Dimplex 26 Inch Optiflame LED Electronic Firebox Operating instructions

Brand: Dimplex

Model: 26 Inch Optiflame LED Electronic Firebox

Category: Fireplaces

Type: Operating instructions

The Dimplex 26 Inch Optiflame LED Electronic Firebox offers a range of features for creating a cozy and inviting atmosphere in your home. Enjoy the comforting effects of the flame with or without heat, thanks to the flame effect that operates independently. With adjustable brightness levels and a demo mode, you can customize the flames to your preference. Additionally, the pulsating and static log effects add depth and realism to the firebox. This versatile appliance also includes a top light that can be turned on or off, providing additional ambiance.

26” FIREBOX

08/53613/2 (EU) Issue 1

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2

and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC

A B C D E F G H

585mm

680mm

229mm

4 5

6 7

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to

ensure that they do not play with

the appliance.

Children shall not plug in, regulate or

clean the appliance or perform any

user maintenance.

The appliance must be positioned so that

the plug is accessible.

Although this appliance complies with

safety standards, we do not recommend

its use on deep pile carpets or on long

hair type of rugs.

If the supply cord is damaged it must be

Do not use this heater with a

programmer, timer, separate remote-

control system or any other device that

switches the heater on automatically,

since a fire risk exists if the heater is

covered or positioned incorrectly.

Important Safety Advice

When using electrical appliances, basic

precautions should be followed to

reduce the risk of re, electric shock, and

injury to persons, including the following:

If the appliance is damaged, check

immediately with the supplier before

installation and operation.

Do not use this appliance in the

immediate surroundings of a bath,

shower or swimming pool.

Do not use outdoors.

This appliance must not be located

immediately above or below a fixed

socket outlet or connection box.

WARNING: The appliance carries

the Warning Symbol indicating that

it must not be covered or has a Do

not cover label. Do not cover or

obstruct in any way the heat outlet

grille located above the ame window

on the appliance Overheating will result

if the appliance is accidentally covered.

Do not place material or garments on the

appliance, or obstruct the air circulation

around the appliance, for instance by

curtains or furniture, as this could cause

overheating and a re risk.

In the event of a fault unplug the heater.

Unplug the appliance when not required

for long periods. The supply cord must

be placed on the right hand side of

the heater away from the heat outlet

underneath the appliance.

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

replaced by the manufacturer or service

agent or similarly qualified person in

order to avoid a hazard.

CAUTION: In order to avoid a hazard due

to inadvertent resetting of the thermal

cut-out, this appliance must not be

supplied through an external switching

device, such as a timer, or connected

to a circuit that is regularly switched on

and off by the utility.

CAUTION - Some parts of this product

can become very hot and cause burns.

Particular attention has to be given

where children and vulnerable people

are present.

Technical Information

Model No: DF2608-LED

Heat Output 230V 240V

Nominal Heat Output P Nom 1.9 - 2.0 kW

Minimum Heat Output P min 0.9 - 1.0 kW

Maximum Continuous Heat Output P max,c 1.9 - 2.0 kW

Auxiliary Electricity Consumption

In Standby mode el SB 0.41 - 0.42 W

with electronic room temperature control

General

Unpack the heater carefully and retain the packaging for

possible future use, in the event of moving or returning the

re to your supplier.

The re incorporates a ame effect, which can be used

with or without heating, so that the comforting effect may

be enjoyed at any time of the year. Using the ame effect

on its own only requires little electricity.

Before connecting the heater check that the supply

voltage is the same as that stated on the heater.

Please note: Used in an environment where background

noise is very low, it may be possible to hear a sound which

is related to the operation of the ame effect. This is normal

and should not be a cause for concern.

Electrical Connection

WARNING: THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the

voltage marked on the heater must correspond to the

supply voltage.

Before switching on, please read the safety warnings and

operating instructions.

Controls: See Fig. 3

Icon Display Function Description

A-Power /

Standby

Press once to turn the product ‘ON’.

Press a second time to put the product into ‘STANDBY’

(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product

has been plugged out, in which case it will reset to factory settings)

BSleep

Timer

Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning

off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)

Flame Effect ‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,

DEMO MODE and OFF.

Low

Flame

This setting will run the ame effect at a low brightness level. (The display will show F1)

High

Flame

This setting will run the ame effect at a high brightness level. (The display will show F2)

Demo

Mode

This setting will slowly pulse the ame effect between low and high brightness. (The display will show

FP)

- Off This will turn the ame effect off. If the heater is running, the display will activate and remain active to

read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.

Log Effect ‘LOG EFFECT’ button cycles the unit sequentially through the 3 setting, ‘PULSING LOGS, STATIC LOGS

and OFF.

Pulsing

Logs

This setting will make the logs pulse. (The display will show FP)

Static

Logs

This setting will make the logs stay lit. (The display will show FS)

- Off This setting will turn the logs off.

E- On / Off

This button cycles the top light ‘On’ and ‘Off’.

Heat

‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW

and OFF. The heat setting will be indicated by an icon in the oating display see Fig.1.

When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however if the heater is

being used independently of the ame effect. The low heat or high heat icon will appear continuously

in the oating display.

Low Heat

This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon

and the letters ‘LO’ appearing in the display.

(This icon is Orange in Colour)

High

Heat

This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’

icon and the letters ‘HI’ appearing in the display.

(This icon is Red in Colour)

Cool

Blow

This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL

BLOW’ icon and the letters ‘CB’ appearing in the display.

(This icon is Blue in Colour)

- Off This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display. Note the

blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.

G-Temp

Down

Press multiple times to lower the heater temperature in 1°C increments. The lowest temperature that

can be set 5°C.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

H- Temp Up

Press multiple times to increase the heater temperature in 1°C increments. The highest temperature

that can be set 37°C.

Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the

room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

User Modes:

Mode Name /Description Action (Actions cannot be input by remote control)

Change Celsius (° C) to Fahrenheit (° F) Press both Temp+ ( ) and Temp– ( ) on the unit and hold until beep is heard and

display flashes. (To revert back to Celsius repeat this action)

Disable/Enable Heat Options Hold both Heat ( ) and Temp– ( ), on the unit, for 2 seconds, when the heater has

been disabled the display will read “--” and beep. To enable heat repeat this action.

New Wall Construction

1. Select a suitable location that is not susceptible to

moisture and is away from drapes, furniture and high

trafc.

2. Place the replace in the desired location to see how

it will look in the room.

3. Mark the desired location on the oor.

4. Use studs to frame an opening of 680 mm wide X 585

mm high X 229 mm deep.(DF2608) Use studs to frame an

opening of 775 mm wide X 654mm high X 298 mm deep.

(DF3020)

Option #1

The power cord can be run from behind the trim and

along the wall to an outlet near the replace.

Option #2

A new outlet can be installed inside the framing

construction. Plug the replace into a 10-13Amp/230-

240 Volt outlet. If the cord does not reach you may use

a 3-core type extension cord rated for a minimum of

10 Amps.

Existing Fireplace

1. Seal all drafts and vents with a non-brous insulation

material to prevent any chimney debris from falling onto

the replace. Do not install into an existing replace that

is prone to dampness.

2. Cap the top of the chimney ue to prevent rain from

entering.

3. Plan your electric power supply.

4. The power cord can run along the front of the hearth

to an outlet near the replace.

Thermal Safety Cut-out

The built-in overheat cut-out, switches off the appliance

automatically in the event of a fault! Should this occur

switch off the appliance or disconnect the mains plug

from the socket.

Remove any obstructions which may have caused the

overheating. After a short cooling down phase, the

appliance is ready for use again! If the fault should occur

again, contact your local dealer!

WARNING: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched

on and off by the utility.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Light Emitting Diode

This re is tted with LED (Light Emitting Diode) lamps. These

LED lamps are maintenance-free and should not require

replacing during the life of the product.

Remote Control - See Fig. 3

The maximum range of use is ~ 5metres.

NOTE: It takes time for the receiver to respond to the

transmitter.

NOTE: The receiver for the remote control is located in

the display, aim the remote control in this direction when

inputting commands.

Do not press the buttons more than once within two

seconds for correct operation.

Battery Information - See Fig. 3

1. To activate the remote control remove the clear battery

isolation strip at the base of the remote control, which

is used to ensure your remote control reaches you fully

charged.

2. To replace the remote control battery, turn over the

remote control, and follow the diagram embossed on the

remote control

3. Only use CR2025 or CR2032 size of batteries.

Installing Front Glass- See Fig. 5, 6 & 7

NOTE: The outer glass is shipped separate to the rebox.

1. Remove the three screws holding the side trim as shown

in Fig. 5. and remove the metal trim.

2. Unpack the glass, ensure it is free from dust and nger

marks and slide in to position as shown in Fig. 6.

3. Position the metal trim removed in step 1, and secure

with the three screws as per Fig. 7

Fitting- See Fig. 4

IMPORTANT: If not using a Dimplex mantel, the replace

must be installed in an enclosure with the following

MINIMUM dimensions(Figure 4).

1. Select a suitable location that is not susceptible to

moisture and is at least 1 meter away from drapes,

furniture and high trafc.

2. Store the replace in a safe, dry and dust free location.

3. Clearance for air circulation beneath the replace

is provided by two spacers. DO NOT INSTALL FIREPLACE

DIRECTLY ON CARPET OR SIMILAR SURFACES WHICH MAY

RESTRICT AIR CIRCULATION. If installing the replace in

a carpeted area, place a one-piece, solid at surface

under the replace. Ensure that all feet rest securely on

this surface!

4. In some jurisdictions this appliance is supplied without

a plug this is to comply with the local regulations. In such

instances this appliance must be installed by a suitably

qualified installer and the means for disconnection must

be incorporated in the fixed wiring in accordance with

the local wiring rules.

Cleaning

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY

BEFORE CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use

abrasive cleaners. The glass viewing screen should be

cleaned carefully with a soft cloth.

DO NOT use proprietary glass cleaners.

To remove any accumulation of dust or uff the soft brush

attachment of a vacuum cleaner should occasionally be

used to clean the outlet grille of the fan heater.

WARNING: do not operate the product without the grille

and outer glass in position as this may effect the operation

of the heater.

Recycling

For electrical products sold within the European

Community. At the end of the electrical

products useful life it should not be disposed

of with household waste. Please recycle where

facilities exist. Check with your Local Authority

or retailer for recycling advice in your country.

After Sales Service

Should you require after sales service or should you need

to purchase any spares, please contact the retailer from

whom the appliance was purchased or contact the service

number relevant to your country on the warranty card.

Please do not return a faulty product to us in the rst instance

as this may result in loss or damage and delay in providing

you with a satisfactory service. Please retain your receipt

as proof of purchase.

Dimplex 26 Inch Optiflame LED Electronic Firebox Operating instructions

Brand: Dimplex

Model: 26 Inch Optiflame LED Electronic Firebox

Category: Fireplaces

Type: Operating instructions

Download PDF

report

Dimplex 26 Inch Optiflame LED Electronic Firebox Operating instructions

Dimplex 26 Inch Optiflame LED Electronic Firebox Operating instructions

Related papers

Other documents