Baldor-Reliance GA16 & 20 Pedestal Bases Assembly Instructions

Brand
Baldor-Reliance
Model
GA16 & 20 Pedestal Bases
Type
Assembly Instructions

Baldor-Reliance GA16 & 20 Pedestal Bases provide a stable and secure platform for mounting grinders and buffers. Constructed from heavy-duty materials, these pedestals are designed to withstand the rigors of industrial environments. With a weight capacity of 61 lbs for the GA16 and 128 lbs for the GA20, these pedestals can accommodate a wide range of grinders and buffers. The adjustable top plate allows for precise positioning of the mounted equipment, ensuring optimal performance and safety. Installation is straightforward and requires minimal tools, making it easy to set up and use.

Baldor-Reliance GA16 & 20 Pedestal Bases provide a stable and secure platform for mounting grinders and buffers. Constructed from heavy-duty materials, these pedestals are designed to withstand the rigors of industrial environments. With a weight capacity of 61 lbs for the GA16 and 128 lbs for the GA20, these pedestals can accommodate a wide range of grinders and buffers. The adjustable top plate allows for precise positioning of the mounted equipment, ensuring optimal performance and safety. Installation is straightforward and requires minimal tools, making it easy to set up and use.

MN901
Assembly Instructions For GA16 and GA20 Pedestals
1MN901
Installation When you receive your unit, there are several things you should do immediately.
1. Observe the condition of the shipping container and report any damage immediately to the commercial carrier
that delivered the product.
2. Verify that the part number you received is the same as the part number listed on your purchase order.
3. Tools required − 9/16 in socket and drive, 3−in extension, and torque wrench.
4. Parts Required −
Part Description (QTY) GA16 Pedestal GA20 Pedestal
Top Plate (1) HA6069A01 G8BA1001A01
Pedestal (1) G8BA5000A03 G8BA5000A01
Base Plate (1) G6BA1001A01 G8BA1002A01
Screws (6) 3/8−16 x 1−1/4” 3/8−16 x 1−1/2”
Lock washers (6) 3/8” 3/8”
SAFETY NOTICE: WARNING statements describe conditions that may lead to personnel injury including potentially fatal injuries if the
machine is not properly used and warnings are not properly followed.
Caution statements describe conditions that may lead to equipment damage.
WARNING: The GA16 pedestal weighs 61 lbs. the GA20 pedestal weighs 128 lbs. Use appropriate lift equipment or
several people to move and assemble. Use proper lift procedures and avoid back strain. Heavy objects can
cause serious strain and crushing of fingers or other body parts. Be careful, never place fingers or other
body parts under heavy items and avoid injury.
Assembly Refer to Figure 1 during assembly.
1. Remove parts from carton.
2. Place a lock washer on each screw.
3. Place pedestal in vertical position on a at, level surface
(oor) so that the pedestal is stable and the labels may be
read correctly (Figure 1).
4. Place the top plate on top of the pedestal, and align the
3 screw holes in the top plate with the 3 tapped holes in the
pedestal.
5. Secure the top plate to the pedestal using 3 screws and
lock washers supplied. Tighten the screws to
19.1 to 23.3 lb−ft using torque wrench.
6. Rotate the pedestal/top plate assembly upside down. Be
sure the assembly is stable and that it will not tip over.
7. Place the Base Plate on the pedestal, and align the 3 screw
holes in the Base Plate with the 3 tapped holes in the
pedestal.
8. Attach the Base Plate to the pedestal using 3 screws and
lock washers supplied. Tighten the screws to
19.1 to 23.3 lb−ft using torque wrench.
9. Rotate the pedestal assembly to it’s normal position so that
the Base Plate is down.
10. Secure the pedestal Base Plate to the oor (hardware not
provided) before mounting the grinder or buffer to the
pedestal.
11. Secure the grinder or buffer to the pedestal, refer to manual
for the grinder or buffer.
Figure 1 Pedestal Components
Pedestal
Top Plate
Base Plate
Baldor Electric Company
P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.646.4711, Fax (1) 479.648.5792, International Fax (1) 479.648.5895
www.baldor.com
© Baldor Electric Company
MN901
All Rights Reserved. Printed in USA.
10/05
  • Page 1 1
  • Page 2 2

Baldor-Reliance GA16 & 20 Pedestal Bases Assembly Instructions

Brand
Baldor-Reliance
Model
GA16 & 20 Pedestal Bases
Type
Assembly Instructions

Baldor-Reliance GA16 & 20 Pedestal Bases provide a stable and secure platform for mounting grinders and buffers. Constructed from heavy-duty materials, these pedestals are designed to withstand the rigors of industrial environments. With a weight capacity of 61 lbs for the GA16 and 128 lbs for the GA20, these pedestals can accommodate a wide range of grinders and buffers. The adjustable top plate allows for precise positioning of the mounted equipment, ensuring optimal performance and safety. Installation is straightforward and requires minimal tools, making it easy to set up and use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents