Harbor Freight Tools Mesh Deck Steel Wagon User manual

Brand: Harbor Freight Tools

Model: Mesh Deck Steel Wagon

Type: User manual

Page 2 For technical questions, please call 1-800-444-3353. Item 38137

Specications

Capacity 1000 lb.

Wagon Deck 4 FT. long, 2 FT. wide

Wheels 10 IN. Turf-Tread Pneumatic Tires

IMPORTANT SAFETY INFORMATION

WARNING Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in serious injury.

Save all warnings and instructions for future reference.

1. DO NOT ALLOW CHILDREN TO PLAY WITH

OR AROUND THE WAGON. NOT A TOY.

2. Do not ride on this wagon.

3. Do not exceed 1000 lb. weight capacity,

evenly distributed.

4. When loading and unloading the wagon,

be careful of the balance of the wagon.

5. Be careful of the Handle which can tip

and fall from the upright position.

6. Chock the four wheels before loading

or unloading the wagon.

7. Wear ANSI-approved safety goggles during assembly.

8. Inspect before every use; do not use

if parts are loose or damaged.

9. Maintain product labels and nameplates. These carry

important safety information. If unreadable or missing,

contact Harbor Freight Tools for a replacement.

SAVE THESE INSTRUCTIONS.

Assembly

1. Attaching Rear Bracket to Tray

Turn the Tray (B) upside down so that the exposed

screw holes can be seen. Attach the Rear Bracket (C)

to the Tray using two Bolts (M8x38) (I) - for connection

of the main axle portion of the Rear Bracket, and four

Bolts (M6x20) (J) - for connection of the support arms

of the Rear Bracket. All bolts receive both a Spring

Washer (M/O), Flat Washer (N/P), and Nut (K/L).

Rear

Bracket (C)

Tray (B)

Main Connection:

Bolt M8x38 (I),

Flat Washer (P),

Spring Washer (O),

Nut (L)

Support Arm

Connection:

Bolt M6x20 (J),

Flat Washer (N),

Spring Washer (M),

Nut (K)

2. Attaching Turning Bracket to Tray

Attach the Turning Bracket (D) to the Tray using

two Bolts (M8x38) (I) - for connection of the main

axle portion of the Turning Bracket, and two Bolts

(M6x20) (J) - for connection of the front portion

of the Turning Bracket. The rear portion of the

Turning Bracket is attached to the Tray with 2 Bolts

(M6x20) (J). All bolts receive a Spring Washer

(M/O), Flat Washer (N/P), and Nut (K/L).

Main

Connection:

Bolts (M8x38) (I)

Spring Washer (O)

Flat Washer (P)

Nut (L)

Support Arm

Connection:

Bolts (M6x20) (J)

Spring Washer (M)

Flat Washer (N)

Nut (K)

Turning

Bracket (D)

Page 3For technical questions, please call 1-800-444-3353.Item 38137

3. Attaching Handle

Attach the Handle (E) to the Turning Bracket

by using Bolt (M6x63) (H), Spring Washer

(M), Flat Washer (N) and Nut (K).

Turning

Bracket (D)

Handle (E)

Spring

Washer (M)

Flat Washer (N)

Nut (K)

Bolt (M6x63) (H)

4. Attaching Wheels

Install the four Wheels (F) by placing each wheel

on the axle portion of the Turning Bracket and

the Rear Bracket. Secure each Wheel with a Flat

Washer (M16) (Q) and a Split Pin (M3x30) (R).

Axle

Flat Washer (M16) (Q)Split Pin (M3x30) (R)

Wheels (F)

5. Test all bolts and nuts for tightness before turning the

wagon over on its wheels.

Roll the wagon to check for proper wheel operation.

Periodicallychecktireination(maximumtireination

is 30 PSI). Periodically lubricate wheel axles.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A

REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY

KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT

ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY

THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT

OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Part Description Qty

B Tray 1

C Rear Bracket 1

D Turning Bracket 1

E Handle 1

F Wheel 4

G Support Arm 2

H Bolt M6x63 1

I Bolt M8x38 4

J Bolt M6x20 8

K Nut M6 9

L Nut M8 4

M Spring Washer M6 9

N Flat Washer M6 9

O Spring Washer M8 4

P Flat Washer M8 4

Q Flat Washer M16 4

R Split Pin M3x30 4

Record Product’s Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed and shown

for illustration purposes only, and are not

available individually as replacement parts.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If

ourinspectionveriesthedefect,wewilleitherrepairorreplacetheproductatourelectionorwemayelect

to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return

repaired products at our expense, but if we determine there is no defect, or that the defect resulted from

causes not within the scope of our warranty, then you must bear the cost of returning the product.

Thiswarrantygivesyouspeciclegalrightsandyoumayalsohaveotherrightswhichvaryfromstatetostate.

Parts List and Assembly Diagram

Harbor Freight Tools Mesh Deck Steel Wagon User manual

Harbor Freight Tools Mesh Deck Steel Wagon User manual

Harbor Freight Tools Mesh Deck Steel Wagon User manual

Related papers

Other documents