OPTIMUM
MASCHINEN - GERMANY
© 2006
GB
1
2 / 01 / 2006 Version 1.0 MSR 4 Material stand
Operating manual
Version 1.0
MSR 4
Material stand
Keep for future reference!
OPTIMUM
MASCHINEN - GERMANY
© 2006 GB
2Material stand MSR 4 Version 1.0 2 / 01 / 2006
1 Proper use
The material stand serves as a manual help to feed or as a support for long parts on metal belt
saws or other machines. The maximun load of the material stand amounts to 360 kg.
2 Safety advices
WARNING!
Before using the material stand, make sure
- that no persons are endangered,
- that no material is being damaged.
Avoid any working method which might endanger the safety:
• Always make sure that the maximum load of the material stand is not exceeded.
• Make sure that no one is endangered by your work.
• Imparatively follow the instructions of this operating manual for the operation and mainte-
nance work.
• Follow the regulations for the prevention of occupationals accidents of the employer’s liablility
insurance association of your company or of any other supervising authority.
• Always make sure that no persons are endanged if the workpiece gets off-center or if it is fal-
ling down.
• Repairs on the material stand must only be performed by specialist staff.
• Wear safety shoes.
3 Technical data
Material stand
Support roller diameter mm ¢ 60
Support roller width mm 360
Width of the material stand mm 440
Length of the material stand mm 1000
Height of the material stand mm 650-950
Weight kg 30
Max. load kg 360
OPTIMUM
MASCHINEN - GERMANY
© 2006
GB
3
2 / 01 / 2006 Version 1.0 MSR 4 Material stand
4Operation
4.1 Safety
Only commission the material stand under the following conditions:
The material stand is used as intended
The operating manual is being followed
4.2 Hight-adjustable material stand
To be able to adjust the height of the material stand:
• Loosen the cap screws with an adequate key.
• Adjust the to the required height .
• Re-fasten the cap screws with an appropriate key.
CAUTION!
Make sure that the pillars with the
cap screws of the height-adjusta-
ble material stand are firmly bolted
before using the material stand.
Otherwise, the positioning of the
stands would no longer be guaran-
teed in case of loading.
Fig.4-1: material stand
5 Dimensions
1
2 3
1
2
3
1
2
1
OPTIMUM
MASCHINEN - GERMANY
© 2006 GB
4Material stand MSR 4 Version 1.0 2 / 01 / 2006
6 Spare part drawing
6.1 Spare part list
1
3
4
5
6
7
2
8
9
10 11
12
13
14
15
16
17
No Designation Size pcs Item No
1stand ¢ 80 mm 4 033576101
2 threaded rod M16x80 4 033576102
3 set screw M5x10 4 033576103
4 counternut M16 4 033576104
5 steel tube ¢ 52 mm 4 033576105
6 cap screw M8x20 8 033576106
7 pillar 2 033576107
8 hexagon screw M8 8 033576108
9diskDIN ISO
7089 8 033576109
10 U-profile 80x40 2 0335761010
11 hexagon screw M8 8 0335761011
12 hexagon nut M12 8 0335761012
13 disk DIN ISO
7089 8 0335761013
14 locking ring DIN 471-
17x1 8 0335761014
15 deep groove ball
bearing 6003 ZZ 8 0335761015
16 countershaft ¢ 17 mm 4 0335761016
17 support roller ¢ 60 mm 4 0335761017
18
19
No Designation Size pcs Item No
OPTIMUM
MASCHINEN - GERMANY
© 2006
GB
5
2 / 01 / 2006 Version 1.0 MSR 4 Material stand
OPTIMUM
MASCHINEN - GERMANY
© 2006 GB
6Material stand MSR 4 Version 1.0 2 / 01 / 2006
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
HP D3H25UT Datasheet
-
Elo Touch Solutions X2-15 User manual
-
protech PA-6722 User manual
-
-
MAHA MSR 400 Operating instructions
-
Classe Audio RBG:11000076 User manual
-
AURES W-TOUCH User manual
-
Wincor Nixdorf BEETLE /ExpressBEETLE /Express 15 Installation guide
-
AURES NINO II User manual
-
