Gigabyte Z490M GAMING X Owner's manual

Brand: Gigabyte

Model: Z490M GAMING X

Type: Owner's manual

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

For more product details, please visit GIGABYTE's website.

Z490M GAMING X

User's Manual

Rev. 1002

12ME-Z490MGX-1002R

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE

without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any

form or by any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

Z490M GAMING X Motherboard Layout .........................................................................4

Chapter 1 Hardware Installation .....................................................................................5

1-1 Installation Precautions .................................................................................... 5

1-2 ProductSpecications ...................................................................................... 6

1-3 Installing the CPU ............................................................................................ 9

1-4 Installing the Memory ..................................................................................... 10

1-5 Installing an Expansion Card ......................................................................... 10

1-6 Back Panel Connectors .................................................................................. 11

1-7 Internal Connectors ........................................................................................ 13

Chapter 2 BIOS Setup ..................................................................................................22

2-1 Startup Screen ............................................................................................... 22

2-2 The Main Menu .............................................................................................. 23

2-3 Favorites (F11) ............................................................................................... 24

2-4 Tweaker .......................................................................................................... 25

2-5 Settings .......................................................................................................... 30

2-6 System Info. ................................................................................................... 36

2-7 Boot ................................................................................................................ 37

2-8 Save & Exit ..................................................................................................... 40

Chapter 3 Appendix ......................................................................................................41

3-1 ConguringaRAIDSet .................................................................................. 41

3-2 Installing an Intel® Optane™ Memory .............................................................. 43

3-3 DriversInstallation .......................................................................................... 45

RegulatoryNotices .................................................................................................... 46

Contact Us ................................................................................................................ 48

- 4 -

Z490M GAMING X Motherboard Layout

* The box contents above are for reference only and the actual items shall depend on the product package you

obtain. The box contents are subject to change without notice.

Box Contents

5Z490M GAMING X motherboard 5User's Manual

5Motherboard driver disc 5Two SATA cables

KB_MS_U32

DP_HDMI

U32_LAN

LGA1200 ATX

AUDIO

ATX_12V_2X4

Intel® Z490

CLR_CMOS

M_BIOS

PCIEX1

PCIEX4

PCIEX16

F_U32

M2A_SB

M2Q_CPU (Note)

CODEC Z490M GAMING X

F_PANEL

F_USB1

D_LED1

LED_C2

QFLASH_PLUSTHB_CF_AUDIO

D_LED2

COMSPDIF_O

SYS_FAN3

F_USB2 SPI_TPM

LED_C1

SYS_FAN1

SYS_FAN2

CPU_FAN

iTE®

Super I/O

4260

6080

110

SATA3SATA3 3 2

1 0

BAT

Intel®

GbE LAN

U32_G2

U32_G2C

THB_C1

ATX_12V_2X2

QFLED

DDR4_A1

DDR4_A2

DDR4_B1

DDR4_B2

(Note) The M.2 connector is reserved only. No functionalities.

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damagedasaresultofelectrostaticdischarge(ESD).Priortoinstallation,carefullyreadtheuser's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

componentssuchasamotherboard,CPUormemory.IfyoudonothaveanESDwriststrap,

keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Donotplacethecomputersystemonanunevensurface.

•Donotplacethecomputersysteminahigh-temperatureorwetenvironment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 5 -

1-2 ProductSpecications

CPU Support for 10th Generation

Intel® Core™ i9 processors/Intel® Core™ i7 processors/Intel® Core™ i5 processors/

Intel® Core™ i3 processors/Intel® Pentium® processors/Intel® Celeron® processors

in the LGA1200 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® Z490 Express Chipset

Memory 4xDDR4DIMMsocketssupportingupto128GB(32GBsingleDIMMcapacity)

of system memory

Dualchannelmemoryarchitecture

SupportforDDR43200/2933/2666/2400/2133MHzmemorymodules

* Tosupport3200MHz,youmustuseXMPmemory.

SupportforECCUn-bufferedDIMM1Rx8/2Rx8memorymodules(operatein

non-ECC mode)

Supportfornon-ECCUn-bufferedDIMM1Rx8/2Rx8/1Rx16memorymodules

SupportforExtremeMemoryProle(XMP)memorymodules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel®HDGraphicssupport:

- 1xDisplayPort,supportingamaximumresolutionof4096x2304@60Hz

* SupportforDisplayPort1.4version,HDCP2.3,andHDR.

- 1xHDMIport,supportingamaximumresolutionof4096x2160@30Hz

* SupportforHDMI1.4versionandHDCP2.3.

Maximum shared memory of 512 MB

Audio Realtek® ALC1200 codec

HighDenitionAudio

2/4/5.1/7.1-channel

SupportforS/PDIFOut

LAN Intel® GbE LAN chip (1000 Mbit/100 Mbit)

Expansion Slots 1 x PCI Express x16 slot, running at x16 (PCIEX16)

* For optimum performance, if only one PCI Express graphics card is to be installed,

be sure to install it in the PCIEX16 slot.

1 x PCI Express x16 slot, running at x4 (PCIEX4)

1 x PCI Express x1 slot

(All of the PCI Express slots conform to PCI Express 3.0 standard.)

Multi-Graphics

Technology SupportforAMDQuad-GPUCrossFire™and2-WayAMDCrossFire™ technologies

Storage Interface  1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 SATA and PCIe

x4/x2SSDsupport)(M2A_SB)

6 x SATA 6Gb/s connectors

SupportforRAID0,RAID1,RAID5,andRAID10

* Referto"1-7InternalConnectors,"fortheinstallationnoticesfortheM.2andSATA

connectors.

Intel® Optane™MemoryReady

- 6 -

USB Chipset:

- 1 x USB Type-C™ port on the back panel, with USB 3.2 Gen 2 support

- 1 x USB 3.2 Gen 2 Type-A port (red) on the back panel

- 6 x USB 3.2 Gen 1 ports (4 ports on the back panel, 2 ports available through

the internal USB header)

- 4 x USB 2.0/1.1 ports available through the internal USB headers

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 4-pin ATX 12V power connector

1 x 8-pin ATX 12V power connector

1 x CPU fan header

3 x system fan headers

2xaddressableLEDstripheaders

2xRGBLEDstripheaders

6 x SATA 6Gb/s connectors

1 x M.2 Socket 3 connector

1 x front panel header

1 x front panel audio header

1xS/PDIFOutheader

1 x USB 3.2 Gen 1 header

2 x USB 2.0/1.1 headers

2 x Thunderbolt™ add-in card connectors

 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI

2.0 module only)

1 x serial port header

1 x Clear CMOS jumper

1 x Q-Flash Plus button

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

4 x USB 3.2 Gen 1 ports

1xDisplayPort

1xHDMIport

1 x USB 3.2 Gen 2 Type-A port (red)

1 x USB Type-C™ port, with USB 3.2 Gen 2 support

1xRJ-45port

6 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan speed control function is supported will depend on the cooler you

install.

- 7 -

BIOS 1x256Mbitash

Use of licensed AMI UEFI BIOS

PnP1.0a,DMI2.7,WfM2.0,SMBIOS2.7,ACPI5.0

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functionsofeachapplicationmayalsovarydependingonmotherboardspecications.

- @BIOS

- EasyTune

- Fast Boot

- Game Boost

- ON/OFF Charge

- RGBFusion

- Smart Backup

- System Information Viewer

Support for Q-Flash Plus

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton® Internet Security (OEM version)

cFosSpeed

Operating

System Support for Windows 10 64-bit

Form Factor Micro ATX Form Factor; 24.4cm x 24.4cm

* GIGABYTEreservestherighttomakeanychangestotheproductspecicationsandproduct-relatedinformationwithout

prior notice.

Please visit GIGABYTE's website

for support lists of CPU, memory

modules,SSDs,andM.2devices.

Please visit the Support\Utility List

page on GIGABYTE's website to

download the latest version of apps.

- 8 -

1-3 Installing the CPU

ReadthefollowingguidelinesbeforeyoubegintoinstalltheCPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•DonotturnonthecomputeriftheCPUcoolerisnotinstalled,otherwiseoverheatinganddamage

of the CPU may occur.

•SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended

thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications,pleasedosoaccordingtoyourhardwarespecicationsincludingtheCPU,graphics

card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Please visit GIGABYTE's website for details on hardware installation.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically during the process of re-engaging the lever after you insert the CPU.

Triangle Pin One Marking on the CPU

NotchNotch

LGA1200 CPU

Alignment KeyAlignment Key

LGA1200 CPU Socket

Pin One Corner of the CPU Socket

- 9 -

DualChannelMemoryConguration

ThismotherboardprovidesfourmemorysocketsandsupportsDualChannelTechnology.Afterthememory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.EnablingDual

Channel memory mode will double the original memory bandwidth.

The four memory sockets are divided into two channels and each channel has two memory sockets as following:

ChannelA:DDR4_A1,DDR4_A2

ChannelB:DDR4_B1,DDR4_B2

DuetoCPUlimitations,readthefollowingguidelinesbeforeinstallingthememoryinDualChannelmode.

1. DualChannelmodecannotbeenabledifonlyonememorymoduleisinstalled.

2. WhenenablingDualChannelmodewithtwoorfourmemorymodules,itisrecommendedthatmemory

of the same capacity, brand, speed, and chips be used.

1-5 Installing an Expansion Card

Readthefollowingguidelinesbeforeyoubegintoinstallanexpansioncard:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

RecommandedDualChannelMemoryConguration:

DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

2 Modules - - DS/SS - - DS/SS

4 Modules DS/SS DS/SS DS/SS DS/SS

(SS=Single-Sided,DS=Double-Sided,"--"=NoMemory)

1-4 Installing the Memory

Readthefollowingguidelinesbeforeyoubegintoinstallthememory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

- 10 -

ActivityLED

Connection/

SpeedLED

LAN Port

ActivityLED:Connection/SpeedLED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Datatransmissionorreceivingisoccurring

On No data transmission or receiving is occurring

USB 3.2 Gen 2 Type-A Port (Red)

TheUSB3.2Gen2Type-AportsupportstheUSB3.2Gen2specicationandiscompatibletotheUSB

3.2Gen1andUSB2.0specication.UsethisportforUSBdevices.

USB Type-C™ Port

ThereversibleUSBportsupportstheUSB3.2Gen2specicationandiscompatibletotheUSB3.2Gen1

andUSB2.0specication.UsethisportforUSBdevices.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describesthestatesoftheLANportLEDs.

AfterinstallingtheDisplayPort/HDMIdevice,makesuretosetthedefaultsoundplaybackdeviceto

DisplayPort/HDMI.(Theitemnamemaydifferdependingonyouroperatingsystem.)

1-6 Back Panel Connectors

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

USB 3.2 Gen 1 Port

TheUSB3.2Gen1portsupportstheUSB3.2Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.

DisplayPort

DisplayPortdelivershighqualitydigitalimagingandaudio,supportingbi-directionalaudiotransmission.

DisplayPortcansupportbothDPCPandHDCP2.3contentprotectionmechanisms.Itprovidesimproved

visualssupporting Rec. 2020 (WideColor Gamut) andHigh Dynamic Range (HDR)for Blu-ray UHD

playback.YoucanusethisporttoconnectyourDisplayPort-supportedmonitor.Note:TheDisplayPort

Technologycansupportamaximumresolutionof4096x2304@60Hzbuttheactualresolutionssupported

depend on the monitor being used.

HDMI Port

TheHDMI port supportsHDCP2.3 and DolbyTrueHDand DTS HD Master

Audioformats. It also supports up to 192KHz/16bit 7.1-channel LPCM audio

output.YoucanusethisporttoconnectyourHDMI-supportedmonitor.Themaximumsupported

resolutionis4096x2160@30Hz, but the actual resolutionssupportedaredependenton the monitor

being used.

- 11 -

PleasevisitGIGABYTE'swebsitefordetailsonconguringtheaudiosoftware.

AudioJackCongurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Center/Subwoofer Speaker Out a a

RearSpeakerOut aaa

Side Speaker Out a

Line In

Line Out/Front Speaker Out a a a a

Mic In

USB 3.2 Gen 1 Type-A Port (Q-Flash Plus Port)

TheUSB3.2Gen1portsupportstheUSB3.2Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.BeforeusingQ-FlashPlus(Note), make sure to insert the USB

ashdriveintothisportrst.

Center/Subwoofer Speaker Out (Orange)

Use this audio jack to connect center/subwoofer speakers.

Rear Speaker Out (Black)

Use this audio jack to connect rear speakers.

Side Speaker Out (Gray)

Use this audio jack to connect side speakers.

Line In (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out (Green)

The line out jack.

Mic In (Pink)

The Mic in jack.

•Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

•Whenremovingthecable,pullitstraightoutfromtheconnector.Donotrockitsidetosideto

prevent an electrical short inside the cable connector.

(Note) ToenabletheQ-FlashPlusfunctionpleasevisit the"UniqueFeatures" webpageofGIGABYTE's

website.

- 12 -

1-7 Internal Connectors

Readthefollowingguidelinesbeforeconnectingexternaldevices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

4 98

510 14

114

15 12 13

3 5

1) ATX_12V_2X2/ATX_12V_2X4

2) ATX

3) CPU_FAN

4) SYS_FAN1/2/3

5) LED_C1/LED_C2

6) D_LED1/D_LED2

7) SATA3 0/1/2/3/4/5

8) M2A_SB

9) F_PANEL

10) F_ AUDIO

11) F_U32

12) F_USB1/F_USB2

13) SPI_TPM

14) THB_C/THB_C1

15) COM

16) BAT

17) CLR_CMOS

18) QFLASH_PLUS

19) SPDIF_O

- 13 -

1/2) ATX_12V_2X2/ATX_12V_2X4/ATX (2x2, 2x4, 12V Power Connectors and 2x12 Main Power

Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

DEBUG

PORT

G.QBOFM

131

ATX

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5GND 17 GND

6 +5V 18 GND

7GND 19 GND

8 Power Good 20 NC

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin ATX) 23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin ATX) 24 GND(Onlyfor2x12-pinATX)

ATX_12V_2X4:

Pin No. Denition Pin No. Denition

1GND(Onlyfor2x4-pin12V) 5+12V (Only for 2x4-pin 12V)

2GND(Onlyfor2x4-pin12V) 6+12V (Only for 2x4-pin 12V)

3GND 7 +12V

4GND 8 +12V

DEBUG

PORT

G.QBOFM

ATX_12V_2X4

ATX_12V_2X2:

Pin No. Denition

1GND

2GND

3 +12V

4 +12V

ATX_12V_2X2

3 4

- 14 -

5) LED_C1/LED_C2 (RGB LED Strip Headers)

 Theheaderscanbeusedtoconnectastandard5050RGBLEDstrip(12V/G/R/B),withmaximumpower

rating of 2A (12V) and maximum length of 2m.

Pin No. Denition

1 12V

2 G

4 B

LED_C1 LED_C2

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

3/4) CPU_FAN/SYS_FAN1/2/3 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.

CPU_FAN/SYS_FAN1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SYS_FAN2

SYS_FAN3

DEBUG

PORT

G.QBOFM

Pin No. Denition

1GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

Forhowtoturnon/offthelightsoftheLEDstrippleasevisitthe"UniqueFeatures"webpageof

GIGABYTE's website.

ConnectyourRGBLEDstriptotheheader.Thepowerpin(marked

withatriangleontheplug)oftheLEDstripmustbeconnectedto

Pin 1 (12V) of this header. Incorrect connection may lead to the

damageoftheLEDstrip.

RGB

LEDStrip

12V

- 15 -

DEBUG

PORT

G.QBOFM

7) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel®ChipsetsupportsRAID0,

RAID1,RAID5,andRAID10.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguring

aRAIDarray.

Pin No. Denition

1GND

2 TXP

3 TXN

4GND

5RXN

6RXP

7GND

Toenablehot-pluggingfortheSATAports,refertoChapter2,"BIOSSetup,""Settings\IOPorts\

SATAAndRSTConguration,"formoreinformation.

SATA3

2 0

3 1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

6) D_LED1/D_LED2 (Addressable LED Strip Headers)

 Theheaderscanbeusedtoconnectastandard5050addressableLEDstrip,withmaximumpowerrating

of5A(5V)andmaximumnumberof1000LEDs.

Pin No. Denition

1 V (5V)

3 No Pin

4 G

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

Forhowtoturnon/offthelightsoftheLEDstrippleasevisitthe"UniqueFeatures"webpageof

GIGABYTE's website.

Connectyour addressable LED strip to the header.The power pin

(markedwithatriangleontheplug)oftheLEDstripmustbeconnected

toPin1oftheaddressableLEDstripheader.Incorrectconnectionmay

leadtothedamageoftheLEDstrip.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

D_LED1 D_LED2

AddressableLED

Strip

- 16 -

Installation Notices for the M.2 and SATA Connectors:

The availability of the SATA connectors may be affected by the type of device installed in the M.2 connector.

Refertothefollowingtablesfordetails.

•M2A_SB:

SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5

M.2SATASSD ara a a a

M.2PCIeSSD

a a a a a a

NoM.2SSDInstalled a a a a a a

a: Available, r: Not available

Connector

Type of

M.2SSD

8) M2A_SB (M.2 Socket 3 Connector)

 TheM.2connectorssupportM.2SATASSDsorM.2PCIeSSDsandsupportRAIDconguration.Please

notethatanM.2PCIeSSDcannotbeusedtocreateaRAIDseteitherwithanM.2SATASSDoraSATA

harddrive.TocreateaRAIDarraywithanM.2PCIeSSD,youmustsetupthecongurationinUEFIBIOS

mode.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguringaRAIDarray.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

80110 60 42

FollowthestepsbelowtocorrectlyinstallanM.2SSDintheM.2connector.

Step 1:

LocatetheM.2connectorwhereyouwillinstalltheM.2SSD,useascrewdrivertounfastenthescrewon

the heatsink and then remove the heatsink.

Step 2:

LocatethepropermountingholebasedonthelengthofyourM.2SSDdrive.Ifneeded,movethestandoff

tothedesiredmountinghole.InserttheM.2SSDintotheM.2connectoratanangle.

Step 3:

PresstheM.2SSDdownandthensecureitwiththescrew.Replacetheheatsinkandsecureittotheoriginal

hole.Makesuretoremovetheprotectivelmfromthebottomoftheheatsinkbeforereplacingtheheatsink.

M2A_SB

- 17 -

10) F_AUDIO (Front Panel Audio Header)

 ThefrontpanelaudioheadersupportsHighDenitionaudio(HD).Youmayconnectyourchassisfront

panel audio module to this header. Make sure the wire assignments of the module connector match the

pin assignments of the motherboard header. Incorrect connection between the module connector and the

motherboard header will make the device unable to work or even damage it.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

9 1

10 2

Pin No. Denition Pin No. Denition

1 MIC2_L 6 Sense

2GND 7FAUDIO_JD

3MIC2_R 8 No Pin

4 NC 9 LINE2_L

5LINE2_R 10 Sense

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

resetswitch,powerLED,harddriveactivityLED,speakerandetc.Whenconnectingyourchassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

9) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW(PowerSwitch,Red):

Connects to the power switch on the chassis front panel. You may

congure the way to turn off your system using thepower switch

(refertoChapter2,"BIOSSetup,""Settings\PlatformPower,"formore

information).

•SPEAK (Speaker, Orange):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (PowerLED,Yellow/Purple):

Connects to the power status indicator

onthechassisfrontpanel.TheLEDison

whenthesystemisoperating.TheLEDis

off when the system is in S3/S4 sleep state

or powered off (S5).

•HD (HardDriveActivityLED,Blue):

 ConnectstotheharddriveactivityLEDonthechassisfrontpanel.TheLEDisonwhentheharddrive

is reading or writing data.

•RES (ResetSwitch,Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

ifthecomputerfreezesandfailstoperformanormalrestart.

•CI (Chassis Intrusion Header, Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has

been removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC (Orange): No Connection.

PowerLED

DEBUG

PORT

G.QBOFM

CI-

CI+

PWR_LED-

PWR_LED+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

PowerLED

HD-

RES+

HD+

RES-

HardDrive

ActivityLED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

PWR_LED-

- 18 -

Pin No. Denition Pin No. Denition Pin No. Denition

1 VBUS 8 D1- 15 SSTX2-

2SSRX1- 9D1+ 16 GND

3SSRX1+ 10 NC 17 SSRX2+

4GND 11 D2+ 18 SSRX2-

5 SSTX1- 12 D2- 19 VBUS

6 SSTX1+ 13 GND 20 No Pin

7GND 14 SSTX2+

11) F_U32 (USB 3.2 Gen 1 Header)

 TheheaderconformstoUSB3.2Gen1andUSB2.0specicationandcanprovidetwoUSBports.For

purchasingtheoptional3.5"frontpanelthatprovidestwoUSB3.2Gen1ports,pleasecontactthelocal

dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

20 1

12) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

 TheheadersconformtoUSB2.0/1.1specication.EachUSBheadercanprovidetwoUSBportsviaan

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1 Power (5V) 6 USBDY+

2 Power (5V) 7 GND

3USBDX- 8GND

4USBDY- 9 No Pin

5USBDX+ 10 NC

•DonotplugtheIEEE1394bracket(2x5-pin)cableintotheUSB2.0/1.1header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

DEBUG

PORT

G.QBOFM

13) SPI_TPM (Trusted Platform Module Header)

You may connect an SPI TPM (Trusted Platform Module) to this header.

Pin No. Denition Pin No. Denition

1DataOutput 7Chip Select

2Power (3.3V) 8GND

3No Pin 9IRQ

4NC 10 NC

5DataInput 11 NC

6CLK 12 RST

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

- 19 -

15) COM (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

Pin No. Denition Pin No. Denition

1NDCD- 6NDSR-

2 NSIN 7 NRTS-

3 NSOUT 8 NCTS-

4NDTR- 9NRI-

5GND 10 No Pin

14) THB_C/THB_C1 (Thunderbolt™ Add-in Card Connectors)

The connectors are used to connect to a GIGABYTE Thunderbolt™ add-in card.

Supports a Thunderbolt™ add-in card.

16) BAT (Battery)

 Thebatteryprovidespowertokeepthevalues(suchasBIOScongurations,date,andtimeinformation)

intheCMOSwhenthecomputeristurnedoff.Replacethebatterywhenthebatteryvoltagedropstoalow

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or use

a metal object like a screwdriver to touch the positive and negative terminals of the

battery holder, making them short for 5 seconds.)

3. Replacethebattery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replacethebatterywithanequivalentone.Damagetoyourdevicesmayoccurifthebattery

is replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself

or uncertain about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-)

of the battery (the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

THB_C

THB_C1

- 20 -

Page is loading ...

Gigabyte Z490M GAMING X Owner's manual

Brand: Gigabyte

Model: Z490M GAMING X

Type: Owner's manual

Download PDF

report

in other languages

italiano: Gigabyte Z490M GAMING X Manuale del proprietario

Gigabyte Z490M GAMING X Owner's manual

Gigabyte Z490M GAMING X Owner's manual

in other languages

Related papers