Klutch P600iHD Owner's manual

Category
Power tools
Type
Owner's manual
SAVE THESE INSTRUCTIONS
P600iHD 60 Amp Plasma Cutter
Owner’s Manual
WARNING: Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item #55726
Page 2 of 22
Thank you very much for choosing a Klutch product!
For future reference, please complete the owner’s record below:
Serial Number/Lot Date Code: ________________________________
Purchase Date: ____________________________________________
Save the receipt, warranty, and this manual. It is important that you read
the entire manual to become familiar with this product before you begin
using it.
This plasma cutter is designed for certain applications only. Northern
Tool & Equipment is not responsible for issues arising from modification
or improper use of this product such as an application for which it was
not designed. We strongly recommend that this product not be modified
and/or used for any application other than that for which it was designed.
For technical questions, please call 1-800-222-5381.
Page 3 of 22
Table of Contents
Intended Use .......................................................................................................................................... 4
Important Safety Information ............................................................................................................... 5
General Safety Rules ............................................................................................................................ 6
Specifications of P600iHD .................................................................................................................. 10
Main Parts of P600iHD ........................................................................................................................ 11
Setting Up Equipment ......................................................................................................................... 12
Operating Instructions ........................................................................................................................ 14
Maintenance ........................................................................................................................................ 15
Troubleshooting .................................................................................................................................. 16
Parts Diagram ...................................................................................................................................... 18
Parts List .............................................................................................................................................. 18
Replacement Parts .............................................................................................................................. 20
Limited Warranty ................................................................................................................................. 21
Page 4 of 22
Intended Use
The Klutch P600iHD is a heavy-duty, 60 amp, DC inverter plasma cutter. Its intended use is for
cutting through steel, stainless steel, aluminum, and other metals. This unit is designed to cut up
to 7/8" steel (sever cut) at a travel speed of 10 inches per minute, when operating on 230V AC
power. Plasma cutting does require a source of compressed air and this unit in particular requires
a compressed air source that can provide 60 PSI at a rate of 4.5 CFM. Compressed air supply
should not exceed 100 PSI.
Plasma cutting is an alternative to oxygen/acetylene cutting. Since plasma cutting does not
require flammable and combustible gases, it is considered a safer alternative to oxygen/acetylene
cutting. The plasma arc is designed to cut through metal and does so efficiently, providing a clean
cut edge.
This unit is intended to be used on a 50 amp 230V AC circuit without the use of an extension cord.
If an extension cord is necessary for your application, use the appropriate size and length of
extension cord that will handle the required input amps the entire length of the extension. We
highly recommend talking with a qualified electrician for cord size recommendations. This unit is
supplied with a NEMA Class 6-50P plug and will require a NEMA Class 6-50R receptacle. Do not
remove the power plug!
Accessories Included:
(1) 12 ft. Removable plasma torch
(1) 10 ft. Ground cable/clamp
(3) Extra electrodes
(3) Nozzles
Page 5 of 22
Important Safety Information
WARNING
Read and understand all instructions. Failure to follow all instructions may result in serious injury
or property damage.
The warnings, cautions, and instructions in this manual cannot cover all possible conditions or
situations that could occur. Exercise common sense and caution when using this tool. Always be
aware of the environment and ensure that the tool is used in a safe and responsible manner.
Do not allow persons to operate or assemble the product until they have read this manual and
have developed a thorough understanding of how it works.
Do not modify this product in any way. Unauthorized modification may impair the function and/or
safety and could affect the life of the product. There are specific applications for which the product
was designed.
Use the right tool for the job. DO NOT attempt to force small equipment to do the work of larger
industrial equipment. There are certain applications for which this equipment was designed. It will
be a safer experience and do the job better at the capacity for which it was intended. DO NOT use
this equipment for a purpose for which it was not intended.
Industrial or commercial applications must follow OSHA requirements.
WARNING
WORK AREA SAFETY
Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit.
Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas
may put you dangerously close to other cutting tools and rotating parts.
Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence
of flammable liquids, gases, or dust. The product can create sparks, which may ignite the
flammable liquids, gases, or dust.
Do not allow the product to come into contact with an electrical source. The tool is not insulated
and contact will cause electrical shock.
Keep children and bystanders away from the work area while operating the tool. Do not allow
children to handle the product.
WARNING
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use
the tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of
inattention while operating the tool may result in serious personal injury.
Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving
Page 6 of 22
parts. Air vents on the tool often cover moving parts and should be avoided.
Wear the proper personal protective equipment when necessary. Use ANSI Z87.1 compliant safety
goggles (not safety glasses) with side shields, or when needed, a face shield. Use a dust mask in
dusty work conditions. Also use non-skid safety shoes, hardhat, gloves, dust collection systems,
and hearing protection when appropriate. This applies to all persons in the work area.
Do not overreach. Keep proper footing and balance at all times.
CAUTION
PLASMA CUTTER USE AND CARE
Do not force the plasma cutter. Products are safer and do a better job when used in the manner
for which they are designed. Plan your work, and use the correct product for the job.
Check for damaged parts before each use. Carefully check that the product will operate properly
and perform its intended function. Replace damaged or worn parts immediately. Never operate the
product with a damaged part.
Store the plasma cutter when it is not in use. Store it in a dry, secure place out of the reach of
children. Inspect the tool for good working condition prior to storage and before re-use.
Use only accessories that are recommended by the manufacturer for use with your product.
Accessories that may be suitable for one product may create a risk of injury when used with
another tool. Never use an accessory that has a lower operating speed or operating pressure than
the tool itself.
Keep guards in place and in working order. Never operate the product without the guards in place.
General Safety Rules
WARNING
Read and understand all instructions. Failure to follow all instructions listed below may result in
serious injury.
CAUTION
Do not allow persons to operate or assemble this product until they have read this manual and
have developed a thorough understanding of how the unit works.
WARNING
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the
operator that common sense and caution are factors which cannot be built into this product but
must be supplied by the operator.
Page 7 of 22
WARNING
Your Welding/Cutting Environment
Keep the environment you will be welding or cutting in free from flammable materials.
Always keep a fire extinguisher accessible to your welding/cutting environment.
Always have a qualified person install and operate this equipment.
Make sure the area is clean, dry, and ventilated. Do not operate the plasma cutter in humid,
wet, or poorly ventilated areas.
Always have your plasma cutter maintained by a qualified technician in accordance with local,
state, and national codes.
Always be aware of your work environment. Be sure to keep other people, especially children,
away from you while cutting.
Keep harmful arc rays shielded from the view of others.
Mount the plasma cutter on a secure bench or cart that will keep the plasma cutter secure and
prevent it from tipping over or falling.
WARNING
Your Plasma Cutter’s Condition
Check the ground cable, power cord, and torch to be sure the insulation is not damaged.
Always replace or repair damaged components before using the plasma cutter.
Check all components to ensure they are clean and in good operating condition before use.
CAUTION
PLASMA CUTTER USE AND CARE
Do not operate the plasma cutter if the torch or ground cable is wet. Do not immerse them in
water. These components and the plasma cutter must be completely dry before attempting to use
them.
Follow the instructions in this manual.
Keep the plasma cutter in the OFF position when not in use.
Connect the ground lead as close to the area being cut as possible to ensure a good ground.
Do not allow any body part to come in contact with the material being cut, if you are in contact
with the ground or material being cut from another plasma cutter.
Do not cut if you are in an awkward position. Always have a secure stance while cutting to
prevent accidents. Wear a safety harness if working above ground.
Do not drape cables over or around your body.
Wear eye protection (see ANSI Z49.1 safety standard) while cutting to protect your eyes from
harmful UV and IR rays.
Wear proper gloves and protective clothing to prevent your skin from being exposed to hot
metals, UV, and IR rays.
Do not overuse or overheat your plasma cutter. Allow proper cooling time between duty
cycles.
Keep hands and fingers away from moving parts.
Do not point the torch at any of your body parts or anyone else’s.
Always use this plasma cutter in the rated duty cycle to prevent excessive heat and failure.
Page 8 of 22
WARNING
Electrical Shock
Plasma cutters can produce a shock that can cause injury or death. Touching electrically live parts
can cause fatal shocks and severe burns. While cutting, all metal components connected to the torch
are electrically hot. Poor ground connections are a hazard, so secure the ground lead before cutting.
Wear dry protective apparel: coat, shirt, gloves, and insulated footwear.
Insulate yourself from the work piece. Avoid contacting the work piece or ground.
Do not attempt to repair or maintain the plasma cutter while the power is ON.
Inspect all cables and cords for any exposed wire and replace immediately.
Use only recommended replacement cables and cords.
Always attach the ground clamp to the work piece or work table as close to the cutting area as
possible.
Do not touch the torch and the ground or grounded work piece at the same time.
Do not use a plasma cutter to thaw frozen pipes.
WARNING
Fumes and Gases
Do not use plasma cutter in the presence of gasoline, diesel, propane, or other flammable
liquids. Sparks created from the cutter may ignite liquids or fumes, causing an explosion and
serious injury or death.
Fumes emitted from the plasma cutting process displace clean air and can result in injury or
death.
Do not breathe in fumes emitted by the plasma cutting process. Make sure your breathing air
is clean and safe.
Work only in a well-ventilated area or use a ventilation device to remove plasma cutting fumes
from the environment where you will be working.
Do not plasma cut on coated materials (galvanized, cadmium plated or containing zinc,
mercury or barium). They will emit harmful fumes that are dangerous to breathe. If necessary
use a ventilator, respirator with air supply, or remove the coating from the material in the
cutting area.
The fumes emitted from some heated metals are extremely toxic. Refer to the material safety
data sheet for the manufacturer’s instructions.
Do not plasma cut near materials that will emit toxic fumes when heated. Vapors from
cleaners, sprays and degreasers can be highly toxic when heated.
WARNING
UV and IR Arc Rays
The plasma cutting arc produces ultraviolet (UV) and infrared (IR) rays that can cause injury to
your eyes and skin. Do not look at the plasma cutting arc without proper eye protection.
Always use safety glasses, a shield, or a helmet that meets ANSI Z49.1 standards for plasma
cutting.
Cover all bare skin areas exposed to the arc with protective clothing and shoes. Flame-
retardant cloth or leather shirts, coats, pants, or coveralls are available for protection.
Use screens or other barriers to protect other people from the arc rays emitted from your
plasma cutting.
Warn people in your area when you are going to strike an arc so they can protect themselves.
Page 9 of 22
WARNING
Fire Hazards
Do not plasma cut on containers or pipes that contain or have had flammable, gaseous, or
liquid combustibles in them. Plasma cutting creates sparks and heat that can ignite flammable
and explosive materials.
Do not operate any plasma cutter in areas where flammable or explosive materials are
present.
Remove all flammable materials within 35 feet of the plasma cutter. If removal is not possible,
tightly cover them with fireproof covers.
Take precautions to ensure that flying sparks do not cause fires or explosions in hidden areas,
cracks, or areas you cannot see.
Keep a fire extinguisher close in the case of fire.
Wear garments that are oil-free without pockets or cuffs that will collect sparks.
Do not have on your person any items that are combustible, such as lighters or matches.
Keep the work lead connected as close to the weld area as possible to prevent any unknown,
unintended paths of electrical current from causing electrical shock and fire hazards.
CAUTION
Hot Materials Plasma cut materials are hot and can cause severe burns if handled improperly.
Do not touch plasma cut materials with bare hands.
Do not touch the torch after cutting until it has had time to cool down.
CAUTION
Sparks/Flying Debris
Plasma cutting creates hot sparks that can cause injury. Chipping slag off cuts can create
flying debris.
Wear protective apparel at all times: ANSI-approved safety glasses or shield, a welder’s hat,
and ear plugs to keep sparks out of ears and hair.
CAUTION
Electromagnetic Field
Electromagnetic fields can interfere with various electrical and electronic devices such as
pacemakers.
Consult your doctor before using any plasma cutting device.
Keep people with pacemakers away from your plasma cutting area while cutting.
Do not wrap cable around your body while plasma cutting.
Wrap plasma torch cable and ground cable together whenever possible.
Keep plasma torch and ground cables on the same side of your body.
Page 10 of 22
WARNING
Shielding Gas Cylinders Can Explode
High pressure cylinders can explode if damaged, so treat them carefully.
Never expose cylinders to high heat, sparks, open flames, mechanical shocks, or arcs.
Do not touch the cylinder with the torch.
Do not cut on the cylinder.
Always secure cylinder upright to a cart or stationary object.
Keep cylinders away from welding, cutting, or electrical circuits.
Use the proper regulators, gas hose, and fittings for the specific application.
Do not look into the valve when opening it.
Use a protective cylinder cap whenever possible.
CAUTION
Proper Care, Maintenance, and Repair
Always have power disconnected when working on internal components.
Do not touch or handle the PC board without being properly grounded with a wrist strap. Put
the PC board in a static-proof bag to move or ship.
Do not put hands or fingers near moving parts, like the drive rolls of a fan.
WARNING
Proposition 65 Warnings
Plasma cutting equipment produces fumes or gases which contain chemicals known to the
state of California to cause birth defects and, in some cases, cancer (California Health &
Safety code section 25249.5 et seq.).
Specifications of P600iHD
Item
Power Supply
No-Load Voltage
Output Range
Duty Cycle
Compressed Air Required
Dimensions
Weight
Page 11 of 22
Main Parts of P600iHD
Figure 1.
1
2
3
4
6
12
7
9
10
8
5
11
Page 12 of 22
Reference
Subassembly
1
Air-Pressure Gauge
2
Output Amperage Control
3
Compressed Air Connection (Back Panel)
4
Air-Pressure Control Knob
5
Indicator Lights
6
Ground Cable Connection Receptacle
7
Ground Cable and Clamp
8
Torch Trigger Connection Receptacle
9
Torch
10
Torch Power Connection Receptacle
11
Torch Arc Start Connection Receptacle
12
Electrodes and Nozzles
Setting Up Equipment
WARNING
ELECTRIC SHOCK CAN KILL!
High voltage danger from power source! Consult a qualified electrician for proper installation
of receptacle. This plasma cutter must be grounded while in use to protect the operator from
electrical shock.
Do not remove grounding prong or alter the plug in any way. Use only the supplied adapter
between the plasma cutter's power cord and the power source receptacle. Make sure the
POWER switch is OFF when connecting your plasma cutter’s power cord directly to a properly
grounded 230 VAC, 60 HZ, Single Phase, 60 amp input power supply.
1. POWER REQUIREMENT 230V - AC single phase 230V (200-240V) 50/60 HZ fused with a 60
amp time delayed fuse or circuit breaker is required. DO NOT OPERATE THIS UNIT if the
ACTUAL power source voltage is less than 215 volts AC or greater than 240 volts AC.
2. EXTENSION CORD - We do not recommend extension cords because of the voltage drop
they produce. This drop in voltage can affect the performance of the plasma cutter. If you
need to use an extension cord, check with a qualified electrician and your local electrical
codes for your specific area.
3. INSTALLATION OF THE CUTTING TORCH - Your torch should be fully assembled and
ready to install. Figure 2 shows the components of the torch head and how those components
are installed.
Page 13 of 22
Figure 2.
a. Connect the Pilot Arc cable (Red) on the plasma torch to the Arc Start Cable
Connection. See Figure 3.
b. Connect the Torch Control Cable (Black) 3 prong connector to the Torch Trigger
Control Connection. See Figure 3.
c. Connect the Torch Weld Cable (Yellow Nut) to the Negative (-) output connection.
See Figure 3.
d. Connect the Grounding Cable to the Positive (+) output connection. See Figure 3.
Figure 3.
e. Connect the Ground Clamp to your workpiece.
f. Connect your compressed air source to the gas connection on this units back panel.
Positive (+)
Ground Cable Connection
Negative (-)
Torch Connection
Arc Start
Cable Connection
Torch Trigger
Control Connection
Page 14 of 22
Operating Instructions
WARNING
High voltage danger from power source!
Consult a qualified electrician for proper installation of receptacle at the power source. This
plasma cutter must be grounded while in use to protect the operator from electrical shock. If
you are not sure if your outlet is properly grounded, have it checked by a qualified electrician.
Do not cut off the grounding prong or alter the plug in any way and do not use any adapter,
other than the supplied adapter, between the plasma cutter's power cord and the power
source receptacle. Make sure the POWER switch is OFF, then connect your plasma cutter's
power cord to a properly grounded 230 VAC (220V - 240V), 60 HZ, single phase, 60 amp
power source.
PLASMA CUTTING OPERATION
1. SET-UP
a. Check the plasma cutter to see if it has been connected correctly and is in good
working condition, as described in the INSTALLATION section, and that it complies
with safe operation requirements as noted in the IMPORTANT SAFETY
CONSIDERATIONS section.
b. Switch on the power switch of the cutter to observe if the operation is normal. If it is
normal, the fan should start up and the Power Indicator Light should be on. If there is
no compressed air or the air pressure is low, the Low Pressure Indicator Light will be
on.
c. Adjust the air supply valve until the air pressure is up to the cutting torch requirement
(lowest pressure should be no less than 50PSI); the Low Pressure Indicator Light will
not be lit up in those conditions.
d. Adjust the air flow to be sure it is consistent.
e. Pull the torch trigger. The cutting operation begins after the cutting plasma pilot arc is
made.
2. CUTTING OPERATION
a. Metal Sheet Cutting
i. Place the torch’s nozzle at the start of the work piece. Turn on the torch
switch to ignite the plasma pilot. After the work piece is cut through, move the
torch along the cutting direction uniformly. The cutting speed is determined by
whether the cutting goes all the way through. If the speed is too fast, the work
piece won’t be cut through, or if too slow, the cut quality will be affected and
excessive warping may occur, or the arc could stop.
ii. When you’ve completed the cutting process, turn off the torch; the plasma
pilot arc will stop.
b. Metal Mesh Cutting
i. Attach the work piece and connect the earth cable with the work piece.
ii. Place the cutting nozzle onto the work piece, lift the torch up slightly from the
work piece, and turn on the switch to cut.
Page 15 of 22
c. Notice While Cutting
i. Unnecessary igniting of the pilot arc in the air will reduce the life-span of the
torch’s electrode and nozzle.
ii. It is best to start cutting at the edge of the work piece, unless you are piercing
the work piece.
iii. Keep a space between the nozzle and the work piece. Pressing the nozzle
on the work piece could cause the nozzle to stick, reducing the smoothness
of the cutting action, creating an undesirable result.
iv. Keep the torch’s nozzle vertical against the work piece, and watch to be sure
the arc is moving along the cutting line.
v. For thin materials, reduce the amperage setting to get the best cutting quality,
reduce excessive warping, and to extend the life of the electrode and nozzle.
vi. Do not rapidly switch the torch trigger ON and OFF; this will damage the pilot
arc system and work piece.
vii. The plasma cutter’s working air pressure range is 50-90 PSI. Notice: the
internal pressure switch will shut off when the air pressure falls below 50 PSI.
The switch only works when the pressure rises to 50 PSI or above.
viii. Every 4-8 hours, check the air filter on your air supply and remove excess
moisture. Too much moisture in the cutter or torch may lead to operational
trouble.
WARNING
Always unplug the power supply before checking for and removing moisture.
Maintenance
WARNING
ELECTRIC SHOCK CAN KILL!
Touching live electrical parts can cause fatal shocks or severe burns. Do not touch live
electrical parts
Wear dry, hole-free insulating gloves and body protection.
Disconnect input power before installing, maintaining or servicing this equipment.
Lockout/tagout input power according to OSHA 29 CFR 1910.147.
Maintenance Interval
Maintenance Point
Before Each Use
Inspect all cords and power cables. Replace any cords or
power cables that are damaged or cracked.
Every 3 Months
Inspect all warning and caution labels affixed to this unit. If
they are worn, torn, or otherwise unreadable, replace them.
Inspect, clean, and tighten all connections.
Every 6 months
Unplug the plasma cutter and blow out or vacuum the inside.
Page 16 of 22
Troubleshooting
WARNING
ELECTRIC SHOCK CAN KILL!
Touching live electrical parts can cause fatal shocks or severe burns. Do not touch live
electrical parts
Wear dry, hole-free insulating gloves and body protection.
Disconnect input power before installing, maintaining or servicing this equipment.
Lockout/tagout input power according to OSHA 29 CFR 1910.147.
CAUTION
Be aware that the Electrode will be electrically HOT when the Input Power Switch on the plasma cutter
is turned on.
Failure
Possible Cause
Corrective Action
Unit Does Not Power
Up
Unit Is Not Plugged In
Plug In Unit
Input Power Circuit Breaker Not On
Reset Input Power Circuit Breaker
Main Power Switch Is Defective
Replace Main Power Switch
No Pilot Arc
Low Air Supply Pressure
Check Air Supply
Adjust Gas Pressure Adjuster So The Gas
Pressure Display Reads A Minimum Of 60 PSI
Protection Indicator Is On Indicating The Machine
Is In Protection Mode
See Protection Indicator Is On’ section below
Missing Torch Head Components
Replace Missing Torch Head Components. See
the INSTALLATION OF CUTTING TORCH
section.
Plasma Torch Trigger Not Communicating with
the unit
Pull the trigger. If the work light is not on, the
torch is not communicating with the machine.
Check Trigger Connection.
Replace or Repair Torch
Plasma Torch May Be Defective
See if electrode in torch head is spring loaded. If
it is not, the torch head has seized and the torch
will need to be replaced. Install an air dryer to
your compressed air supply to prevent corrosion
of the torch head.
Arc Start Circuit Defective
Contact The Welder Help Line at 877-304-0294
Have Pilot Arc, but
Cutting Arc Does Not
Ignite
Work Piece is Painted Or Rusty
Remove All Paint And Rust
Ground Clamp Is Connected Where There Is
Remove All Paint And Rust So Ground Clamp Is
Page 17 of 22
Failure
Possible Cause
Corrective Action
Paint Or Rust
Connected To Bare Metal
Ground Clamp Is Not Electrically Connected To
The Work Piece
Make Certain The Ground Clamp Is Connected
To The Work Piece
Protection Indicator Is
On
The Internal Temperature Is Too High
Leave power on and let the fan cool the unit.
Output will continue when the unit has cooled
Input Power Voltage is Too High or Too Low
Meter Input Power Voltage. This unit must be
used with input voltage that ranges from 220V-
240V AC
Voltage Protection Range Is Incorrect
If your metered power is in the range of 220V -
240V AC, the voltage protection range may be
incorrectly set. This can be adjusted on the main
PC Board. Component VR102 can be turned
counter-clockwise to lower the minimum input
voltage threshold. Component VR101 can be
turned clockwise to increase the maximum
voltage threshold. Do not operate this unit when
input voltage is less than 170VDC or over
250VDC
Cooling Fan is Not
Working
Unit Is Not Turned On
Turn On Unit
Cooling Fan Is Defective
Replace the Cooling Fan
Control Transformer Defective
Replace Control Transformer
For Assistance, Contact The Welder Help Line At 877-304-0294
Page 18 of 22
Parts Diagram
Parts List
Reference
Part Number
Item Description
Quantity
1
105400076
HANDLE
1
2
105400077
ENCLOSURE
1
105400042
WARNING LABEL
1
125400006
NEED HELP LABEL
1
3
105400074
AIR PRESSURE SWITCH
1
4
105400078
AIR PRESSURE REGULATOR
1
5
105400079
AIR PRESSURE REGULATOR INLET
1
Page 19 of 22
Reference
Part Number
Item Description
Quantity
6
105400053
GAS CONNECTOR
1
7
105400080
GAS SOLENOID
1
8
105400081
REGULATOR SUPPORT BRACKET
1
9
105400082
INVERTER PC BOARD
1
10
105400083
UPPER RIGHT SUPPORT BRACKET
2
11
105400084
GAS VALVE CONNECTOR
1
12
105400085
BACK PANEL PLATE
1
13
105400086
COPPER NUT
1
14
105400087
INPUT POWER SWITCH
1
15
105400088
INPUT POWER SWITCH SUPPORT
1
16
105400089
BACK PLASTIC BEZEL
2
17
105400090
LOWER RIGHT SUPPORT BRACKET
2
18
105400091
FAN SUPPORT
1
19
105400092
BOX FAN
1
20
105400093
INPUT POWER CABLE
1
21
105400094
INPUT POWER CABLE SUPPORT
1
22
105400095
LOWER LEFT SUPPORT BRACKET
2
23
105400096
CABLE HOLDER
1
24
105400097
BOTTOM
1
25
105400098
OUTPUT SUPPORT PLATE
1
26
105400099
INDUCTOR
1
27
105400100
OUTPUT CONNECTION SUPPORT
1
28
105400101
ARC START CONNECTION TERMINAL
1
29
105400102
FRONT PANEL CONTROL BOARD
1
30
105400103
TRIGGER CONTROL RECEPTACLE
1
31
105400104
TORCH CONNECTOR
1
32
105400105
QUICK CONNECTOR
1
33
105400106
POTENTIOMETER KNOB
1
34
105400107
FRONT PANEL
1
125400007
NAMEPLATE P600iHD
1
35
105400108
AIR PRESSURE GUAGE
1
36
105400109
POWER OUTPUT PC BOARD
1
37
105400110
HEAT SINK SUPPORT
1
Page 20 of 22
Reference
Part Number
Item Description
Quantity
38
105400111
RECTIFIER PC BOARD
1
39
105400112
UPPER LEFT SUPPORT BRACKET
2
40
105400113
MAIN PC BOARD SUPPORT
1
41
105400114
HEAT SINK
2
42
105400115
MAIN CONTROL PC BOARD
1
105400116
PLASMA TORCH
1
105400117
TORCH DRAG SHIELD
1
105400118
TORCH COVER
1
105400119
TORCH NOZZLE
1
105400120
TORCH GAS DIFFUSER
1
105400121
GROUND CABLE AND CLAMP
1
105400122
GROUND CLAMP ONLY
1
125400008
OPERATOR’S MANUAL P600Idv
1
Replacement Parts
For replacement parts and technical questions, please call Customer Service at 1-800-222-5381.
Not all product components are available for replacement. The illustrations provided are a
convenient reference to the location and position of parts in the assembly sequence.
When ordering parts, the following information will be required: item description, item model
number, item serial number/item lot date code, and the replacement part reference number.
The distributor reserves the rights to make design changes and improvements to product lines
and manuals without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Klutch P600iHD Owner's manual

Category
Power tools
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI