VOLTCRAFT DPPS-60-8 Operating Instructions Manual

Page is loading ...

39

1. Introduction ..........................................................................................................................40

2. Intended Use ........................................................................................................................41

3. Delivery content ...................................................................................................................42

4. Symbol explanation ..............................................................................................................43

5. Safety instructions ................................................................................................................44

a) Persons / Product ...........................................................................................................44

b) Miscellaneous .................................................................................................................46

6. Operating elements ..............................................................................................................46

7. Start-up ................................................................................................................................48

a) Connecting the power cable ...........................................................................................48

b) Unit installation................................................................................................................48

c) General informations.......................................................................................................48

8. Normal Operation .................................................................................................................50

a) Set current limitation .......................................................................................................50

b) Set output voltage ...........................................................................................................51

c) Connecting a load ...........................................................................................................51

9. Memory Slot Operation “Preset” and “Set” ...........................................................................53

a) Assigning memory slots with “Set” ................................................................................54

b) Reset to memory slots to default settings .......................................................................54

10. Remote Control Operation “Remote Ctrl” .............................................................................55

a) Preparation of the remote control connection .................................................................55

b) Control through external voltage source .........................................................................56

c) Control through a controllable resistance (poti) ..............................................................57

d) Remote-control output (on/off) ........................................................................................58

11. Sense function (1086562) ....................................................................................................59

12. Software installation .............................................................................................................60

13. Control with the PC software ................................................................................................60

a) Operating elements of the software and the basic operation..........................................61

b) Internal preset memory ...................................................................................................63

c) Data log...........................................................................................................................64

d) Setting .............................................................................................................................65

14. Protective measures ............................................................................................................66

a) Over-voltage protection...................................................................................................66

b) Overheating protection....................................................................................................66

c) Overload protection.........................................................................................................67

15. Maintenance and cleaning ...................................................................................................67

a) Exchanging the fuse .......................................................................................................67

16. Troubleshooting ....................................................................................................................68

17. Disposal ...............................................................................................................................69

18. Technical data ......................................................................................................................70

19. Added functions ...................................................................................................................73

a) Zeroing the unit manually................................................................................................73

b) Resetting output presets (P1/P2/P3) to factory default values ......................................74

CONTENTS

<English-start>

40

1. INTRODUCTION

Dear Customer,

In purchasing this Voltcraft® product, you have made a very good decision for which we would like

to thank you.

Voltcraft® - In the eld of measuring, charging and network technology, this name stands for

high-quality products which perform superbly and which are created by experts whose concern is

continuous innovation.

From the ambitious hobby electronics enthusiast to the professional user, products from the Voltcraft®

brand family provide the optimum solution even for the most demanding tasks. And the remarkable

feature is: we offer you the mature technology and reliable quality of our Voltcraft® products at

an almost unbeatable price-performance ratio. In this way, we aim to establish a long, fruitful and

successful co-operation with our customers.

We wish you a great deal of enjoyment with your new Voltcraft® product!

All names of companies and products are trademarks of the respective owner. All rights

reserved.

If there are any technical questions, please contact:

International: www.conrad.com/contact

United Kingdom: www.conrad-electronic.co.uk/contact

41

2. INTENDED USE

The laboratory power unit serves as a potential-free DC voltage source to operate low-voltage

consumers. The adjustable output can be tapped with up to 5 A at the front and up to the full nominal

current at the back. The front output is limited to 5 A and protected against overload. When switching

the outputs of several power supplies in series, voltages of >75 V/DC, which are dangerous to touch,

may be generated. This is why insulated lines/measuring cables must be used for safety reasons for

voltages above this. Connection on the front is performed with 4 mm safety sockets, on the back with

high-current socket screw connectors. The outputs (front and back) are connected to each other.

The connection cables used must be large enough. Where the conductor section

is too small, overheating and re may result.

The output data of the laboratory measuring devices is as follows:

Type Output voltage Output current

(Total, MAIN + AUX)

DPPS-16-30 1 – 16 V/DC 0 – 30 A

DPPS-32-15 1 – 32 V/DC 0 – 15 A

DPPS-60-8 1 – 60 V/DC 0 – 8 A

DPPS-16-40 1 – 16 V/DC 0 – 40 A

DPPS-32-20 1 – 32 V/DC 0 – 20 A

DPPS-60-10 1 – 60 V/DC 0 – 10 A

DPPS-16-60 1 – 16 V/DC 0 – 60 A

DPPS-32-30 1 – 32 V/DC 0 – 30 A

DPPS-60-15 1 – 60 V/DC 0 – 15 A

Current and voltage can be set continually through digital rotary controls using coarse and ne

settings in order to allow fast and precise value settings. The values are displayed on the structured

LC display. A power limit for constant power operation can be pre-set without a shorting bar.

The power unit can be remote-controlled. An external voltage (0 - 5 V/DC) or external potentiometer

(5 kOhm) can be used to set the output voltage and output current. The DC output is turned on and

off via the a switching contact.

Three freely programmable memory slots can be assigned to different xed voltages and current

limitations. The selection switch is located at the back of the device.

42

With the software included and the USB connection, the power supply can be controlled by a personal

computer for running cyclical operations. Up to 20 programmable sets of voltage and current at

different time durations can be programmed into the operation and the cyclical operations can be

repeated up to 999 times.

The device is overload- and short-circuit-proof and contains a safety temperature cut-off. The

laboratory power unit is designed in compliance with protection class 1. It is only approved for

connection to shockproof sockets with protective grounding and an alternating current of 230 V/AC

commonly used in households.

Unauthorised conversion and/or modication of the device are inadmissible because of safety and

approval reasons (CE). Any usage other than described above is not permitted and can damage the

product and lead to associated risks such as short-circuit, re, electric shock, etc. Please read the

operating instructions thoroughly and keep them for further reference.

Observe all safety instructions and information within this operating manual.

3. DELIVERY CONTENT

• Laboratory power supply

• Remote connection socket

• Power cable with grounding contact

• USB cable

• CD (software)

• Operating instructions

Up-to-date Operating Instructions:

1. Open www.conrad.com/downloads in a browser or scan the displayed

QR code.

2. Select document type and language and enter the item number into

the search eld. After submitting the query you can download displayed

records.

43

4. SYMBOL EXPLANATION

An exclamation mark in a triangle indicates important instructions in this operating manual

which absolutely have to be observed.

The triangle containing a lightning symbol warns of danger of an electric shock or of the

impairment of the electrical safety of the device.

The symbol can be found when you are to be given tips and information on operation.

Only to be used in dry indoor areas.

This product has been CE-tested and meets the required European guidelines.

Grounding wire connection; this screw may not be loosened.

44

5. SAFETY INSTRUCTIONS

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on proper

handling in this manual, we assume no liability for any resulting personal injury or

damage to property. Such cases will invalidate the warranty/guarantee.

a) Persons / Product

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. These may become

dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed if the

product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can

damage the product.

• Also observe the safety and operating instructions of any other devices which are

connected to the product.

• Products operated using the mains voltage must be kept out of the reach of children.

For this reason, be particularly careful when using the product in the presence of

children. They may try to stick objects into the device through openings in the housing.

This poses a risk of death by electric shock.

• Never pour liquids over electrical appliances and never leave objects lled with liquids

(e.g. vases) on it or in the vicinity. There is a high risk of re or life-threatening electric

shock.

• Operate the product in dry interior spaces only. It must not get damp or wet. Otherwise

there is a risk of a life-threatening electric shock!

• In schools, training facilities, hobby or self-service workshops, handling of electrical

devices must be monitored by trained personnel.

• When operating on commercial premises, the relevant accident prevention regulations

of workers’ compensation boards for electrical equipment must be observed.

• Live parts may become exposed when opening covers or removing parts. You must

therefore disconnect the product from all power sources before performing any

maintenance or repairs. Capacitors in the device can still carry a charge even if the

device has been disconnected from all voltage sources.

45

• Always lay the cables so that nobody can trip over or become entangled in them. This

poses a risk of injury.

• When working with power supplies or chargers, do not wear any metallic or conductive

chains, bracelets, rings etc. Never connect the power supply or charger with humans

or animals.

• Check the product for damage(s) each time before use. If you discover any damages,

do not use the product. Disconnect the power supply and unplug the mains adapter

from the wall outlet. Then bring the product to a specialised workshop.

• Use only a proper mains socket (230V~/50Hz) connected to the public power supply.

• The mains outlet must be located near to the device and be easily accessible.

• Do not touch the mains cable if it is damaged. First, power down the respective mains

socket (e.g. via the respective circuit breaker) and then carefully pull the mains plug

from the mains socket. Never use the product if the mains cable is damaged.

• A damaged mains cable may only be replaced by the manufacturer, a workshop

commissioned by the manufacturer or a similarly qualied person, so as to prevent any

danger.

• Never plug in or unplug the mains plug when your hands are wet.

• Do not pull the mains adapter out of the wall outlet by its cable!

• The plug must be pulled out of the socket under the following conditions:

- before cleaning the product

- during a thunder storm

- if the product is not being used over a long period.

• Make sure that the product is provided with adequate ventilation during operation. Do

not cover the ventilation openings with magazines, blankets, curtains or similar. Keep a

minimum distance of approx. 15 cm from other objects.

• When setting up the product, make sure that the cable is not pinched, kinked or

damaged by sharp edges.

• Make sure there are no devices with strong electric or magnetic elds such as

transformers, motors, cordless telephones and radio-controlled devices in the vicinity

of the product as these can inuence the product.

• Do not operate the product in places or rooms with unfavourable ambient conditions.

This can damage the sensitive electronics found inside the product and can potentially

pose life-threatening risks. Poor ambient conditions are:

- High humidity (> 80 % relative, condensation)

- Humidity, dust, ammable gases, solvent vapours, benzine

- High ambient temperatures (> approx. +50 ºC)

- Electromagnetic elds (motors, transformers, audio systems for model building etc.)

or electrostatic elds

46

• The product should not be used immediately after it has been brought from an area

of cold temperature to an area of warm temperature. Condensed water might destroy

the product. Wait until the product adapts to the new ambient temperature before use.

b) Miscellaneous

• Consult an expert when in doubt about operation, safety or connection of the device.

• Maintenance, modications and repairs are to be performed exclusively by an expert

or at a qualied shop.

• If you are not sure about the correct connection or use, or if questions arise which

are not covered by these operating instructions, please do not hesitate to contact our

technical support or another qualied specialist.

6. OPERATING ELEMENTS

1. LED panel meter display with C.V. (Constant voltage) and C.C (Constant current) indicator

2. Control indicator REAR CONTROL (Control over rear side)

3. Control knob VOLTAGE (Output voltage)

4. Control knob CURRENT (Output current)

5. On/Off switch POWER (on/off)

6. Terminals AUX. OUTPUT 5A MAX. (Auxiliary output terminals)

7. Terminals MAIN OUTPUT (Output terminals)

8. Selection switch MODE (Mode selection)

9. Selection switch RECALL (Recall)

10. Remote control terminal Remote Control

11. Cooling fan protective grille

12. Power input and fuse

13. USB port

14. Terminals SENSE (Sensor terminals)

Page is loading ...

48

7. START-UP

The laboratory power unit is not a charger. To charge batteries, use suitable

chargers with a charging current cut-off.

During a longer period of operation under nominal load, the surface of the housing

will heat up. Attention! Risk of burns! Therefore, make sure that there is adequate

ventilation of the power unit and never operate it partly or fully covered to avoid

any damage.

When connecting a consumer, ensure that it is not connected when switched on.

A switched-on consumer can result in sparks when connecting to the output

terminals of the power unit, which in turn can damage the sockets or the connected

cables and/or their clamps.

If your power unit is not required, switch it off and disconnect it from the mains.

The displays remain on for a few seconds after it is switched off to unload the

internal capacitors and to store the last parameters that were set.

Always ensure a sufcient conductor cross-section for the DC connection lines,

since overload may cause re in the line.

a) Connecting the power cable

1. Connect the supplied grounding mains cable to the power input (12) on the power unit. Ensure

a tight t.

2. Connect the power cable to a shockproof mains socket with protective grounding. The maximum

length of the power cable to the outlet must not exceed 3 m.

b) Unit installation

Place the laboratory power unit on a stable, level and robust surface. Make sure that ventilation slots

in the casing are not covered up.

c) General informations

The laboratory power unit is micro-processor-controlled and is operated through two digital controls

(incremental encoders without end position) with sensor function. This enables ne and coarse control

via a control.

49

After the device switches on, a system check is performed. The test status is displayed on the two

displays. The displays are in the following order:

Display of the current software state.

Segment test to determine if the display works with

all its individual segments.

Then the LED displays C.V., C.C. and REAR

CONTROL are tested.

System test of the protective measures starts.

The over-voltage protection is tested.

The over-load protection is tested.

The over-temperature protection is tested.

Fan test The fan is shortly tested throughout the

speed range.

For a short time, the fan speed increases audibly.

The remote control function for “output out” is

tested.

After this step, the device switches to the regular

operating display mode.

50

The power unit enables operation in 4 modes. These modes are selected by the selection switch

MODE (8) slider on the back. The following modes are possible:

Normal Normal operation. Voltage and current are adjusted on the front.

Preset Memory slot operation Three xed voltages can be stored in the device and

directly selected through this Preset function. The memory slot is selected with

the selection switch RECALL (9). The front controls are inactive.

Remote Ctrl Remote control operation. The power unit can be remote-controlled via

an external voltage or external potentiometer. The remote settings can be

performed for voltage and current. The front controls are inactive.

Set Settings operation. The three preset slots can be programmed freely. Select the

memory slot with the selection switch RECALL (9) and make the settings using

the control knobs (3, 4).

The separate operating modes are described in more detail in the following.

8. NORMAL OPERATION

In normal operation, the power unit can be operated through the front

controls. Ensure that the selection switch MODE is in the Normal position.

Remove any connected consumers from output (6 or 7).

Switch on the power unit at the On/Off switch POWER (5). The display (1)

lights up, and after a short self test, the current and voltage displays appear.

Set the current limitation before setting any voltages. If the current value is too high, your

connection lines can be damaged; if it is too low (<1 A), the output voltage can be limited.

a) Set current limitation

Limiting the output current is a protection mechanism to protect the consumer or connection cables.

Current limitation can be pre-set at the output without any short circuit. The power unit then supplies

the maximum current set.

1. Remove any connected consumers from the power unit.

2. Switch on the power unit at the On/Off switch POWER (5). The display (1) lights up, and after a

short self test, the current and voltage displays appear.

3. Set the current limitation at the control knob CURRENT (4) according to your application.

4. Turn the control and a current limitation value appears.

51

Where no setting is made within 2 seconds, the display switches back to the current

current display.

5. Turn the control to the left or right to set the current limitation. After switching on, the ne settings

area (0.1 A) is always active. This is indicated by a slightly lighter digit. Press the rotary control

slightly from the front. The decimal position (1.0 or 0.1) of the setting range changes each time you

press. Turning changes the value.

6. Settings can be made coarsely (whole numbers) or ne (by tenths).

7. Where the desired current value was set, the display switches back to normal display after 2 seconds.

If the preset current is reached in normal operation, the power unit switches to current limitation

mode and reduces the voltage value. This operation is signalled with the red status display

C.C. (1).

b) Set output voltage

The output voltage can be set at the control knob VOLTAGE (3) control. The coarse and ne control

is performed in the same way as for setting the current limitation.

With the large control range, it is possible that the voltage setting takes approx.

1- 2 seconds to switch from a high to a low voltage value.

In normal mode the device operates in constant voltage mode. This means that the power

unit emits a constant, preset output voltage. This operation is indicated with a green status

LED C.V. (1).

c) Connecting a load

When connecting a consumer, make sure that it is connected to the power unit when

switched off. The maximum current consumption of the device to be connected

must not exceed the capacity indicated in the technical specications.

For serial connection of the outputs with several power supplies, the resulting

voltages can be fatal on contact (> 75 V/DC). As of this voltage, you may only use

insulated accessories.

Avoid the use of non-insulated metallic cables and contacts. All these exposed

areas must be covered with suitable, ame-resistant insulation materials or by other

measures and be protected from direct contact and short circuits.

Ensure a sufcient cable diameter for the intended current.

The power unit has two outputs. These outputs always have the same output voltage. The difference,

however, is in the current carrying capacity.

52

Max. 5 A shall be tapped at the terminals AUX. OUTPUT 5A MAX. (6).

A PTC overcurrent protection protects those terminals against overloading and

interrupts the current supply when triggered (>5 A). To reset the unit, immediately

turn it off and let it cool down to room temperature before using it again.

The terminals MAIN OUTPUT (screw sockets) (7) on the back are indicated for full

nominal current. From an output current of 5 A, the screw clamp function of the rear

sockets is recommended to avoid overheating of the plug sockets.

1. Remove any connected consumers from the output.

2. Switch on the power unit at the On/Off switch POWER (5). The operating display (1) lights up and

the current and voltage display appears on the display.

3. Set the parameters according to your specications as described in the chapter “Start-Up”.

4. Check once more that the correct output voltage is set.

5. Connect the plus pole (+) of the consumer with the red socket “+” and the minus pole (-) of the

consumer with the black socket “-” of the respective output (front = AUX. OUTPUT 5A MAX. (6),

rear = MAIN OUTPUT (7)).

Now you can switch on the connected consumer.

The current consumption of the connected consumer is displayed in Ampere (A) in the display (1).

53

9. MEMORY SLOT OPERATION “PRESET” AND “SET”

Three xed voltages, including current settings, can be stored in the device with the Set function and

directly selected through the Preset function.

Ex works, all three memory slots (P1, P2, P3) are preset.

They are assigned as follows:

Memory

Type

P1 P2 P3

Voltage Current Voltage Current Voltage Current

DPPS-16-30 5 V Maximum 13.8 V Maximum 15 V Maximum

DPPS-32-15 5 V Maximum 13.8 V Maximum 25 V Maximum

DPPS-60-8 5 V Maximum 13.8 V Maximum 55 V Maximum

DPPS-16-40 5 V Maximum 13.8 V Maximum 15 V Maximum

DPPS-32-20 5 V Maximum 13.8 V Maximum 25 V Maximum

DPPS-60-10 5 V Maximum 13.8 V Maximum 55 V Maximum

DPPS-16-60 5 V Maximum 13.8 V Maximum 15 V Maximum

DPPS-32-30 5 V Maximum 13.8 V Maximum 25 V Maximum

DPPS-60-15 5 V Maximum 13.8 V Maximum 55 V Maximum

Make sure that no consumers are connected.

The memory can also be set via the software provided, check the chapter “Control with the

PC software”.

1. Activate the Preset function through the selection switch MODE (8) on the rear.

2. Put the switch in the Preset position. The front LED

indicator REAR CONTROL (2) lights up. The front

control knobs are now inactive.

3. Select the respective memory slot P1, P2 or P3 on

the rear selection switch RECALL (9). The

respective

output voltage is indicated on the display (1).

4. Now you can connect and switch on the consumer.

2

3

54

5. For deactivating the xed voltage function, slide the selection switch MODE (8) back to the Normal

position. The control indicator REAR CONTROL (2) goes out. The device switches back to normal

power unit operation (always remove DC consumers before!).

a) Assigning memory slots with “Set”

All three memory slots can be assigned user-specic values for output voltage and current limitation.

Make sure that no consumers are connected.

1. Activate the Set function through the MODE (8)

slider on the rear. Put the switch in the Set position.

The front control indicator REAR CONTROL (2)

lights up. Select the respective memory slot P1,

P2 or P3 on the selection switch RECALL (9).

The respective values for current and voltage are

indicated on the display (1).

2. The front control knobs (3 and 4) can be used to

set the desired output voltage and current limitation.

3. If required, repeat these steps with the other memory slots.

4. When all parameters are set, slide the selection switch MODE (8) back to the Preset position for

xed voltage operation or to the Normal position for standard operation.

b) Reset to memory slots to default settings

1. Switch off the power unit.

2. Press the two rotary controls on the front at the same time and keep them pressed.

3. Switch on the power unit. When the displays light up, let go of both rotary controls. The default

settings for the parameters are active again.

2

3

55

10. REMOTE CONTROL OPERATION “REMOTE CTRL”

Through the built-in remote control terminal Remote control (10), the voltage and current can be

set through an external voltage source or an external adjustable resistance (short “poti”). The remote

control is connected on the remote control terminal Remote control (10). There is a remote socket

included for connection.

In remote-controlled operation, the current control path must also be connected,

since the output otherwise switches to the current limitation mode “C.C.” and limits

the output voltage.

a) Preparation of the remote control connection

1. Turn the lateral screw of the supplied socket and remove the front, black contact socket turning

it slightly.

2. Draw ve connecting cables with a conductor cross-section of at least 0.34mm

2

through the metal

sleeve from the rear. Carefully solder these cables to the soldering lugs nos.1, 2, 3, 4 and 5 of the

black contact socket. Ensure that no short circuits are created.

The numbers of the soldering lugs are indicated on the black insulator.

Mark the loose ends of the cables with the corresponding contact numbers (1-5) to avoid confusion.

Insert the black contact jack in the reverse order into the metal sleeve and screw them tight.

The contacts are assigned as follows:

Contact 1 Internal control voltage + 5 V/DC (<50 mA)

Contact 2 Voltage setting

Contact 3 Current setting

Contact 4 Reference ground (“Ground”)

Contact 5 Output on / off

Contact 6 – 8 Not assigned

56

b) Control through external voltage source

The power unit can be remote-controlled with an external voltage source from 0 to 5 V/DC throughout

the range for voltage and current.

Proceed as follows for connection:

Connect the connecting cables of the remote sockets as illustrated:

V

Voltage setting “V”

• Connection 2 to the plus pole (+) of the

external control voltage.

• Connection 4 to the minus pole (-) of the

external control voltage.

Current setting “I“:

• Connection 3 to the plus pole (+) of the

external control volltage.

• Connection 4 to the minus pole (-) of

the external control volltage

The voltage on the remote control connection must not exceed 5 V.

The connections must not be shorted.

1. Switch off the power unit and then connect the remote socket to the

remote control terminal Remote Control. Screw on the external

fastening ring.

2. Turn the voltage of the external voltage source to 0 V.

3. Switch on the power unit.

4. Put the selection switch MODE (8) on the rear into the Remote Ctrl

position. The control indicator REAR CONTROL (2) is lit.

5. The desired output value can now be set through the external voltage

source. Control the complete adjustment area for correct function. The

output voltage can be monitored in the display.

Short-circuit the rear terminals MAIN OUTPUT (7) with a sufciently thick cable for checking

the current control (at least 8 mm

2

). Check the entire setting for proper operation.

If this remote control function is no longer required, put the selection switch MODE (8) to the Normal

position.

57

c) Control through a controllable resistance (poti)

The power unit can be remote-controlled with an external poti (5 Kohm) throughout the range for

voltage and current.

Proceed as follows for connection:

Connect the connecting cables of the remote sockets as illustrated.

Voltage setting “V”

• Connection 1 at one end of the

resistance.

• Connection 2 at the centre sliding contact

of the resistance.

• Connection 4 at the second end of the

resistance.

Current setting “I“:

• Connection 1 at one end of the

resistance.

• Connection 3 at the centre sliding

contact of the resistance.

• Connection 4 at the second end of the

resitance.

Connections 1 and 4 must not be short-circuited.

1. Switch off the power unit and then connect the remote socket to the

remote control terminal Remote Control. Screw on the external

fastening ring.

2. Switch on the power unit.

3. Put the selection switch MODE (8) on the rear into the Remote Ctrl

position. The control indicator REAR CONTROL (2) is lit.

4. The desired output values can now be set through the external poti.

Control the complete adjustment area for correct function. The output

voltage can be monitored in the display.

Short-circuit the rear terminals MAIN OUTPUT (7) with a sufciently thick cable for checking

the current control (at least 8 mm

2

). Check the entire setting for proper operation.

If this remote control function is no longer required, put the selection switch MODE (8) to the Normal

position.

58

d) Remote-control output (on/off)

The DC output can be turned on and off via the a switching contact.

Proceed as follows for connection:

1. Connect the connecting cables of the remote sockets as illustrated.

2. Contact connections 4 and 5 with an isolated switching contact.

3. When the output is turned off, the status displays “C.V.” and “C.C.” (1) will ash. The display will

then show the current settings of the output voltage and the output current (1).

4. When the output is turned off, you can set the output values with the control knobs for voltage

(VOLTAGE) (3) and current limiting (CURRENT) (4).

No voltage must be applied to contacts 4 and 5.

5. Switch off the power unit and then connect the remote socket to the rear

remote connection. Screw on the external fastening ring.

6. Switch on the power unit.

7. Put the selection switch MODE (8) on the rear into the Remote Ctrl

position. The control indicator REAR CONTROL (2) display is lit.

8. If the switching contact is open, the DC output is active; if it is closed,

the DC output is switched off. Check the switching function for correct

function.

9. When the DC output is switched off, “O P OFF” is displayed.

10. If this remote control function is no longer required, put the selection

switch MODE (8) to the Normal position.

59

11. SENSE FUNCTION (1086562)

The sense function is only available with Item No. 1086562.

The sense function is an automatic voltage control for the rear high-current output (MAIN OUTPUT) (7).

For this, two separate measuring cables are connected parallel to the connecting cables. The

potential drop which occurs on the connecting cables is measured on these two measuring cables.

The laboratory power unit automatically compensates for this voltage drop so that the actually set

voltage is supplied to the consumer.

Proceed as follows for connection:

1. Turn off the power supply unit and the consumer.

2. Always connect the supply cables from the power unit to the consumer rst. Pay attention to

correct polarity.

3. Press the clamp release on the rear terminals SENSE (14) inwards with a small screwdriver and

insert the cables into the terminal openings. Check that they are plugged rmly.

4. Now connect the two sense cables to the consumer observing the correct polarity. The conductor

cross-section for the sense cables must be at least 0.34 mm

2

.

5. Always slacken the connection in the reverse order (rst of all sense cables and then the

connecting cables).

1086562

Make sure that you contact the sense cables as close as possible to the connecting

point of the consumer. Observe correct polarity.

Never short-circuit the sense cables.

Page is loading ...

VOLTCRAFT DPPS-60-8 Operating Instructions Manual

This manual is also suitable for

VOLTCRAFT DPPS-60-8 Operating Instructions Manual

in other languages

Related papers

Other documents