Lightology P472 Wall Mount Fixture User manual

Brand
Lightology
Model
P472 Wall Mount Fixture
Type
User manual
INSTALLATION INSTRUCTIONS
Item#P472 (Rev. 03/01/2012)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUI T BRE AKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and remove
the old fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
3. Attach mounting plate (A) to the junction box with mounting
screws (B) (Size: #8-32N*L0.5”).
CONNECTING THE WIRES (Fig. 2)
4. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the circular strap using
the green screw provided.
FINISHING THE INSTALLATION (Fig.1)
5. Align fixture body (D) to mounting plate (A) and secure it with
screws (C).
6. Place shade (E) over the socket and level horizontally.
7. Install light bulbs (not included) in accordance with
fixture specifications, (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Your installation is now complete. Return power and
test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2147E
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY
A QUALIFIED ELECTRICIAN TO ENSURE PROPER
WIRING AND INSTALLATION.
D
A
B
C
E
INSTALLATION INSTRUCTIONS FOR P472
-X-L
For Wall Mount Fixture
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R .
PREPARATION
1. Shut off power at the fuse box or circuit breaker box. If
necessary. Remove the old fixture and mounting
hardware.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Take care not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (FIG. 1)
3. Secure mounting back plate (A) to the outlet box
using junction box screws (B) (Size: 8-32*1/2”L). The
side of the mounting back plate marked “GND” must
face out.
CONNECTING THE WIRES (FIG. 2)
4. At this point, connect the electrical wires as shown in
Fig. 2, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or
bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to
the mounting plate (A) using the green screw
provided. After wires are connected, tuck them
carefully inside the junction box.
5. Align fixture’s back plate (C) onto mounting back plate
(A) and secure with screws (D) (Size 'M4*8MM).
FINISHING THE INSTALLATION (FIG.1)
6. Align diffuser (F) followed by gaskets (O), onto
bracket (I) and secure with screws (G). The clear side
diffuser (F) should face down toward bracket (I).
7. Align cloth shade (H) (PS472) onto back plate (C) and
secure with screws (E)
CAUTION/ATTENTION:
When handling the fixture, do
not apply pressure to the LEDs. Hold the fixture by the
base or front bracket (I) only.
IMPORTANT:
Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified
electrician without cutting of wire and without damage to
any decorative element to which the fixture is attached.
See installation steps for more details (Fig 3.)
a. Shut off the power.
b. Remove screws (E) and cloth shade (H) from back
plate (C).
c. Remove screws (D) and carefully separate the fixture
from mounting back plate (A).
d. Remove the wire nuts (L) located inside the fixture
back plate to disconnect the LED module.
e. Remove screws (J) from mounting plate (A).
f. Remove screws (K) on heat sink (N). Carefully
remove the LED module (M) from the heat sink (N),
g. Reverse steps b-f for installing the new LED module.
h. Note: The LED module should be provided by a
specified supplier.
i. For better heat dissipation the LED module (M)
should be applied with thermal grease when
re
-
lampin
g
.
Fig.2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
Fig.3
FIG.1
IMPORTANT:
Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall
dimmer switches
.
  • Page 1 1
  • Page 2 2

Lightology P472 Wall Mount Fixture User manual

Brand
Lightology
Model
P472 Wall Mount Fixture
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents