Aruba JL853AAE Configuration Guide

IMC Orchestrator 6.2 Solution

Service Configuration Guide in Non-Cloud

Scenarios

The information in this document is subject to change without notice.

i 
Contents 
Overview ························································································1 
Configure basic controller settings ·······················································2 
Log in to the controller··················································································································· 2 
Add a fabric ································································································································ 2 
Configure a VDS ·························································································································· 3 
Configure global parameters ·········································································································· 4 
Add a border device group ············································································································· 5 
Configure VLAN-VXLAN mapping ··································································································· 6 
Add a tenant ······························································································································· 8 
Add a border gateway ··················································································································· 8 
Bind the border gateway to the tenant ···························································································· 10 
Configure a single security egress ····················································· 12 
Network planning ······················································································································· 12 
Network topology ················································································································ 12 
Resource plan ···················································································································· 16 
Deploymeng workflow ················································································································· 17 
Procedure ································································································································· 17 
Configure basic settings of the underlay network ······································································· 17 
Configure basic settings of security service resources ································································ 18 
Configure basic controller settings ·························································································· 18 
Configure the tenant overlay network ······················································································ 20 
Bind the FW service resources to a tenant ··············································································· 23 
Add a firewall ······················································································································ 24 
Bind the LB service resources to the tenant ·············································································· 28 
Create an LB ······················································································································ 29 
Create an external network ··································································································· 38 
Bind a border gateway to a vRouter ························································································ 41 
Bind the vFW service resources to a vRouter············································································ 42 
Bind the vLB service resources to a vRouter ············································································ 42 
Bind an external network to the vRouter ·················································································· 43 
Check the issued configurations ····························································································· 44 
Configure the permitted VLAN and route on the border device ····················································· 47 
Verify the configuration ········································································································· 48 
Configure direct egresses ································································ 49 
Configure a direct egress in static route mode ················································································· 49 
Network planning ················································································································ 49 
Deployment workflow ··········································································································· 52 
Procedure ·························································································································· 52 
Verify the configuration ········································································································· 59 
Configure a BGP direct egress ····································································································· 60 
Network planning ················································································································ 60 
Deployment workflow ··········································································································· 64 
Procedure ·························································································································· 64 
Verify the configuration ········································································································· 74 
Configure an OSPF direct egress (DR interface) to the external network ·············································· 83 
Network planning ················································································································ 83 
Deployment workflow ··········································································································· 87 
Procedure ·························································································································· 87 
Verify the configuration ······································································································· 111 
Configure an OSPF direct egress (non-DR interface) to the external network ······································ 112 
Network planning ·············································································································· 112 
Deployment workflow ········································································································· 115 
Procedure ························································································································ 115 
Configure an OSPF direct egress to the internal network ································································· 129 

ii 
Network planning ·············································································································· 129 
Deployment workflow ········································································································· 133 
Procedure ························································································································ 133 
Verify the configuration ······································································································· 158 
Configure a BGP direct egress to a directly connected external network ············································· 158 
Network planning ·············································································································· 158 
Deployment workflow ········································································································· 161 
Procedure ························································································································ 161 
Configure a direct egress (static route) to a directly connected external network ·································· 175 
Network planning ·············································································································· 175 
Deployment workflow ········································································································· 179 
Procedure ························································································································ 179 
Verify the configuration ······································································································· 196 
Configure the service chain ···························································· 198 
Configure an east-west FW service chain ····················································································· 198 
Network planning ·············································································································· 198 
Deployment workflow ········································································································· 201 
Procedure ························································································································ 201 
Verify the configuration ······································································································· 209 
Configure an east-west LB service chain ······················································································ 211 
Network planning ·············································································································· 211 
Deployment workflow ········································································································· 214 
Procedure ························································································································ 214 
Verify the configuration ······································································································· 226 
Configure a south-north FW service chain and a direct egress ·························································· 227 
Network planning ·············································································································· 228 
Deployment workflow ········································································································· 231 
Procedure ························································································································ 231 
Verify the configuration ······································································································· 240 
Configure a south-north LB service chain and a direct egress ··························································· 242 
Network planning ·············································································································· 242 
Deployment workflow ········································································································· 244 
Procedure ························································································································ 244 
Verify the configuration ······································································································· 259 
Configure a third-party FW service chain ······················································································ 260 
Network planning ·············································································································· 260 
Deployment workflow ········································································································· 262 
Procedure ························································································································ 262 
Verify the configuration ······································································································· 266 
Configure a third-party LB service chain ······················································································· 268 
Network planning ·············································································································· 268 
Deployment workflow ········································································································· 269 
Procedure ························································································································ 269 
Verify the configuration ······································································································· 275 
Configure direct access of the LB to the external network ····················· 277 
Network planning ····················································································································· 277 
Network topology ·············································································································· 277 
Resource plan ·················································································································· 279 
Deployment workflow ················································································································ 279 
Procedure ······························································································································· 279 
Configure basic settings of the underlay network ····································································· 279 
Configure basic settings of security service resources ······························································ 280 
Configure basic controller settings ························································································ 280 
Configure the tenant overlay network ···················································································· 282 
Bind the VLB service resources to the tenant ·········································································· 285 
Add an LB ························································································································ 286 
Add an external network ····································································································· 297 
Bind a gateway to the vRouter ····························································································· 299 
Bind the vLB service resources to a vRouter ·········································································· 300 
Bind an external network to the vRouter ················································································ 301 

iii 
Check the issued configurations ··························································································· 302 
Configure the permitted VLAN on the border device ································································· 304 
Verify the configuration ············································································································· 304 
Configure the EPG denylist and allowlist ··········································· 304 
Network planning ····················································································································· 305 
Network topology ·············································································································· 305 
Resource plan ·················································································································· 307 
Deployment flow ······················································································································ 308 
EPG allowlist deployment flow ····························································································· 308 
EPG denylist deployment flow ····························································································· 309 
Procedure ······························································································································· 309 
Configure the basic environment of the controller ···································································· 309 
Add an EPG allowlist ········································································································· 321 
Add an EPG denylist ·········································································································· 333 
Configure an east-west EPG FW service chain ··································· 347 
Network planning ····················································································································· 347 
Network topology ·············································································································· 347 
Resource plan ·················································································································· 350 
Deployment workflow ················································································································ 350 
Procedure ······························································································································· 351 
Configure basic controller settings ························································································ 351 
Configure the tenant overlay network ···················································································· 352 
Configure an FW ··············································································································· 354 
Configure an EPG ············································································································· 360 
Configure a service path ····································································································· 361 
Configure an application policy ···························································································· 362 
Verify the configuration ············································································································· 364 
Verify configurations deployed by the controller ······································································· 364 
Verify the connectivity ········································································································ 367 
Configure an east-west EPG LB service chain ········································1 
Network planning ························································································································· 1 
Network topology ·················································································································· 1 
Resource plan ······················································································································ 3 
Deployment workflow ···················································································································· 3 
Procedure ··································································································································· 4 
Configure basic settings of the underlay network ········································································· 4 
Configure basic controller settings ···························································································· 4 
Configure the tenant overlay network ························································································ 5 
Configure load balancing ········································································································ 7 
Configure an EPG ··············································································································· 22 
Configure a service path ······································································································· 24 
Configure an application policy ······························································································ 25 
Verify the configuration ··············································································································· 27 
Verify configurations deployed by the controller ········································································· 27 
Verify the connectivity ·········································································································· 30 
Configure a south-north EPG FW service chain ···································· 31 
Network planning ······················································································································· 31 
Network topology ················································································································ 31 
Resource plan ···················································································································· 33 
Deployment workflow ·················································································································· 34 
Procedure ································································································································· 34 
Configure basic settings of the underlay network ······································································· 34 
Configure basic settings of security service resources ································································ 35 
Configure basic controller settings ·························································································· 35 
Configure the tenant overlay network ······················································································ 36 
Add a south-north EPG service chain ······················································································ 41 
Verify the configuration ········································································································· 50 

iv 
Configure a south-north EPG LB service chain ····································· 55 
Network planning ······················································································································· 55 
Network topology ················································································································ 55 
Resource plan ···················································································································· 56 
Deployment workflow ·················································································································· 58 
Procedure ································································································································· 58 
Configure basic settings of the underlay network ······································································· 58 
Configure basic settings of security service resources ································································ 59 
Configure basic controller settings ·························································································· 59 
Configure the tenant overlay network ······················································································ 60 
Add a south-north EPG service chain ······················································································ 65 
Verify the configuration ········································································································· 81 
Configure the EPG service chain for third-party devices ························· 87 
Network planning ······················································································································· 87 
Network topology ················································································································ 87 
Resource plan ···················································································································· 88 
Deployment workflow ·················································································································· 89 
Procedure ································································································································· 89 
Configure the basic environment ···························································································· 89 
Configure an IPv4 EPG service chain ······················································································ 92 
Configure an IPv6 EPG service chain ······················································································ 98 
Configure the controller connected to non-cloud VMware platforms ········ 105 
Network planning ····················································································································· 105 
Network topology ·············································································································· 105 
Resource plan ·················································································································· 106 
Deployment workflow ················································································································ 107 
Procedure ······························································································································· 107 
Configure basic settings of the underlay network ····································································· 107 
Configure basic controller settings ························································································ 107 
Configure the tenant overlay network ···················································································· 108 
Manage the vCenter and configure basic settings of vCenter ····················································· 110 
Add a VDS ······················································································································· 112 
Add hosts to the vCenter ···································································································· 114 
Add a distributed port group and bring a VM online based on the VLAN-VXLAN mapping ··············· 118 
Add a distributed port group and bring a VM online based on automatic VLAN allocation and bound 
interface availability zone ···································································································· 130 
Add a distributed port group and bring a VM online based on manual VLAN allocation and bound 
interface availability zone ···································································································· 133 
Add a distributed port group and bring a VM online based on manual VLAN trunk allocation and bound 
interface availability zone ···································································································· 135 
Add a distributed port group and bring VMs online in a hierarchical manner·································· 137 
Add a distributed port group and bring VMs online in a hierarchical manner (PVLAN) ····················· 139 
Verify the configuration ······································································································· 143 
Migrate a VM ···················································································································· 144 
Audit and synchronization ··································································································· 144 
Pull inventory ···················································································································· 146 
Configure the controller connected to RHVM ······································ 150 
Network planning ····················································································································· 150 
Network topology ·············································································································· 150 
Resource plan ·················································································································· 153 
Deployment workflow ················································································································ 153 
Procedure ······························································································································· 153 
Configure basic settings of the underlay network ····································································· 153 
Configure basic controller settings ························································································ 153 
Configure the tenant overlay network ···················································································· 154 
Connect to the RHVM ········································································································ 158 
Add a logical network ········································································································· 159 
Bring VMs online and ping between VMs ··············································································· 161 

v 
Pull inventory ···················································································································· 166 
Audit and synchronization ··································································································· 167 
Configure the controller connected to Microsoft System Center ·············· 171 
Network planning ····················································································································· 171 
Network topology ·············································································································· 171 
Resource plan ·················································································································· 172 
Deployment workflow ················································································································ 173 
Procedure ······························································································································· 173 
Configure basic settings of the underlay network ····································································· 173 
Configure basic controller settings ························································································ 173 
Configure the tenant overlay network ···················································································· 174 
Connect to the System Center ····························································································· 178 
Add a logical switch ··········································································································· 181 
Add a VM network ············································································································· 184 
Onboard VMs and verify connectivity between VMs ································································· 188 
Audit and synchronization ··································································································· 196 
Configure cloud private lines ··························································· 200 
Network planning ····················································································································· 200 
Network topology ·············································································································· 200 
Resource plan ·················································································································· 202 
Deployment workflow ················································································································ 203 
Procedure ······························································································································· 203 
Configure basic settings of the underlay network ····································································· 203 
Configure basic settings of security service resources ······························································ 203 
Configure basic controller settings ························································································ 204 
Configure the tenant overlay network ···················································································· 205 
Verify the configuration ············································································································· 213 
Verify configurations deployed by the controller ······································································· 213 
Verify the connectivity ········································································································ 214 
Configure EVPN multicast ······························································ 215 
Network planning ····················································································································· 215 
Network topology ·············································································································· 215 
Resource plan ·················································································································· 217 
Deployment workflow ················································································································ 218 
Procedure ······························································································································· 220 
Configure basic settings of the underlay network ····································································· 220 
Configure basic controller settings ························································································ 220 
Intra-VPN Layer 2 multicast in a DC ······················································································ 222 
VPN+PIM-SM multicast in a DC ··························································································· 227 
VPN+PIM-SSM multicast in a DC ························································································· 236 
Cross-VPN in a DC ············································································································ 245 
External network multicast ·································································································· 255 
Configure a vRouter link ································································ 266 
Distributed vRouter link ············································································································· 266 
Network planning ·············································································································· 266 
Deployment workflow ········································································································· 269 
Procedure ························································································································ 269 
Verify the configuration ······································································································· 273 
Centralized vRouter link ············································································································ 276 
Network planning ·············································································································· 276 
Deployment workflow ········································································································· 281 
Procedure ························································································································ 281 
Verify the configuration ······································································································· 290 
Configure the remote leaf ······························································· 292 
Network planning ····················································································································· 292 
Network topology ·············································································································· 292 
Resource plan ·················································································································· 294 

vi 
Deployment workflow ················································································································ 295 
Procedure ······························································································································· 295 
Configure the network for communication between the central DC and remote DC ························ 295 
Implement automatic deployment of the remote underlay network ·············································· 298 
Deploy the remote leaf overlay service ·················································································· 307 
Deploy security incorporation for the remote leaf ····································································· 311 
Verify the configuration ······································································································· 311 
Configure single-VPC NAT traversal for VPC interconnection ················ 312 
Configure single-VPC NAT traversal for VPC interconnection (single border group) ······························ 312 
Network planning ·············································································································· 312 
Deployment workflow ········································································································· 317 
Procedure ························································································································ 317 
Configure single-VPC NAT traversal for VPC interconnection (multi-border groups) ······························ 333 
Network planning ·············································································································· 333 
Deployment workflow ········································································································· 337 
Procedure ························································································································ 337 
Monitoring ······················································································0 
FAQ ······························································································0 
 

1

Overview

In non-cloud scenarios, cloud platforms such as OpenStack are unavailable, and a controller acts

as the network, computing, and security configuration entry to implement network management and

service orchestration.

In the IMC Orchestrator solution, a controller supports multi-fabric management. A fabric network

adopts the Spine-Leaf or Spine-Aggregation-Leaf structure.

Figure 1 shows the typical networking in a non-cloud scenario. When a spine device is connected to

leaf devices, the spine device forwards data on the underlay network between the leaf devices.

Server leaf devices are connected to computing devices such as servers, VMware VMs, RedHat

VMs, and Kubernetes containers. Service leaf devices are connected to HPE firewalls (FWs), HPE

load balancers (LBs), and third-party devices.

Figure 1 Typical networking in a non-cloud scenario

Fabric ED devices implement Layer 2/Layer 3 interconnection between fabrics. DCI ED devices

implement Layer 2/Layer 3 interconnection between data centers (DCs).

Border devices are connected to external devices to realize communication between the internal and

external networks. FWs, LBs, and third-party devices are connected to the border devices in hairpin

mode to enable internal network devices to access the external network through the security devices.

The leaf devices, ED devices, and border devices adopt the DRNI mode for networking. Spine

devices use more nodes for networking, and spine border devices adopt DRNI for networking.

Border1 Border2

Server

Leaf1 Server

Leaf2

Server1 Server2

IPL

Spine1 Spine2

Service

Leaf1 Service

Leaf2

FW3 FW4

IPL

FW1 FW2

Internet

Border1 Border2

Server

Leaf1 Server

Leaf2

Server1 Server2

IPL

Spine1 Spine2

Service

Leaf1 Service

Leaf2

FW3 FW4

IPL

LB1 LB2 FW1 FW2

Internet

Fabric1 Fabric2

Fabric

ED1 Fabric

ED2

DCI ED

Other DC

2

Configure basic controller settings

This chapter describes only the general operation steps for configuring basic controller settings. For

the specific configuration content and data, see "Configure basic controller settings" in each scenario.

Log in to the controller

After the controller is deployed, the corresponding menu items are loaded in IMC PLAT, and you can

use the controller functions by logging in to IMC PLAT.

IMC PLAT provides a user-friendly GUI. The login method is as follows:

1. Enter http://ip_address:30000/central/index.html in the address bar of the browser, and

press Enter to open the login page as shown in Figure 2.

 Ip_address is the virtual IP address of the cluster northbound service of the Installer where

IMC PLAT is located.

 30000 is the port number.

Figure 2 IMC PLAT login page

Add a fabric

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

1. Navigate to Automation > Data Center Networks > Fabrics > Fabrics. Click Add. On the

page for adding a fabric, configure the fabric parameters:

 Name: fabric1

 AS number: 100. It is mandatory, and must be the same as the BGP AS number of each

device in the fabric.

 Multicast network: Off (default). If multicast is used, set this parameter to On.

 Epg controller: Off (default). If End Point Group (EPG) is used, set this parameter to On.

 Configure other parameters based on the networking requirements. The default

configuration is used as an example here.

3

Figure 3 Adding a fabric

2. Click OK to create the fabric.

3. Click the icon in the Actions column, and then click the Settings tab to open the fabric

settings page. On this page, complete the advanced configuration of the fabric based on the

actual networking requirements. To reduce packet flood on the network, you are advised to

select Unknown Unicast Suppression, Unknown Multicast Suppression, and Broadcast

Suppression. For other parameters, the default configuration is used as an example here.

Figure 4 Advanced settings of the fabric

Configure a VDS

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

1. Navigate to Automation > Data Center Networks > Common Network Settings > Virtual

Distributed Switches. Click the Modify icon in the Actions column, and modify VDS 1 by

adding the created fabric fabric1 on the Carrier Fabric tab.

4

Figure 5 Adding a fabric for the VDS

2. Click the Advanced Settings tab, and configure the following parameters of VDS 1:

 Bridge name: vds1-br

 VXLAN tunnel interface name: vxlan_vds1-br

 vSwitch Learned Flow Entries Aging Time (seconds): 300

 Configure other parameters based on the networking requirements. The default

configuration is used as an example here.

Figure 6 Advanced settings

3. Click Apply to save the settings.

Configure global parameters

1. To ensure the normal use of IPv6 services (if any), enable the global IPv6 configuration on the

controller as follows:

a. Navigate to Automation > Data Center Networks > Fabrics > Parameters, and click the

Controller Global Settings tab.

b. Set IPv6 to On.

2. Disable Deploy Security Policy Flow Table to Switching Devices as follows:

a. Navigate to Automation > Data Center Networks > Fabrics > Parameters, and click the

Controller Global Settings tab.

b. Set Deploy Security Policy Flow Table to Switching Devices to Off.

3. If it is required to generate the VRF names according to rules, select the VRF autonaming mode

in the controller as follows:

5

a. Navigate to Automation > Data Center Networks > Fabrics > Parameters, and click the

Controller Global Settings tab.

b. Set VRF Autonaming Mode to Rule-based. The generated VRF name is in the following

format: Tenant name_Router name_Segment ID.

Figure 7 Controller global settings

Add a border device group

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

1. Navigate to Automation > Data Center Networks > Fabrics > Fabrics, click the icon in

the Actions column for fabric1, and click the Border Device Group tab.

2. Click Add to go to the page for adding a border device group, and configure the following

parameters in the Basic Info area:

 Device Group Name: Custom name of the device group.

 Remote Device Group: Specify whether the device group is remote. Once configured, this

parameter cannot be modified. Therefore, you must plan this parameter.

 Position: Network position of the border device group. You can select multiple positions.

Once configured, this parameter cannot be modified. Therefore, you must plan this

parameter.

 HA Mode: Specify the deployment mode.

3. In the Border Gateway Settings area, configure the following parameters:

 Third-Party Firewall: Off. Configure this parameter based on the networking requirements.

 Firewall Deployment Mode: Inline. Configure this parameter based on the networking

requirements.

 Connection Mode: Specify the mode of connection between the border device and service

device. Once configured, this parameter cannot be modified. Therefore, you must plan this

parameter.

 IPAddress Pool List: Configure this parameter based on the networking requirements.

 VLAN Pool List: Configure this parameter based on the networking requirements.

6

Figure 8 Adding a border device group

4. Add the border device in the Device Group Members area.

5. Click Apply in the upper right corner to add the border device group.

6. If you use the automatic deployment mode to configure the underlay network, the controller

automatically performs DRNI deployment on the two member devices of the added border

device group. To manually add the DR interface configuration on the controller, see IMC

Orchestrator 6.2 Solution Underlay Network Configuration Guide.

Configure VLAN-VXLAN mapping

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

Before performing the configuration described in this chapter, you must execute the vtep access

port command on the access port of the connected device. If you do not do that, you cannot bind

the VLAN-VXLAN mapping to this port on the controller. The configuration method is as follows:

[server-leaf1] interface Bridge-Aggregation257

[server-leaf1-Bridge-Aggregation257] vtep access port

[server-leaf1-Bridge-Aggregation257] quit

1. Navigate to Automation > Data Center Networks > Resource Pools > VNID Pools > VLAN-

VXLAN Mappings. Click Add, select VLAN-VXLAN Mapping to go to the Add VLAN-VXLAN

Mapping page, and perform the following operations:

a. Enter the mapping name map1.

Figure 9 VLAN-VXLAN mapping settings

7

a. Click Add Mapping, and configure the following parameters in the dialog box that opens:

− Name: map001

− Start VLAN ID: 2001

− Start VXLAN ID: 2001

− Mapping Range Length: 4

− Access Mode: VLAN

Figure 10 Adding a VLAN-VXLAN mapping

a. Click Apply.

2. On the Apply to Device or Apply to Interface tab, apply the mapping to a device or an

interface. For example, to apply the mapping to an interface:

a. Select map1 on the VLAN-VXLAN mapping page.

b. Click Interface in the Apply to Interfaces area to go to the Apply to Interfaces page.

3. Select a device from the device list. Select an access interface (or an aggregate interface) of

the device, and add the selected interface to the selected interface list on the right. Click Apply.

Figure 11 Selecting an interface

8

4. View the created mapping in the list.

Figure 12 Mapping information

Add a tenant

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

1. Navigate to Automation > Data Center Networks > Tenant Management > All Tenants.

Click Add, and configure the following parameters on the Add Tenant page:

 Tenant Name: Custom tenant name, for example, tenant1

 VDS Name: VDS1

Figure 13 Adding a tenant

2. Click Apply.

Add a border gateway

This chapter describes only the configuration example. For the specific configuration content and

data, see "Configure basic controller settings" in each scenario.

1. Navigate to Automation > Data Center Networks > Common Network Settings > Border

Gateway. Click Add, and configure the following parameters on the Add Border Gateway

page:

 Name: Custom border gateway name, for example, gw1.

 Gateway Sharing: Off. Configure this parameter based on the networking requirements.

9

 Gateway Type: Composite gateway. Configure this parameter based on the networking

requirements.

 Configure other parameters based on the networking requirements. The default

configuration is used as an example here.

Figure 14 Adding a border gateway

2. Click Add Border Gateway Members, and configure the following parameters on the Add

Border Gateway Members page:

 Name: Custom name of the border gateway member, for example, gw1member.

 Fabric: fabric1.

 Device Group: bdgroup1. Select the border device group created for the fabric.

 Priority: 1. Set this parameter to a value between 0 and 99 based on the networking

requirements. A larger number indicates a higher priority.

3. Add service resources (if required) on the Add Border Gateway Member or Modify Border

Gateway Member page. When adding service resources, configure the following parameters:

 Service Type: Select vFW or VLB based on the networking requirements.

 Resource Source: Select VNF or L4-L7 Physical Resource Pool based on the networking

requirements.

 Resource Pool Name: Select an existing resource pool based on the networking

requirements.

10

Figure 15 Adding a border gateway member

4. Click Apply to add a border gateway member. Click Apply on the Add Border Gateway page

to add a border gateway.

Bind the border gateway to the tenant

1. Navigate to Automation > Data Center Networks > Tenant Management > All Tenants,

select tenant1, and click to open the Edit Tenant page.

Figure 16 Adding a service resource

2. Click Add in the Allocate Gateway Resources area. In the dialog box that opens, select the

border gateway, and click Apply to add the border gateway.

11

Figure 17 Binding the border gateway to the tenant

3. Click Apply.

12

Configure a single security egress

Network planning

Network topology

Figure 18 Network diagram

Table 1 lists the management IP addresses and VTEP IP addresses of switches.

Table 1 IP addresses and interfaces

Device

Function

Management IP

address

Service IP address and interface

Border1

EVPN border device

192.168.11.8

Loopback0: 10.1.1.8/32

HGE4/0/1 (connecting to HGE4/0/1 on

Border2)

HGE4/0/2 (connecting to HGE4/0/2 on

Border2)

XGE6/0/48 (connecting to XGE6/0/48 on

Border2)

HGE4/0/3 (connecting to HGE1/0/3 on

Spine1)

Internet

Border1 Border2

Leaf1 Leaf2

Server1 Server2

FW1 FW2 LB1 LB2

IPL

Spine1 Spine2

Leaf3 Leaf4

Server3 Server4

IPL

Related component

IMC Orchestrator

13

Device

Function

Management IP

address

Service IP address and interface

HGE4/0/4 (connecting to HGE1/0/3 on

Spine2)

XGE6/0/1 (connected to XGE1/2/0 on FW1)

XGE6/0/2 (connected to XGE1/2/0 on FW2)

XGE6/0/3 (connected to XGE1/2/0 on LB1)

XGE6/0/4 (connected to XGE1/2/0 on LB2)

Border2

EVPN border device

192.168.11.9

Loopback0 10.1.1.9/32

HGE4/0/1 (connecting to HGE4/0/1 on

Border1)

HGE4/0/2 (connecting to HGE4/0/2 on

Border1)

XGE6/0/48 (connected to XGE6/0/48 on

Border1)

HGE4/0/3 (connecting to HGE1/0/4 on

Spine1)

HGE4/0/4 (connecting to HGE1/0/4 on

Spine2)

XGE6/0/1 (connected to XGE1/2/1 on FW1)

XGE6/0/2 (connected to XGE1/2/1 on FW2)

XGE6/0/3 (connected to XGE1/2/1 on LB1)

XGE6/0/4 (connected to XGE1/2/1 on LB2)

Spine1

Underlay physical

device

192.168.11.2

Loopback0 10.1.1.2/32

HGE1/0/3 (connecting to HGE4/0/3 on

Border1)

HGE1/0/4 (connecting to HGE4/0/3 on

Border2)

HGE1/0/5 (connecting to HGE1/0/25 on

Leaf1)

HGE1/0/6 (connecting to HGE1/0/25 on

Leaf2)

HGE1/0/7 (connecting to HGE1/0/25 on

Leaf3)

HGE1/0/8 (connecting to HGE1/0/25 on

Leaf4)

Spine2

Underlay physical

device

192.168.11.3

Loopback0 10.1.1.3/32

HGE1/0/3 (connecting to HGE4/0/4 on

Border1)

HGE1/0/4 (connecting to HGE4/0/4 on

Border2)

HGE1/0/5 (connecting to HGE1/0/27 on

Leaf1)

HGE1/0/6 (connecting to HGE1/0/27 on

Leaf2)

HGE1/0/7 (connecting to HGE1/0/27 on

Leaf3)

HGE1/0/8 (connecting to HGE1/0/27 on

Leaf4)

Leaf1

EVPN access device

192.168.11.4

Loopback0 10.1.1.4/32

XGE1/0/9 (connecting to XGE1/0/9 on Leaf2)

Page is loading ...

Aruba JL853AAE Configuration Guide

This manual is also suitable for

Aruba JL853AAE Configuration Guide

Related papers

Other documents