Page is loading ...
© Office Star Products May 2021
GEM25
GEMELLI 2 IN 1 MONITOR MOUNT
ASSEMBLY INSTRUCTIONS
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
• 3 years on gaming desks, chairs and mounts.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
INSPECT ON ARRIVAL This product has been inspected and packaged with durable internal packing and external corrugated. Responsibility for safe delivery
was assumed by the carrier at time of shipment. CLAIMS FOR LOSS OR DAMAGE TO THE CONTENTS SHOULD THEREFORE BE MADE UPON THE
CARRIER AS BELOW.
WARNING
1. Do not use this product unless all bolts screws and knobs are
securely tightened.
2. Check that all bolts screws and knobs are tight every three
months or as needed.
3. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
4. Use this product for its intended purpose only.
5. Use mild detergent only for cleaning.
PART QTY
A. Mounting Bracket ....................2
B. Arm Frame .........................1
C. C-Clamp ...........................1
D. Support Post ....................... 1
E. Plastic Plug .........................1
F. Cord Managment Clip .................1
G. Mounting Plate (optional) ..............1
H. Thumb Screw .......................2
I. Phillips Screw ........................2
J . Rubber Sticker ......................5
K . Allen Bolt ..........................3
L . Grommet Plate (optional) ..............1
M . Allen Wrench (4mm) .................1
N . Allen Wrench (5mm) .................1
O . Allen Wrench (6mm) .................1
MOUNTING HARDWARE QTY
M-A. Bolt (M4 x 12) .....................8
M-B. Bolt (M4 x 16) .....................8
M-C. Bolt (M5 x 12) .....................8
M-D. Bolt (M5 x 16) .................... 8
M-E. Washer (D5) ......................8
M-F. Spacer ...........................8
Remove all the parts from carton, separate them into part numbers indicated on the list and make sure part quantities are correct.
STEP 1 Insert Plastic Plug (E) into Support Post (D).
STEP 2A Attach Rubber Stickers (J) to underside of C-Clamp (C). Secure C-Clamp (C) to Support Post (D) using Allen Bolts (K).
FULLY TIGHTEN ALLEN BOLTS (K) USING ALLEN WRENCH (M).
STEP 2B Remove adjustment knob from C-Clamp (C) using Phillips Screwdriver (not provided). Attach Rubber Stickers (J) to underside of Mounting
Plate (G). Attach Support Post (D) to Mounting Plate (G) and align with grommet hole of mounting surface. Slide adjustment knob through Grommet Plate (L),
mounting surface, Mounting Plate (G) and into Support Post (D). SECURELY TIGHTEN ADJUSTMENT KNOB.
STEP 3A Slide Cord Management Clip (F) onto Support Post (D). Attach Arm Frame (B) to top end of Support Post (D) and secure using
Allen Wrenches (N & O). FULLY TIGHTEN PRE-INSTALLED BOLTS.
STEP 3B To remove arm on Arm Frame (B), unscrew and remove pre-installed bolt using Allen Wrench (N).
Slide Cord Management Clip (F) onto Support Post (D). Attach Arm Frame (B) to top end of Support Post (D) and secure using Allen Wrenches (N & O).
FULLY TIGHTEN PRE-INSTALLED BOLTS.
STEP 1
STEP 2A
C-CLAMP OPTION
STEP 3A
DUAL MONITOR OPTION
STEP 3B
SINGLE MONITOR OPTION
STEP 2B
GROMMET OPTION
Phillips screwdriver also needed for assembly
(not provided)
mounting surface
GEM25
GEMELLI 2 IN 1 MONITOR MOUNT
ASSEMBLY INSTRUCTIONS
GEM25
GEMELLI 2 IN 1 MONITOR MOUNTUNT
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 4 Secure Mounting Bracket (A) to rear of TV/monitor. Choose correct hardware configuration based on depth of TV/monitor mounting holes.
FULLY TIGHTEN BOLTS USING PHILLIPS SCREWDRIVER (not provided).
STEP 5 Carefully slide Mounting Bracket (A) onto Arm Frame (B). Secure Mounting Bracket (A) using one Phillips Screw (I) and one Thumb Screw (H) for
each Mounting Bracket (A).FULLY TIGHTEN PHILLIPS SCREWS (I) USING PHILLIPS SCREWDRIVER (not provided).
Further secure Mounting Brackets (A) by fully tightening pre-installed bolts on ends of Arm Frame (B) using Allen Wrench (O).
ATTENTION: MAKE SURE ALL SCREWS & BOLTS ARE FULLY TIGHTENED BEFORE USING PRODUCT.
STEP 5
Run TV/Monitor cables through cable management clips. Be sure Arm Frame (B) remains in a straight (fixed)
position from point of contact with Support Post (D).
Cord Management Clip (F) provides Allen Wrench caddy. Mounting Brackets (A) can be adjusted up and down
as well as a + or - 45� pivot.
GEM25
GEMELLI 2 IN 1 MONITOR MOUNT
ASSEMBLY INSTRUCTIONS
GEM25
GEMELLI 2 IN 1 MONITOR MOUNT
ASSEMBLY INSTRUCTIONS
/
