Signature Hardware SH214883 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
SH214883
Type
Installation guide

This manual is also suitable for

Signature Hardware SH214883 is a bridge faucet, a type of kitchen faucet that mounts on the counter or sink, as opposed to the wall. It features a side sprayer, which is a separate nozzle that can be used to spray water in a variety of directions, making it ideal for rinsing dishes or cleaning the sink. The faucet has hot and cold water inlets, and the water flow can be diverted from the spout to the side sprayer. The faucet is made of durable materials and is easy to install.

Signature Hardware SH214883 is a bridge faucet, a type of kitchen faucet that mounts on the counter or sink, as opposed to the wall. It features a side sprayer, which is a separate nozzle that can be used to spray water in a variety of directions, making it ideal for rinsing dishes or cleaning the sink. The faucet has hot and cold water inlets, and the water flow can be diverted from the spout to the side sprayer. The faucet is made of durable materials and is easy to install.

1Bridge Faucet Installation Instructions
BRIDGE FAUCET
INSTALLATION INSTRUCTIONS
Before installing, read entire Bridge Faucet Installation Instructions. Observe all local building and safety codes.
For the following installation instructions for your new Bridge Faucet it is assumed that any old xtures have been
removed and any repairs or modications to the water supply have been completed.
Unpack and inspect the product for any shipping damages. If you nd damages, do not install. Contact Customer
Service at 1-866-855-2284. If you need assistance or have questions while installing your Bridge Faucet, contact
Customer Service.
We recommend consulting a professional if you are unfamiliar with installing kitchen xtures. Signature Hardware
accepts no liability for any damage to the oor, walls, plumbing or for personal injury during installation.
Turn off the water supply at the sink where the new faucet is being installed.
TOOLS AND MATERIALS:
INSTALLATION
1. Attach the bottom of the handle assembly to the faucet if not already attached, making sure to include any rubber
washers or sealing gaskets provided. Remove the lock nuts from the bottom of the threaded handle shanks and insert
through the mounting holes.
2. Hand-tighten washers (if included) and hex nuts from underneath the sink to secure.
3. Check to make sure the faucet is properly aligned and adjust as needed. When the faucet is in the proper position,
nish tightening the hex nuts with your adjustable wrench.
4. If your faucet features a side spray, install by inserting the sprayer housing, and rubber sealing gasket through the
mounting hole. Secure by tightening the lock nut from underneath the sink. If your faucet does not have a side spray move
on to step 6.
5. Attach the spray nozzle to the spray hose if not already attached and insert through the sprayer housing. Attach the
hose to the spray hose outlet on the faucet.
Tip: Before you connect the spray hose to the faucet, make sure that it is in a position that will allow you to pull it out
easily without getting caught on any other xtures under the sink.
6. Hand tighten to attach the hot and cold water feed tubes to the water inlets; hot water is always on the left and cold wa-
ter is always on the right. Give a ¼ turn with pliers or wrench, but don’t over tighten. Curve tubes as necessary to ensure
there are no kinks or knots.
Tip: Place plumber’s tape on hoses and pipes before you attach supply lines to ensure leak-free connections.
7. After all connections have been made, turn on the water supply, check to make sure that all connections are tight (no
water should be leaking) and that the hot and cold supplies are working correctly. Turn the faucet on and allow the water
to ow through the spout for approximately 60 seconds. Divert the water to the spray hose and allow the water to ow
through the hose for approximately 60 seconds.
Adjustable Wrench Teon Pipe Tape Basin Wrench
  • Page 1 1

Signature Hardware SH214883 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
SH214883
Type
Installation guide
This manual is also suitable for

Signature Hardware SH214883 is a bridge faucet, a type of kitchen faucet that mounts on the counter or sink, as opposed to the wall. It features a side sprayer, which is a separate nozzle that can be used to spray water in a variety of directions, making it ideal for rinsing dishes or cleaning the sink. The faucet has hot and cold water inlets, and the water flow can be diverted from the spout to the side sprayer. The faucet is made of durable materials and is easy to install.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents