Aoni E93G Smart Battery Doorbell Camera User guide
- Type
- User guide
Quick Start Guide
Smart Battery Doorbell Camera
Model: E93G
Welcome
Thank you for choosing our smart camera.
Getting started is easy.
What’s Included
Video Doorbell Back Veneer Power Adapter
USB Cable
Product Details 1. Connection Preparation
Bring the doorbell and phone within 1 to 3 feet (30 to 100
centimeters) of the router.
Router
30cm~100cm
Doorbell Smartphone
Note: Make sure smart phone is connected with your
wireless router.
Please note the doorbell is only working under 2.4G Wi-Fi,
not support 5G Wi-Fi.
For the best experience, please download the "Tuya smart"
APP to your smartphone from App Store or Google Play, or
you can also scan the QR code below, the APP icon will be
displayed after installed successfully.
2. Get the APP and Account
Launch the app from your smartphone and click the Sign Up
button. Follow the on-screen instructions.
7. Schematic diagram of doorbell
installation
6.Pairing of doorbell and chime
Connect the power to the doorbell by Micro USB Power
Adapter.(DC5V/1.5A)
4. Connect the power to the doorbell
Hammer expansion bolt into wall body as per the hole
position of locating sticke;
Use a screw to fix the back plate;
Put the doorbell downward to buckle it on the back plate
to complete installation.
You’re done!
Congratulations! Your doorbell is set up and ready to go.
All trademarks are used for reference
purposes only.
Thanks again for choosing our smart camera! Makelife
safe in your hands!
Boost security mobility in your smartphone!
Appendix: Camera LED Guide
NO. LED Status Camera Status
1 System starting upWhite LED on for 2 seconds
2 Standby for configurationWhite LED blinks slowly
3 Doorbell networking failureWhite LED blinks quickly
4Doorbell networking successfulWhite LED on for 2 seconds
5
6
7
8
9
10
11
12
Doorbell sleeping normallyWhite LED goes out
Doorbell wake upWhite LED breath flash
Press the doorbell buttonWhite LED breath flash
OTA upgradeWhite LED blinks slowly
Doorbell chargingGreen LED on
Doorbell charging completeGreen LED goes out
Doorbell charging abnormallyGreen LED blinks quickly
Doorbell working abnormallyWhite LED always on
USB Chime or DC Chime 3M tape Spanner
Power interface
Lens
Ambient Light
Detection
Speaker
PIR
Doorbell Buttons
Volume Button
Ringtone Button
Doorbell Bottom View Chime
Doorbell Front View Doorbell Rear View
Micro SD card
Power Switch
Reset
Insert the Micro SD card gently on the side edge of doorbell.
3. Insert the Micro SD card
Press the Reset button for above 5 seconds, then release
the button to reset the camera, then the LED light will blink
in white slowly.
Click "Add Device" or "+" on the right corner to add device;
Then click" Security&Video Surveillance" to select
" Smart Doorbell"
5. Set up your doorbell
Follow the App's instructions and input the right wifi
password; Point the QR code to the camera lens for
15-20cm ; Click"HEARD THE BEEP" when you heard
"dingding". After processing, it paired successfully.
The white light is on, camera is ready for viewing.
Wall Mount Screw Sets
X2
Tuya Smart Tuya Smart
成品尺寸：77*120mm
折后封面
深圳奥尼电子股份有限公司
SHENZHEN AONI ELECTRONIC CO., LTD
FORMAT
版 本
日 期
DATE
比例
APPROVED
批 准
要求
±1°
角 度
±1°
变更NO. 年/月/日
尺 寸 公 差
尺 寸
±1mm
位 数
记 事
审 核
CHECKED
DRAWN
制 图
设 计
DESIGNED
x / x . x
1 : 1 2022.09.06
A
夏媛媛 韦静
128g铜版纸，
单黑色两面印刷，
RoHS
品名
料号
IPC_E93G_中性_
折页_说明书
Press the Reset
button for above
5 seconds
Quick Start Guide
Quick Start Guide
Smart Battery Doorbell Camera
Model: E93G
white LED
blinks
1
1
2
2
3
Press and keep the volume button of chime, until you
hear the sound of “Ding Ding Ding Ding” from chime.
Press the doorbell button, you can hear" Ding dong" too.
Press the doorbell button again, the chime rings mean
the paring is successful.
1
2
3
3
Back Veneer DoorbellWall
Indicator LED
展开尺寸：385*120mm
40610E93G0002
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a
class B digital device,pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequence energy and,if
not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that
interference will not occur in a particular installation.if this equipmemt does
cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on,the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minumum distance of 20
cm between the radiator and your body.
FCC Statement
-
1
