Triarch 31741/16 User manual

Type
User manual

Triarch 31741/16 is a versatile lighting fixture that can be mounted on a chain or directly to the ceiling. It features a classic design with a glass shade and a variety of metal accents. The fixture is easy to assemble and can be customized to suit your specific needs.

Triarch 31741/16 is a versatile lighting fixture that can be mounted on a chain or directly to the ceiling. It features a classic design with a glass shade and a variety of metal accents. The fixture is easy to assemble and can be customized to suit your specific needs.

ASSEMBLY INSTRUCTIONS FOR 31741-16
FOR CHAIN-HUNG MOUNTING: (REFER TO FIG.1)
1. Before beginning the assembly, carefully unpack and identify all parts referring to the illustration.
2. Unravel the supply power and ground wires and pass the holes of fixture loop. Thread the fixture
loop onto the coupling at the top of fixture body. Hand tightens until snug.
3. Thread the top of stem into the coupling at the underside of fixture body. Hand tightens until snug.
4. Install proper bulbs (not provided) to the sockets referring to the markings and labels on fixture for
maximum wattage.
5. Locate the tube, cap A, check ring, glass, rubber washer and steel washer. Carefully pass the
center holes of tube, cap, glass, rubber washer and steel washer through the stem and secure
with hex nut.
6. Install cap B through the protruding stem and secure with finial.
7. Restore power to the installation point ON. Retain this sheet for future reference.
01.06
Page 1 of 2
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
FIG. 1
Fixture loop
Glass
Finial
Cap B
Steel washer
Hex nut
Rubber washer
Check ring
Cap A
Tube
Stem
Fixture body
ASSEMBLY INSTRUCTIONS FOR 31741-16
FOR CEILING MOUNTING: (REFER TO FIG.2)
1. With power to the installation point OFF, attach the crossbar with (2) mounting screws to ceiling
mounted outlet box with (2) outlet box screws.
2. Unravel the fixture supply and ground wires using wire cutters, trim the fixture supply and ground
wires to approx. 6 inches in length from where wires exit top of fixture. Trim back wire jacket
approx. 3/4 inches.
3. Remove the fixture loop from the fixture body (Refer to FIG. 1).
4. Make wires connection: (We recommend 2 people for this step) Position the fixture canopy under
the outlet box. Attach house ground wire to fixture ground wire. Proceed to attach both to the
crossbar using ground screw. Using wire connectors connect the house white wire to the fixture
supply wire (ribbed side); connect the house black (or red) wire to the fixture supply wire (smooth
side).
5. With the connections properly made, align and pass the (2) mounting screws attached to crossbar
through (2) mounting holes in the fixture canopy on the top assembly. Locate (2) ball nuts and
thread onto ends of mounting screws. Hand tightens until snug to secure fixture to ceiling. Be sure
there are no trapped or pinched wires.
6. Restore power to the installation point ON. Retain this sheet for future reference.
01.06
Page 2 of 2
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
FIG. 2
Fixture body
Stem
Tube
Cap A
Check ring
Rubber washer
Hex nut
Steel washer
Cap B
Finial
Glass
  • Page 1 1
  • Page 2 2

Triarch 31741/16 User manual

Type
User manual

Triarch 31741/16 is a versatile lighting fixture that can be mounted on a chain or directly to the ceiling. It features a classic design with a glass shade and a variety of metal accents. The fixture is easy to assemble and can be customized to suit your specific needs.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI