (8 mm) pilot hole per the hole location on the

template sheet.

■Ensure the hole aligns with the centerline drawn.

■Remove the template sheet.

₅"

(5 mm)

4. Install mounting screw

■Install one 8 x 40 mm anchor.

■Install one 5 x 45 mm screw.

■Ensure the screw has at least 1/5" (5 mm) gap to the wall

when screwed in for mounting the hood.

3. Using 2 or more people, lift range hood onto

coveredsurface.

Charcoal Filter Bracket Installation

1. Align charcoal lter bracket

■Remove the charcoal lter bracket from the box and place

it at the desired height above the hood canopy bottom (use

provided template for reference).

■Ensure the center of the bracket is aligned with the center

line marked to conrm the center of the hood aligns with the

center of the lter bracket.

⁵/₁₆" (8 mm)

2. Drill pilot holes

■Mark holes as per center line and drill 2-5/16" (8 mm) holes.

Tip: Use a level tool to ensure the bracket is level before

drilling the holes.

3. Install anchors

■Install 2 anchors and screw the bracket into place.

■Do not fully tighten the screws as the bracket will need to be

removed in the next step.

4. Mark center hole

■Mark the center hole with a pencil.

■Place the charcoal lter bracket back into position so that all

the holes are aligned with the anchors.

■Secure 2 screws on the upper bracket slots and one screw

with a at washer on the lower bracket slot, to secure the

bracket in position.

7. Mount charcoal lter bracket

Prepare for Installation

120 V, 60 Hz

1. Verify electrical outlet location

■Ensure grounded 3 prong outlet capable of 120 V, 60 Hz is

available before proceeding.

■Ensure at least 2/5" (1 cm) gap between bottom of the

charcoal lter bracket to top of the grounded 3 prong outlet.

■Ensure at least 19/50" (3 cm) gap between anchor screw and

the bottom of the grounded 3 prong outlet.

■Ground 3 prong outlet must be 4/5" (2 cm) shorter in width

than the chimney width.

2. Remove grease lter

■Remove grease lters before proceeding.

⁵/₁₆" (8 mm)

6. Drill center hole

■Drill an 5/16" (8 mm) hole where the center hole is marked

and insert 1-5/16" (8 mm) anchor.

5. Remove bracket

■Remove the screws (not the anchors) in order to remove the

bracket.

3. Place hood on mounting screw

■Using 2 or more people, hang the range hood on the

mounting screw through the mounting slot on the back of the

hood.

4. Level hood

■Use a level to ensure the hood is level before proceeding.

5. Mark mounting hole

■Once you have the hood aligned properly, use a pencil to

mark 4 holes as shown in the picture.

6. Remove hood

■Using 2 or more people, remove the hood.

⁵/₁₆" (8 mm)

7. Drill holes

■Drill 4-5/16" (8 mm) holes.

8. Mount range hood

■Using 2 or more people, hang the range hood on the

mounting screw through the mounting slot on the back of the

hood.









9. Secure with screws

■Fasten the hood with 2-5 x 45 mm screws on the top and

2-4 x 45 mm screws with at washers at the bottom as

shown.

Making Electrical Connection

1. Remove tape

■Remove the tape holding the electrical box in the hood.

2. Mount electrical box

■Slide the electrical box onto the screws provided and tighten

it with a at head screwdriver.

Tip: Use a manual driver for this operation.

3. Connect the power cord

■Insert the connector into the slot provided on the electrical

box.

4. Secure power cord

■Using the wire clamp provided, secure the wire as shown.

5. Plug into a grounded 3 prong outlet

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Complete Installation

1. Install plastic transition

■Align the plastic transition to the bottom of the charcoal lter

bracket and fasten it with the 2-2.9 x 6.5 mm screws.

6" (15.2 cm)

2. Install duct

■Slide the duct into place ensuring it is placed over the

exhaust of the hood and over the plastic transition.

■Secure in place with the duct clamps.

NOTE: Use of exible duct is recommended.

4. Install the chimney cover

■Slide the chimney cover into the slot over the canopy and

adjust the height of the chimney as needed.

■Chimney height:

Minimum: 385/8" (98.1 cm)

Maximum: 491/8" (124.8 cm)

Tip: Ensure the hood is connected electrically and working

before assembling the chimney cover.

min 38⁵/₈" (98.1 cm)

max 49¹/₈" (124.8 cm)

5. Secure the chimney to bracket

■Fasten the top of the chimney to the lter bracket with the

screws provided.

6. Reinstall grease lter

■Install the grease lter back into position.

3. Install charcoal lter

■Slide the charcoal lter into place on the bracket as shown.

■Secure the charcoal lter in three locations with the clamps

provided as shown.

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after

the cooking is complete to clear all smoke and odors from the

kitchen.

The range hood controls are located on the front of the canopy.

A. Louver holes (non-vented

[recirculating] installations only)

B. Chimney covers

C. Lamps

D. Filter door

E. Canopy

F. Control panel

RANGE HOOD USE

Timed Fan

Touch the "Timed Fan" keypad to set the automatic shutdown

timer.

Set automatic shutdown timer:

Press one of the following keypads to set the automatic

shutdown of the fan according to desired shutdown time:

1. Quiet Fan: 20 minutes

2. Med fan: 15 minutes

3. Hi Fan: 10 minutes

When the "Timed Fan" keypad ashes, maintenance of the

charcoal lter needs to be completed. Once completed, touch

and hold down the "Fan On-Off" keypad until the ashing stops.

Quiet Fan

Touch the "Quiet Fan" keypad to select the 'silent' fan. This fan

speed provides a subtle fan speed.

When the "Quiet Fan" keypad ashes, maintenance of the

grease lter needs to be completed. Once completed, touch and

hold down the "Fan On-Off" keypad until the ashing stops.

Light On-Off

Touch the "Light On-Off" keypad to turn the hood light on or off.

Automatic operation under high temperature

conditions

The hood is equipped with a sensor which detects the

cooking temperature. When this becomes too high, the sensor

automatically turns on the medium fan speed. The hood turns off

once the temperature has cooled down.

When the "Med Fan", "Hi Fan" and "Timed Fan" keypads ash,

the automatic sensor will turn on.

Activation of the charcoal lter maintenance indicator

This indicator is automatically set to Off. To activate it, proceed

as follows:

With the hood off, press and hold the "Med Fan" and "Hi Fan"

keypads at the same time until both keypads ash.

Deactivation of charcoal lter maintenance indicator

With the hood off, press and hold the "Med Fan" and "Hi Fan"

keypads at the same time until both keypads ash. This is

followed by ashing only "Hi Fan" keypad to indicate successful

deactivation.

Controls

Fan On-Off

Touch the "Fan On-Off" keypad to turn the fan on or off.

Med Fan

Touch the "Med Fan" keypad to turn the fan to medium speed.

Hi Fan

Touch the "Hi Fan" keypad once to turn the fan to high speed.

Touch the "Hi Fan" keypad twice to turn the fan to the highest

fan speed.

NOTE: The highest fan speed lasts for approximately 5 minutes,

then the fan returns to the high fan speed automatically.

Fan

On-Off

Med

Fan

Timed

Fan

Quiet

Fan

Light

On-Off

RANGE HOOD CARE

Cleaning

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool

or soap-lled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■Liquid detergent soap and water, or all-purpose cleanser:

Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Grease Filters

IMPORTANT: Clean the hood and grease lters frequently

according to the following instructions. Replace grease lters

before operating hood.

Clean once a month (or when the lter saturation indication

system indicates it necessary) using non aggressive detergents,

either by hand or in the dishwasher, which must be set to a low

temperature and a short cycle.

When washed in a dishwasher, the grease lter may discolor

slightly, but this does not affect its ltering capacity.

To remove the grease lter, pull the spring release handle.

Charcoal Filter

It absorbs unpleasant odors caused by cooking.

The efciency of the charcoal lter degrades slowly due to

prolonged use, depending on the type of cooking, and the

regularity of cleaning the grease lter.

Replace the cartridge at least every ve years.

It cannot be washed.

For maximum performance, the lter is larger than standard

lters and needs to be installed on a support above the hood.

Installation:

Place the charcoal lter into the charcoal lter mounting bracket.

Install the charcoal lter clamps in the locations shown.

NOTE: The opening of the charcoal lter should be placed facing

down towards the hood.

NOTE: When used in recirculation mode, To Reduce the Risk of

Fire and Shock use only conversion kit Model W11197817.

Replacing LED Lights

The hood is equipped with a lighting system based on LED

technology.

To purchase spare LEDs, see the "Assistance or Service"

section.

NOTE: Lights can be replaced by service technician only.

WIRING DIAGRAM

ASSISTANCE OR SERVICE

If you need service:

Please refer to the warranty page in this manual.

If you need replacement parts:

If you need to order replacement parts, we recommend that

you use only factory specied parts. Factory specied parts will

t right and work right because they are made with the same

precision used to build every new appliance.

To locate factory specied replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call JennAir Customer eXperience Center toll free:

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■Scheduling of service. JennAir® appliances designated

service technicians are trained to fulll the product

warrantyand provide after-warranty service anywhere

intheUnited States.

■Features and specications on our full line of appliances.

■Referrals to local JennAir® appliance dealers.

■Installation information.

■Use and maintenance procedures.

■Accessory and repair parts sales.

■Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance:

If you need further assistance, you can write to JennAir®

Appliances with any questions or concerns at:

JennAir Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free at 1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■Scheduling of service. JennAir® appliances designated

service technicians are trained to fulll the product warranty

and provide after-warranty service anywhere in Canada.

■Features and specications on our full line of appliances.

■Referrals to local JennAir® appliance dealers.

■Installation information.

■Use and maintenance procedures.

■Accessory and repair parts sales.

For further assistance:

If you need further assistance, you can write to JennAir®

Appliances with any questions or concerns at:

JennAir Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

Order Part Number W11197817

SÉCURITÉ DE LA HOTTE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

Avertissements de la proposition 65 de l'État de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

malformations et autres déficiences de naissance.

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE

BLESSURES, RESPECTER LES INSTRUCTIONS

SUIVANTES :

■ Utiliser cet appareil uniquement selon les modalités

d’utilisation prévues par le fabricant. Pour toute question,

contacter le fabricant.

■ Avant d’entreprendre une opération d’entretien ou de

nettoyage sur l’appareil, interrompre l’alimentation de

l’appareil au panneau de distribution et verrouiller ce dernier

pour empêcher tout rétablissement accidentel de

l’alimentation du circuit. Lorsqu’il n’est pas possible de

verrouiller le tableau de distribution, placer sur ce dernier

une étiquette d’avertissement bien en vue interdisant le

rétablissement de l’alimentation.

■ Tout travail d’installation ou câblage électrique doit être

réalisé par une personne qualifiée, dans le respect des

prescriptions de tous les codes et toutes les normes

applicables, y compris les codes du bâtiment et de

protection contre les incendies.

■ Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommagé. Jeter le ventilateur ou le retourner à

un centre de service agréé pour examen ou réparation.

■ Une source d’air de débit suffisant est nécessaire pour que

la combustion et l’évacuation des gaz puissent s’effectuer

correctement par la cheminée de l’appareil à gaz, afin

d’éviter tout reflux des gaz de combustion. Respecter les

directives du fabricant de l’équipement de chauffage et les

prescriptions des normes de sécurité – comme celles

publiées par la National Fire Protection Association (NFPA)

et l’American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), ainsi que les

prescriptions des autorités réglementaires locales.

■ Lors des opérations de découpage et de perçage dans un

mur ou un plafond, ne pas endommager les câblages

électriques et les canalisations qui peuvent s’y trouver.

■ Les ventilateurs d’évacuation doivent toujours décharger

l’air vers l’extérieur.

MISE EN GARDE : Cet appareil est conçu uniquement

pour la ventilation générale. Ne pas l’utiliser pour

l’extraction de matières ou vapeurs dangereuses ou

explosives.

MISE EN GARDE : Pour réduire le risque d’incendie et

évacuer adéquatement les gaz, acheminer l’air aspiré par

un conduit jusqu’à l’extérieur – ne pas décharger l’air aspiré

dans un espace vide du bâtiment comme une cavité

murale, un plafond, un grenier, un vide sanitaire ou un

garage.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D’INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MÉTALLIQUES.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D’UN

FEU DE GRAISSE SUR LA CUISINIÈRE :

■ Ne jamais laisser un élément de surface fonctionner à

puissance maximale sans surveillance.Un

renversement/débordement de matière graisseuse peut

provoquer des flammes et générer de la fumée. Chauffer

l’huile à une puissance moyenne ou basse.

■ Veiller à toujours faire fonctionner le ventilateur de la hotte

lors de la cuisson avec une puissance élevée ou lors de la

cuisson d’un mets à flamber (à savoir crêpes Suzette,

cerises jubilées, steak au poivre flambé).

■ Nettoyer fréquemment le ventilateur d’extraction. Veiller à

ne pas laisser la graisse s’accumuler sur les surfaces du

ventilateur ou des filtres.

■ Utiliser toujours un ustensile de taille appropriée. Utiliser

toujours un ustensile adapté à la taille de l’élément

chauffant.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE DE

BLESSURES APRÈS LE DÉCLENCHEMENT D’UN FEU DE

GRAISSE SUR LA CUISINIÈRE, RESPECTER LES

RECOMMANDATIONS SUIVANTESa:

■ Placer sur le récipient un couvercle bien ajusté, une tôle à

biscuits ou un plateau métallique POUR ÉTOUFFER LES

FLAMMES, puis éteindre le brûleur. VEILLER À ÉVITER

LES BRÛLURES. Si les flammes ne s’éteignent pas

immédiatement, ÉVACUER LA PIÈCE ET APPELER LES

POMPIERS.

■ NE JAMAIS PRENDRE EN MAIN UN RÉCIPIENT

ENFLAMMÉ – Vous risquez de vous brûler.

■ NE PAS UTILISER D’EAU ni de torchon humide – ceci

pourrait provoquer une explosion de vapeur brûlante.

■ Utiliser un extincteur SEULEMENT si :

– Il s’agit d’un extincteur de classe ABC, dont on connaît le

fonctionnement.

– Il s’agit d’un petit feu encore limité à l’endroit où il s’est

déclaré.

– Les pompiers ont été contactés.

– Il est possible de garder le dos orienté vers une sortie

pendant l’opération de lutte contre le feu.

aRecommandations tirées des conseils de sécurité en cas

d'incendie de cuisine publiés par la NFPA.

■ AVERTISSEMENT : Pour réduire le risque d’incendie

ou de décharge électrique, ne pas utiliser ce ventilateur

avec un dispositif de réglage de la vitesse à

semi-conducteurs.

Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) dont les capacités

physiques, sensorielles ou mentales sont différentes ou

réduites ou qui ne possèdent pas l’expérience, les connais-

sances ou l’expertise nécessaire, à moins d’être super-

visées ou d’avoir reçu des instructions concernant l’utilisa-

tion par une personne responsable de leur sécurité.

Page is loading ...

JennAir LIB0126461 Owner's manual

Brand: JennAir

Model: LIB0126461

Category: Cooker hoods

Type: Owner's manual

Download PDF

report

in other languages

français: JennAir LIB0126461 Le manuel du propriétaire

JennAir LIB0126461 Owner's manual

JennAir LIB0126461 Owner's manual

in other languages

Related papers

Other documents