Horizon Fitness CE4.4 Owner's manual

Page is loading ...

3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL. When using an electrical product, basic precautions

should always be followed, including the following: Read all instructions before using this elliptical. It is the responsibility of

the owner to ensure that all users of this elliptical are adequately informed of all warnings and precautions. If you have any

questions after reading this guide, contact Customer Tech Support at the number listed on the back panel.

This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional

setting. Failure to comply will void the warranty.

4

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the elliptical from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or

taking off parts.

DANGER

• To reduce the risk of burns, fire, electrical shock or injury to persons:

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop

exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace. Do not sprint above 80 RPMs on this machine.

• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting

the machine.

• Do not turn pedal arms by hand.

• Make sure handlebars are secure before each use.

• Keep the topside of the foot support clean and dry.

• Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on

the mounting or dismounting side to its lowest position and bring the machine to a complete stop.

• Do not wear clothes that might catch on any part of the elliptical.

• Always wear athletic shoes while using this equipment.

• Do not jump on the elliptical.

• At no time should more than one person be on the elliptical while in operation.

• This elliptical should not be used by persons weighing more than the specified user capacity in the OWNER’S MANUAL

WARRANTY SECTION. Failure to comply will void the warranty.

• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional

setting. Failure to comply will void the warranty.

• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages, porches, pool

rooms, bathrooms, car ports or outdoors. Failure to comply will void the warranty.

• To prevent electrical shock, never drop or insert any object into any opening.

• Connect this exercise product to a properly grounded outlet only.

WARNING

5

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Use the elliptical only as described in the elliptical guide and owner’s manual.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp

cloth only; never use solvents. (See MAINTENANCE)

• The elliptical should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or

taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• At NO time should children under the age of 13 or pets be within 10 feet of the machine.

• At NO time should children under the age of 13 use the elliptical.

• Children over the age of 13 or disabled persons should not use the elliptical without adult supervision.

• Never operate the elliptical if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,

or immersed in water. Contact tech support at the number on the back panel to schedule service.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an

authorized service technician

It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed

to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room

temperature before first time use. Failure to do so may cause premature electronic failure.

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Page is loading ...

7

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the

assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed

correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To

prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your elliptical’s serial number located on a white barcode

sticker on the front stabilizer tube and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

WARNING

SERIAL NUMBER:

EP

MODEL NAME: HORIZON   ELLIPTICAL

SERIAL NUMBER LOCATION

8

UPPER HANDLEBAR

SPEAKERS

PULSE GRIPS

WATER BOTTLE HOLDER

PEDAL ARM

LOWER HANDLEBAR

LOWER LINK ARM

PIVOTING FOOT PADS

REAR STABILIZER

READING RACK

CONSOLE

CONSOLE MAST

TOP CAP

MAIN FRAME

CRANK

POWER CORD SOCKET

STABILIZER TUBE

GUIDE RAIL SET

9

TOOLS REQUIRED:

F 8 mm L-Wrench

F 13/17 mm Flat Wrench

F 5 mm L-Wrench/Screwdriver

F Screwdriver (not included)

PARTS INCLUDED:

F 1 Main Frame

F 1 Stabilizer Tube

F 1 Guide Rail Set

F 1 Console Mast

F 2 Pedal Arms

F 2 Lower Handlebars

F 2 Upper Handlebars

F 2 Handlebar Cover Sets

F 2 Lower Link Arms With Footpads

F 1 Front Top Cap Piece

F 1 Rear Top Cap Piece

F 1 Console

F 1 Audio Adapter Cable

F 1 Power Cord

F 1 Hardware Kit

UNPACKING

Unpack the product where you will be using it. Place the elliptical carton on a

level flat surface. It is recommended that you place a protective covering on

your floor. Never open box when it is on its side.

If you have questions or if there are any missing parts, contact Customer

Tech Support. Contact information is located on the back panel of this

manual.

NEED HELP?

PRE ASSEMBLY

• It is recommended that two people work together for ease and efficiency

while assembling an elliptical.

• During each assembly step, ensure that ALL nuts and bolts are in

place and partially threaded. It is recommended you complete the full

assembly of your unit before completely tightening any ONE bolt.

• Several parts have been pre-lubricated to aid in assembly and usage.

Please do not wipe this off. If you have difficulty, a light application of

lithium bike grease is recommended.

IMPORTANT NOTES

10

ASSEMBLY STEP 1

A Open HARDWARE FOR STEP 1.

B Attach the STABILIZER TUBE (1) to the

MAIN FRAME (2) using 2 BOLTS (A),

2 SPRING WASHERS (B) and 2 ARC

WASHERS (C) on each side.

A

B

C

2

1

HARDWARE FOR STEP 1

PART TYPE DESCRIPTION QTY

A BUTTON HEAD BOLT M8X1.25PX30L 4

B SPRING WASHER 8.2X15.4X2.0T 4

C ARC WASHER 8.4X17.0X1.0T 4

11

HARDWARE FOR STEP 2

PART TYPE DESCRIPTION QTY

D SOCKET CAP BOLT M10X1.5PX20L 4

E SPRING WASHER 10.2X18.4X2.5T 4

F FLAT WASHER 10.2X20.0X1.5T 4

ASSEMBLY STEP 2

3

2

E

F

D

A Open HARDWARE FOR STEP 2.

B Align GUIDE RAIL SET (3) with MAIN

FRAME (2) as shown.

C Attach the GUIDE RAIL SET (3) to the

MAIN FRAME (2) using 4 BOLTS (D),

4 SPRING WASHERS (E) and 4 FLAT

WASHERS (F).

12

2

6

4

8

I

J

B

7

5

H

G

NOTE: Be

careful not

to pinch any

wires while

attaching the

console mast.

ASSEMBLY STEP 3

A Open HARDWARE FOR STEP 3.

B Remove PRE-INSTALLED BOLTS AND

WASHERS (6) from MAIN FRAME (2).

C Carefully pull the CONSOLE CABLE (4) through

the CONSOLE MAST (5) using the twist tie

located inside the CONSOLE MAST (5).

D Attach CONSOLE MAST (5) to MAIN FRAME (2)

using PRE-INSTALLED BOLTS AND WASHERS

(6).

E Slide WAVY WASHER (G) and FLAT WASHER

(H) over CRANK (7) followed by PEDAL ARM (8)

as shown. Rest pedal arm wheel on guide rail.

F Attach the PEDAL ARM (8) to the CRANK (7)

using 1 FLAT WASHER (I), 1 SPRING WASHER

(B) and 1 BOLT (J).

G Repeat steps E–F on the opposite side of the

elliptical.

HARDWARE FOR STEP 3

PART TYPE DESCRIPTION QTY

G WAVY WASHER 17.2X22.5X0.5T 2

H FLAT WASHER 16.0X25.0X1.0T 2

I FLAT WASHER 8.2X30.0X1.5T 2

B SPRING WASHER 8.2X15.4X2.0T 2

J BUTTON HEAD BOLT M8X1.25PX15L 2

13

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

K FLAT WASHER 20.2X27.2X1.5T 4

L WAVY WASHER 20.7X29.1X0.5T 2

I FLAT WASHER 8.2X20.0X1.5T 2

B SPRING WASHER 8.2X15.4X2.0T 2

J BUTTON HEAD BOLT M8X1.25PX20L 2

ASSEMBLY STEP 4

9

10

K

L

K

I

B

J

A Open HARDWARE FOR STEP 4.

B Slide 1 FLAT WASHER (K), 1 WAVY

WASHER (L) and another FLAT

WASHER (K) onto the LOWER LINK ARM

(9).

C Slide the LOWER LINK ARM (9) into the

PEDAL ARM BRACKET (10).

D Attach the LOWER LINK ARM (9)

to the PEDAL ARM BRACKET (10)

using 1 FLAT WASHER (I), 1 SPRING

WASHER (B) and 1 BOLT (J).

E Repeat steps B–D on the opposite side of

the elliptical.

14

H

G

H

I

B

5

12

J

ASSEMBLY STEP 5

A Open HARDWARE FOR STEP 6.

B Slide 1 FLAT WASHER (H), 1 WAVY WASHER

(G) and 1 FLAT WASHER (H) onto the

CONSOLE MAST (5).

C Slide LOWER HANDLEBAR (12) onto

CONSOLE MAST (5) and attach using 1 FLAT

WASHER (I), 1 SPRING WASHER (B) and 1

BOLT (J).

D Repeat steps B–C on the other side.

HARDWARE FOR STEP 5

PART TYPE DESCRIPTION QTY

G WAVY WASHER 17.2X22.5X0.5T 2

H FLAT WASHER 16.0X25.0X1.0T 4

I FLAT WASHER 8.2X30.0X1.5T 2

B SPRING WASHER 8.2X15.4X2.0T 2

J BUTTON HEAD BOLT M8X1.25PX20L 2

15

HARDWARE FOR STEP 6

PART TYPE DESCRIPTION QTY

K BOLT M8X1.25PX70L-12L 2

B SPRING WASHER 8.2X15.4X2.0T 2

I FLAT WASHER 8.2X20.0X1.5T 2

L NUT M8X1.25P 2

ASSEMBLY STEP 6

12

I

B

9

K

L

A Open HARDWARE BAG 6.

B Slide LOWER LINK ARM (9) into bottom end of

LOWER HANDLEBAR (12).

C Secure the joint with 1 BOLT (K), 1 SPRING

WASHER (B),1 FLAT WASHER (I) and 1

NUT (L).

D Repeat steps B–C on the opposite side of

the elliptical.

16

ASSEMBLY STEP 7

13

14

15

12

M

15

A Open HARDWARE BAG 7.

B Slide the right (R) UPPER HANDLEBAR

(13) onto the right LOWER HANDLEBAR

(12) making sure handlebars are joined

together completely. Secure the UPPER

HANDLEBAR (13) to the LOWER

HANDLEBAR (12) using PRE-ATTACHED

SET SCREWS (14).

C Slide right (R) HANDLEBAR COVERS (15)

over UPPER HANDLEBARS (13) and attach

using 1 SCREW (M).

D Repeat STEPS B–C on left side.

HARDWARE FOR STEP 7

PART TYPE DESCRIPTION QTY

M SCREW M4X0.7PX8L 4

NOTE: Make sure upper handlebars are as far

down as possible. Handlebars can be damaged

If not secured correctly.

17

4

16

19

5

17

18

ASSEMBLY STEP 8

ASSEMBLY COMPLETE!

NOTE: All hardware for this step is pre-installed.

A Remove 4 PRE-INSTALLED BOLTS (16) from

the CONSOLE (17).

B Attach the CONSOLE CABLES (4) to the

CONSOLE (17).

C Carefully tuck the CONSOLE CABLES (4)

into the CONSOLE MAST (5) before attaching

the CONSOLE. Attach CONSOLE (17) to

CONSOLE MAST (5) using 4 PRE-INSTALLED

BOLTS (16).

D Slide FRONT TOP CAP PIECE (18) and REAR

TOP CAP PIECE (19) over CONSOLE MAST

(5) and snap into place.

NOTE:

Do not to pinch any wires while attaching the console.

Page is loading ...

19

ELLIPTICAL OPERATION

This section explains how to use your elliptical’s console and programming.

The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:

• LOCATION OF THE ELLIPTICAL

• POWER/GROUNDING INSTRUCTIONS

• FOOT POSITIONING

• MOVING THE ELLIPTICAL

• LEVELING THE ELLIPTICAL

• POWER/MANUAL INCLINE OPERATION

• USING THE HEART RATE FUNCTION

20

3 41 2 5 6 7 8 9 10

resistance resistance

speedheart rate

calorieswattsdistancetime RPM

start

pause

stop

hold to reset

change

display

C

A

L

M

I I

E

J K

D

F

G

B

H

21

CONSOLE OPERATION

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LCD DISPLAY WINDOW: time, RPM, distance, watts, calories, heart rate, speed

B) ENERGY SAVER INDICATOR: indicates if the machine is in energy saver mode.

C) QUICK KEYS: used to reach desired resistance quickly.

D)

KEYS: Used to adjust resistance level and to cycle through selections during program set up.

E) ENTER: used to confirm selection.

F) START / PAUSE: used to start workout, pause workout, and restart after pause.

G) STOP / HOLD TO RESET: used to stop machine and also will reset machine when held down.

H) CHANGE DISPLAY: used to change display feedback during workout.

I) SPEAKERS: plays music through speakers when connected to your media player.

J) AUDIO IN JACK: plug your media player into the console using the included audio adaptor cable.

K) AUDIO OUT JACK: plug your headphones into the console to use during workout.

L) READING RACK: holds reading material.

M) STORAGE POCKET: holds personal items, such as a small TV remote, mobile phone or media player.

22

DISPLAY WINDOW

• TIME: Shown as minutes : seconds. View the time remaining or the time elapsed in your workout.

• DISTANCE: Shown as miles. Indicates distance traveled during your workout.

• CALORIES: Total calories burned or remaining for your workout.

• RPM: Revolutions Per Minute.

• WATTS: Displays current user power output

• SPEED: Shown as MPH. Indicates how fast the foot pads is moving.

• HEART RATE: Shown as BPM (beats per minute). Used to monitor your heart rate (displayed when

contact is made with both pulse grips).

• PROGRAM PROFILES: Represents the profile of the program being used.

• ENERGY SAVER: Indicates when machine is in Energy Saver mode to conserve power consumption.

speedheart rate

calorieswattsdistancetime RPM

23

FINISHING YOUR WORKOUT

When your workout is complete, the console

will display “workout complete” and beep. Your

workout information will stay displayed on the

console for 30 seconds and then reset.

TO RESET THE CONSOLE

Hold STOP key for 3 seconds.

TO CLEAR CURRENT SELECTION

To clear the current program selection or screen,

hold the stop button for 3 seconds.

GETTING STARTED

1) Check to make sure no objects are nearby that will hinder

the movement of the elliptical.

2) Plug in the power cord to power the elliptical ON. (Switch is

located at the bottom-front of the elliptical.)

3) Set User Weight using

and press ENTER.

4) You have the following options to start your workout:

A) QUICK START UP

Simply press GO to begin working out.

Time, distance and calories will all count up from zero.

The resistance level will default to level 1.

B) SELECT A PROGRAM

1) Use

to scroll through programs

2) Press ENTER to select your desired program.

3) Set workout level using

and press ENTER.

4) Press START to begin workout.

NOTE: You can adjust the resistance level during your workout.

24

PROGRAM INFORMATION

MANUAL: Adjust your resistance level manually during your workout.

WEIGHT LOSS: Promotes weight loss by raising and lowering the resistance level, while keeping you in your fat

burning zone. Time based program with 10 levels to choose from.

WEIGHT LOSS PLUS: Promotes weight loss by raising and lowering the resistance level, while keeping you in your

fat burning zone. Time based program with 5 levels to choose from and greater intensity than the weight loss program.

INTERVALS: Improves your strength, speed and endurance by raising and lowering the resistance levels through-out

your workout to involve both your heart and muscles. Time based program with 10 levels to choose from.

INTERVALS PLUS: Improves your strength, speed and endurance by raising and lowering the resistance levels

through-out your workout to involve both your heart and muscles. Time based program with 5 levels to choose from

and greater intensity than the intervals program.

CONSTANT WATTS: User sets a watts level and tries to maintain that level throughout the workout. Resistance will

adjust automatically to keep the user at the correct watts level. Time based program.

ROLLING: Mimics the feeling of moving up and down hills by gradually increasing and decreasing the resistance.

Time based program with 7 levels to choose from.

REVERSE TRAIN: Program cues you to pedal forward (F) and backwards (R) for an exciting and challenging workout.

RANDOM: Provides even more workout variety by mixing up your resistance levels. Time based program with 7 levels

to choose from.

CALORIE GOAL: Allows you to set the number of calories you would like to burn. Calorie goal can range from 100-

990 calories. Calories will count down. User inputs weight and sets starting resistance. Calories burned are calculated

using weight input with the speed and incline of the workout.

Page is loading ...

Horizon Fitness CE4.4 Owner's manual

This manual is also suitable for

Horizon Fitness CE4.4 Owner's manual

in other languages

Related papers

Other documents