Miele F1903SF User manual

F1903SF
Miele
Brand
Miele
Model
F1903SF
Type
User manual

This manual is also suitable for

MasterCool Refrigeration
Side-by-Side Merging Combinations
For SF Models
8mieleusa.com
Page 2 of 12
Side-by-Side Merging Kit
KSK 1002
This merging kit should be used for
side-by-side installation of the following
models:
– K 18x1 SF, K 19x1 SF,
K 18x3 SF, K 19x3 SF
– F 14x1 SF, F 18x1 SF, F 19x1 SF
F 14x3 SF, F 18x3 SF, F 19x3 SF
– KF 18x1 SF, KF 19x1 SF,
KF 18x3 SF, KF 19x3SF
– KWT 16x1 SF, KWT 16x3 SF
en
3
Side-by-side
...without partition
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together. A
heating mat must also be installed. This
will help avoid condensation and
prevent damages.
...withpartition
The minimumthicknessofthe partition
is
5
/
8
"(16 mm).
If thereisapartition withathickness
from
5
/
8
"(16 mm)to6
5
/
16
" (160 mm)
betweenthe adjacentappliances, then
each appliance should be individually
installed within itsown niche using the
mountingaccessories included.
In this case,you will only need the
heating matfrom the "Merging Kit" to
avoid condensationand prevent
damages.
en
4
Product and Cut-out Dimensions
48” Side-by-Side Combination
F14X3 & K18X3
Page 3 of 12
FOR PROUD INSTALLATION
48"
24" min.
84"
29 3/4"
"8/3 5 - "2/1 3
17 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
Location Codes
E
O
Product and Cut-out Dimensions
48” Side-by-Side Combination
F14X3 & K18X3
Page 4 of 12
FOR FLUSH INSTALLATION
48"
25" min.
84"
29 3/4"
"8/3 5 - "2/1 3
17 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame)
to insure proper fit and finish
Location Codes
E
O
Product and Cut-out Dimensions
54” Side-by-Side Combination
F14X3 & K19X3
Page 5 of 12
FOR PROUD INSTALLATION
54"
24" min.
84"
35 3/4"
"8/3 5 - "2/1 3
17 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
Location Codes
E
O
Product and Cut-out Dimensions
54” Side-by-Side Combination
F14X3 & K19X3
Page 6 of 12
FOR FLUSH INSTALLATION
54"
25" min.
84"
35 3/4"
"8/3 5 - "2/1 3
17 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame)
to insure proper fit and finish
Location Codes
E
O
Product and Cut-out Dimensions
60” Side-by-Side Combination
F18X3 & K18X3
Page 7 of 12
FOR PROUD INSTALLATION
60"
24" min.
84"
29 3/4"
"8/3 5 - "2/1 3
29 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
Location Codes
E
O
Product and Cut-out Dimensions
60” Side-by-Side Combination
F18X3 & K18X3
Page 8 of 12
FOR FLUSH INSTALLATION
60"
25" min.
84"
29 3/4"
"8/3 5 - "2/1 3
29 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
E
O
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame)
to insure proper fit and finish
Location Codes
Product and Cut-out Dimensions
66” Side-by-Side Combination
F18X3 & K19X3
Page 9 of 12
FOR PROUD INSTALLATION
66"
24" min.
84"
35 3/4"
"8/3 5 - "2/1 3
29 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
Location Codes
E
O
Product and Cut-out Dimensions
66” Side-by-Side Combination
F18X3 & K19X3
Page 10 of 12
FOR FLUSH INSTALLATION
66"
25" min.
84"
35 3/4"
"8/3 5 - "2/1 3
29 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
E
O
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame)
to insure proper fit and finish
Location Codes
Product and Cut-out Dimensions
72” Side-by-Side Combination
F19X3 & K19X3
Page 11 of 12
FOR PROUD INSTALLATION
72"
24" min.
84"
35 3/4"
"8/3 5 - "2/1 3
35 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
Location Codes
E
O
Product and Cut-out Dimensions
72” Side-by-Side Combination
K19X3 & F19X3
Page 12 of 12
FOR FLUSH INSTALLATION
72"
25" min.
84"
35 3/4"
"8/3 5 - "2/1 3
35 3/4"
83 1/2" - 85 3/8"
10 1/4"
24 5/8"
1 1/8"
E
O
Notes
5 foot - 120 Volt - 15 Amp 3-wire molded plug power
supply connects lower left rear
One (1) Standard NEMA 5-15 Duplex Outlet - locate less
than 9" above finished floor
E -
O -
• KSK1002 Merging kit must be used when combining units
•All Installations must be done in accordance with local codes
• Sides of adjoining cabinets should be filled (flush to frame)
to insure proper fit and finish
Location Codes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Miele F1903SF User manual

F1903SF
Miele
Brand
Miele
Model
F1903SF
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents