MODEL 3081WRM1
Architectural Grade
Solar LED Walk Light
Solar powered illuminated garden accent light
Operates automatically during nightfall
USA Corporate Office:
Tel:
877-550-8840
Website:
www.smartsolar.com
ARCHITECTURAL GRADE SOLAR LED WALK LIGHT
Instruction ManualModel 3081WRM1
Remove the battery cover by unscrewing the four screws as
shown in figure 3. Remove and replace the two AA – NiMh
batteries as shown in figure 4. Re-assemble the unit in reverse
order and enjoy.
Notes:Be sure to check the unit is turned ON after the
batteries are replaced See Section 5 above if you have any
questions about how to check this.
Used batteries must be disposed of carefully with regard to the
environment and should NOT be put into the family waste.
7. FUNCTIONALITY PROBLEMS
Light does not switch on in darkness.
Check whether the switch is on “I” (on position).
Another light source (eg. streetlight) simulates daylight and
prevents the light from switching on automatically.
Position the module in a darker place.
Light does not switch on at all or only for a short time even
though there has been a full day of sunshine.
Battery is flat. Replace the rechargeable battery pack.
8. TECHNICAL DATA
LED description: 1 super bright white LED
LED brightness: 3.0Lm
LED consumption: 27mA
LED voltage: 3.2v
Solar panel (Voc): 4v
Solar panel (Isc): 75mA
Battery size & type: AA 1.2v Ni-Mh (2x)
Battery capacity: 700mAh
9. SPARE PARTS
Ni-Mh Battery - BPAA800
10. FULL 1 YEAR WARRANTY
If within 12 months from the date of purchase this
product fails due to a defect in material or workmanship,
Smart Solar will replace or repair it free of charge.
The warranty does not apply to:
Damage caused by accidents, abuse, poor handling, frost or
normal wear and tear. Products which have been subject to
unauthorized repair or modification or the batteries used in
this product. For further information please contact your
nearest service centre detailed on the last page of this
instruction manual.
For further information,
including parts, warranty
repair, or general
inquiries, please
contact Smart Solar:
ARCHITECTURAL GRADE SOLAR LED WALK LIGHT
Instruction Manual
ARCHITECTURAL GRADE SOLAR LED WALK LIGHT
Instruction Manual
2.41"
2.83"
1.04"
1. INTRODUCTION
Thank you for purchasing the Architectural Grade Solar LED Walk
Light. You have purchased a product that complies with the latest
and most up-to-date solar technology available. This product
complies with the European and National Standards. The relevant
certificates of conformity are held by Smart Solar To preserve
these standards and in order to maintain safety you should adhere
to the instructions for use detailed in this manual.
2. SECURITY INSTRUCTIONS
In the event of any problems arising or damage occurring as a
result of misuse the manufacturers warranty will be deemed
cancelled. The manufacturer is not responsible for any claims
or damages arising from the misuse of this product. For safety
reasons and in order to maintain standards (CE) you are prohibited
from altering or changing any component in the Architectural
Grade Solar LED Walk Light. Please follow the instructions very
carefully. For commercial applications due care and attention must
be paid to the Health and Safety Standards in your jurisdiction.
3. COMPONENTS
4. OVERVIEW
Your Solar LED Walk Light is designed for outdoor use only.
The solar module in the center of the unit converts sunlight into
electricity, which is used to charge the NiMh batteries. Once fully
charged, the unit will automatically light at dusk and automatically
turn off at dawn owe hen the batteries are fully discharged. The
light source is a specially designed super bright white LED that is
incorporated into the solar module. This LED is designed to provide
bright light at a very low power consumption. In order for the
light to operate, the unit needs to be placed in a location that
received direct sunlight. The performance of the unit is affected
by location, seasonality and weather so be sure to place in the
most optimal location possible.
5. ASSEMBLING AND USING YOUR PRODUCT
Unpack all components carefully.
Decide on a suitable location for your unit. You can mount this
item into a wooden deck or step cut-out, in soil or mulch or
permanently in concrete – please make sure that you allow
clearance around the top stainless ring so that you are able to
open the unit and replace the batteries as needed over time.
Please see Figure A for correct mounting.
1. Remove Top stainless ring and glass assembly by unscrewing
the three top screws as shown in figure 1.
2. Remove the solar module and light unit and place upside
down on a clean flat surface as shown in figure 1.
3. Press the On/Off switch once to turn on the unit as shown in
figure 2.
4. Test the unit in a dark location or by covering the light sensor
on the top of the module. If the switch is turned on correctly,
the unit will illuminate. If the unit is in darkness and does not
light, please press the switch once again and re-test in darkness.
5. Once you have properly turned in the unit, replace the center
section back in the aluminum housing and replace the top
stainless ring and glass housing and secure properly.
6. Your unit is now ready to be installed.
6. CLEANING AND MAINTENANCE
The top of the unit has a stainless steel ring and a glass cover.
This should be kept clean and free of debris at all times to
maximize the performance of your unit. You can use a soft cloth
and any mild glass cleaner to clean the top of the unit.
Removing / Replacing the batteries:
Remove top stainless ring and glass cover by unscrewing the
three screws as shown in figure 1. Remove the solar module
and light unit and place upside down on a clean flat surface
as shown in figure 2.
Firmly submerge
the LED walk light
in soil or mulch so
the face plate is the
only area exposed.
You may also
permanently install
your unit in concrete.
FIGURE 4
FIGURE 1
FIGURE 2
FIGURE 3
3 Screws
Stainless steel ring
and glass cover
Solar module and
light unit
Aluminum housing
Model 3081WRM1 Model 3081WRM1
/
