2. Ubiquiti
  3. PAK-620

Ubiquiti PAK-620 Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Ubiquiti PAK-620 Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Precision Alignment Kit for
620 mm Dish Reflector
Model: PAK-620
Introduction
Thank you for purchasing the Ubiquiti Networks® Precision
Alignment Kit, which is compatible with the following:
• airFiber®AF‑5G30‑S45
• PowerBeam™ PBE‑5AC‑620
• PowerBeamPBE‑M5‑620
• RocketDish™ RD‑5G30‑LW
Package Contents
Alignment Bracket
Assembly
Pole Clamps
(Qty. 2)
Carriage Bolts
(M8x150, Qty. 4)
Precision Alignment Kit for
620 mm Dish Reflector
Model: PAK-620
Serrated Flange Nuts
(M8, Qty. 4)
Hex Head Bolts
(M8, Qty. 4)
Quick Start
Guide
Installation Requirement
• 13 mm Wrench
Hardware Overview
Azimuth
Alignment Bracket
Elevation
Alignment Bracket
Azimuth
Adjustment
Screw
Elevation
Adjustment
Screw
Alignment Bracket Assembly after Separation of Brackets
Elevation
Lever
Installation
The following instructions show the RD‑5G30‑LW; however,
they also apply to other antennas that use 620 mm dish
reflectors.
1. Loosen the four hex head bolts of the Alignment Bracket
Assembly.
2. Lift the Elevation Alignment Bracket up and out to separate
it from the Azimuth Alignment Bracket.
*640-00177-01*
640-00177-01
3. Use four Hex Head Bolts to attach the Elevation Alignment
Bracket to the antenna. Ensure that the Hex Head Bolts
go through the Elevation Levers on the inner sides of the
Elevation Alignment Bracket.
4. Attach two Pole Clamps to the Azimuth Alignment Bracket.
a. Insert four Carriage Bolts into the Azimuth Alignment
Bracket.
b. Slide the hole of a Pole Clamp over one bolt of each pair.
c. Place one Serrated Flange Nut on each bolt.
5. Attach the Azimuth Alignment Bracket to the pole:
a. Slide the slot of each Pole Clamp over the
corresponding CarriageBolt.
b. Tighten the four Serrated Flange Nuts to secure the
Azimuth Alignment Bracket to the pole.
6. Attach the Elevation Alignment Bracket to the Azimuth
Alignment Bracket:
a. Insert the four hex head bolts of the Elevation Alignment
Bracket into the slots of the Azimuth Alignment Bracket.
b. Slide the Elevation Alignment Bracket down, and tighten
the four hex head bolts to 25 N‑m.
25 N-m
7. Before adjusting the azimuth and elevation angles, ensure
that these eight hex head bolts are loose enough to allow
movement.
8. To adjust the azimuth angle up to ±15°, turn the Azimuth
Adjustment Screw until the desired angle is reached.
Azimuth Adjustment Screw
9. To adjust the elevation angle up to ±15°, turn the Elevation
Adjustment Screw until the desired angle is reached.
Elevation
Adjustment Screw
10. Lock the alignment by tightening the eight hex head bolts
to 25 N‑m.
©2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the
Ubiquiti U logo, the Ubiquiti beam logo, airFiber, PowerBeam, and RocketDish
are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United
States and in other countries. All other trademarks are the property of their
respective owners. JL051815
/