Guardian 1" Gate Carabiner Operating instructions

Guardian
Brand
Guardian
Model
1" Gate Carabiner
Type
Operating instructions

This manual is also suitable for

Guardian 1" Gate Carabiner

The Guardian 1" Gate Carabiner is a versatile and durable connector hardware component designed for use in fall protection systems. It features a double-locking mechanism for added security and a wide gate opening for easy attachment to various connection points.

With a minimum breaking strength of 5,000 lbs. on the major axis and 3,600 lbs. on the gate, this carabiner is suitable for heavy-duty applications. It is compliant with OSHA 1926 Subpart M, OSHA 1910, ANSI A10.32-2012, and ANSI Z359.12-2009 standards, ensuring compliance with industry regulations.

The carabiner is constructed from lightweight aluminum, making it easy to carry and maneuver. It is resistant to corrosion, rust, and wear, ensuring longevity even in harsh environments.

Guardian 1" Gate Carabiner

The Guardian 1" Gate Carabiner is a versatile and durable connector hardware component designed for use in fall protection systems. It features a double-locking mechanism for added security and a wide gate opening for easy attachment to various connection points.

With a minimum breaking strength of 5,000 lbs. on the major axis and 3,600 lbs. on the gate, this carabiner is suitable for heavy-duty applications. It is compliant with OSHA 1926 Subpart M, OSHA 1910, ANSI A10.32-2012, and ANSI Z359.12-2009 standards, ensuring compliance with industry regulations.

The carabiner is constructed from lightweight aluminum, making it easy to carry and maneuver. It is resistant to corrosion, rust, and wear, ensuring longevity even in harsh environments.

Connector Hardware
Part #s:
USER MUST READ AND UNDERSTAND ALL INSTRUCTIONS PRIOR TO USE.
Compliant with OSHA 1926 Subpart M, OSHA 1910, ANSI A10.32-2012, and ANSI Z359.12-2009.
Ensure that all connections are selected and deemed compatible with applicable Connector Hardware
by a Competent Person.
MINIMUM breaking strength, primary axis: 5,000 lbs.
MINIMUM breaking strength, gate: 3,600 lbs.
All Guardian Fall Protection Connector Hardware is marked with the following information:
When not in use, store Connector Hardware in a location absent of all potential hazards, including, but
not limited to, heat, light, excessive moisture, corrosive substances, dirt, and other contaminants.
Before and after each use, clean all Connector Hardware. If equipment cannot be wiped clean, use mild
soap and water, then rinse, wipe, and hang to dry. NEVER use bleach or other corrosive cleaning agents.
• Load rating for major axis of connector: 5,000 lbs. and/or 22 kN.
• Load rating for gate: 3,600 lbs. and/or 16 kN.
• Manufacturer’s identification.
• Serial number or batch number.
• Year of manufacture.
01850
Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com
01817 01825 01830 018370183501822-A 01823 01823-A
Always adhere to product-specific instructions for safe and compatible connections of Connector
Hardware to fall protection equipment.
Connector Hardware Component Details:
Inspect Connector Hardware prior to EACH use. Inspect for all damage including, but not limited to,
corrosion, rust, wear, warping, alteration, pits, burrs, and absence of markings. All Connector Hardware
MUST be self-closing and self-locking. If Connector Hardware fails any inspection criteria, or any other
damage is found or suspected, IMMEDIATELY remove Connector Hardware from service.
Installation/Use:
1. Push and hold gate-
release lever.
2. Push on gate, connect hook,
and release gate.
Snap Hook
!
WARNING
Prior to use, ALWAYS test to ensure Connector Hardware gate is fully closed and locked to connection
point. Never make incompatible connections. Large throat hooks must NEVER be connected to
standard size D-rings or similar connection points that may result in a load on the gate if the hook
or D-ring twists or rotates. Large throat hooks are designed for use on fixed structural elements, such
as rebar or cross members. Never install hook in location where potential exists for simultaneous
impact of gate and release mechanism; doing so may result in accidental roll-out.
Pompier Hook / Carabiner
1. Twist gate
and hold.
2. Push gate, connect
hook, release gate.
If triple locking,
lift gate,
then twist and push.
Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: (800) 466-6385 fax: (800) 670-7892 www.guardianfall.com
85054 (Rev. F)
Part #
01817
Gate Description Weight (lbs.)
01830
01850
.75”
.75”
2.25”
Double-Locking Aluminum Carabiner
Double-Locking Stamped Steel Snap Hook
Double-Locking Forged Steel Pompier Hook
0.20
1.20
0.80
2.00
01825 .75”
Double-Locking Steel Swivel Snap Hook
01837 .75”
Double-Locking Steel Carabiner
0.50
01822-A
01823
01823-A
01835
Double-Locking Aluminum Snap Hook
1.00”
Double-Locking Steel Rebar Hook
Double-Locking Aluminum Rebar Hook
.75”
Triple-Locking Forged Steel Carabiner 0.60
1.69
2.50”
2.25”
0.67
0.39
  • Page 1 1
  • Page 2 2

Guardian 1" Gate Carabiner Operating instructions

Guardian
Brand
Guardian
Model
1" Gate Carabiner
Type
Operating instructions
This manual is also suitable for

Guardian 1" Gate Carabiner

The Guardian 1" Gate Carabiner is a versatile and durable connector hardware component designed for use in fall protection systems. It features a double-locking mechanism for added security and a wide gate opening for easy attachment to various connection points.

With a minimum breaking strength of 5,000 lbs. on the major axis and 3,600 lbs. on the gate, this carabiner is suitable for heavy-duty applications. It is compliant with OSHA 1926 Subpart M, OSHA 1910, ANSI A10.32-2012, and ANSI Z359.12-2009 standards, ensuring compliance with industry regulations.

The carabiner is constructed from lightweight aluminum, making it easy to carry and maneuver. It is resistant to corrosion, rust, and wear, ensuring longevity even in harsh environments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents