King Canada KC-5007 User manual

Brand: King Canada

Model: KC-5007

Category: Power tools

Type: User manual

King Canada KC-5007 is a 10-inch table saw designed for non-commercial use. It features a powerful motor and a large working surface, making it suitable for a variety of cutting tasks. The saw's blade can be tilted up to 45 degrees, allowing for angled cuts. It also comes equipped with a miter gauge and a rip fence, which help to ensure accurate and precise cuts.

10” TABLE SAW

INSTRUCTION MANUAL

MODEL: KC-5007

IMPORTANT INFORMATION

-YEAR

LIMITED WARRANTY

FOR THIS 10” TABLE SAW

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this tool are available at our authorized KING CANADA service centers across Canada. For servicing, contact

or return to the retailer where you purchased your product along with your proof of purchase.

LIMITED TOOL WARRANTY

KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to

the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free

from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents,

repairs or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or

for incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product

or part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA

will either repair or replace the product.

KING CANADA

OOLS INC. DOR

VAL, QUEBEC, CANADA H9P 2Y4

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS

1. KNOW YOUR TOOL

ead and understand the owners manual and labels affixed to

the tool. Learn its application and limitations as well as its

specific potential hazards.

2. GROUND THE TOOL.

This tool is equipped with an approved 3-conductor cord and

a 3-prong grounding type plug to fit the proper grounding type

receptacle. The green conductor in the cord is the grounding

wire.

NEVER connect the green wire to a live

terminal.

3. KEEP

GUARDS IN PLACE.

Keep in good working order, properly adjusted and aligned.

4. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents. Make sure the

floor is clean and not slippery due to wax and sawdust

build-up.

6. AVOID DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations or expose

them to rain. Keep work area well lit and provide adequate

surrounding work space.

7. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILD-PROOF.

-with padlocks, master switches or by removing starter keys.

9. USE PROPER SPEED.

tool will do a better and safer job when operated at the

proper speed.

10. USE RIGHT T

OOL.

Don’t force the tool or the attachment to do a job for which it

was not designed.

11. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings,

watch) because they could get caught in moving parts. Non-

slip footwear is recommended. W

ear protective hair covering

to contain long hair

. Roll up long sleeves above the elbows.

12. ALWAYS WEAR SAFETY GLASSES.

lways wear safety glasses (ANSI Z87.1). Everyday

eyeglasses only have impact resistant lenses, thet are

NOT

safety glasses. Also use a face or dust mask if cutting

operation is dusty.

13. DON’T OVERREACH.

Keep proper footing and balance at all times.

14. MAINTAIN TOOL WITH CARE.

Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

15. DISCONNECT T

OOLS.

Before servicing, when changing accessories or attachments.

16. AVOID ACCIDENTAL STARTING.

Make sure the swich is in the ‘’OFF’’ position before plugging

in.

17. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the

instructions that accompany the accessories. The use of

improper accessories may cause hazards.

18. NEVER STAND ON TOOL.

Serious injury could occur if the tool tips over. Do not store

materials such that it is necessary to stand on the tool to reach

them.

19. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are

damaged should be carefully checked to ensure that they will

operate properly and perform their intended function. Check for

alignment of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation.

guard or

other parts that are da -maged should be properly repaired or

replaced.

20. NEVER LEAVE MACHINE RUNNING

UNATTENDED.

Turn power ‘’OFF’’. Don’t leave any tool running until it comes

to a complete stop.

ELECTRICAL INFORMATION

ARNING!

ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN

SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE TABLE SAW DISCONNECTED FROM THE

POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!

POWER SUPPLY

WARNING:

YOUR TABLE SAW MUST BE CONNECTED TO A 110V, 15-AMP. BRANCH CIRCUIT. FAILURE TO CONNECT IN THIS

WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.

WARNING: DO NOT USE A TWO-PRONG ADAPTOR FOR THEY ARE NOT IN ACCORDANCE WITH LOCAL CODES AND

ORDINANCES. NEVER USE IN CANADA.

DOUBLE INSULATION TOOLS

Double Insulation is a design concept used in electric power tools which eliminates the need for the three wire grounded power cord and

grounded power supply system. It is a recognized and approved system by Underwriter’s Laboratories, CSA and Federal OSHA

authorities.

IMPORTANT: Servicing of a tool with double insulation requires care and knowledge of the system and should be performed only by a

qualified service technician.

WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS OR THOSE RECOMMENDED BY THE MANUFACTURER.

RESET BUTTON

This table saw comes with a reset button (next to the power switch). When the table saw motor overheats, a safety mechanism stops the

motor automatically. Press the reset button and restart the table saw. If the table saw does not restart, wait 5 minutes before restarting.

POLARIZED PLUGS: Your tool is equipped with a polarized plug (one blade is wider than the other), this plug will fit in a polarized outlet

only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the

proper outlet. To reduce the risk of electric shock, do not change the plug in any way.

EXTENSION CORDS

WARNING:

Replace damaged cords immediately. Use of damaged cords can shock, burn or electrocute.

WARNING: Always use proper extension cord. If an extension cord is necessary, a cord with adequate size conductors should be used to

prevent excessive voltage drop, loss of power or overheating. The table shows the correct size to use, depending on cord length and

nameplate amperage rating of tool If in doubt, use the next heavier gauge. Always use U.L. and CSA listed extension cords.

FIGURE 1

Tool’s

Amperage

Rating

3-6

6-8

8-10

10-12

12-16

Cord Size in A.W.G.

Cord Length in Feet

25 50 100 150

18 16 16 14

18 16 14 12

14 12 - -

ire Sizes in mm

Cord Length in Meters

15 30 60 120

.75 .75 1.5 2.5

.75 1.0 2.5 4.0

1.0 2.5 4.0 -

----

GETTING TO KNOW YOUR TABLE SAW

1. POWER SWITCH

2. TABLE

Provides large working surface to support workpiece.

3. BASE

Supports table saw. For additional stability, holes are provided in

the base to bolt the saw to a workbench or stand.

4. BLADE TIL

T LOCK HANDLE

Locks the tilt mechanism after the blade is adjusted to desired

position.

5. RESET BUTTON

6. WRENCH ST

ORAGE

Conveniently stores wrenches when not in use.

7. ELEVATION WHEEL

Elevates or lowers the blade. Also used to tilt the blade 0

to 45

8. BLADE TIL

T SCALE

Shows the degree the blade is tilted.

9. RIP FENCE POINTER

Shows the distance from the blade to the rip fence through a

convenient viewing window.

10. MITER GAUGE SCALE

Shows the degree the workpiece is being mitered.

11. RIP FENCE STORAGE

Conveniently stores rip fence when not in use.

12. MITER GAUGE STORAGE

Conveniently stores miter gauge when not in use.

13. RIP FENCE

Rip fence can be easily moved or locked in place by simply

raising or lowering lock-handle.

14. BLADE GUARD

Protects the operator, and must always be in place and working

properly for all thru-sawing cuts. That is all cuts whereby the

blade cuts completely through the workpiece.

15. TABLE INSERT

Is removable for removing or installing blade or other cutting

tools.

16. MITER GAUGE

Head can be locked in desired position for crosscutting or

mitering by tightening the lock knob. ALWAYS SECURELY LOCK

IT WHEN IN USE.

FIGURE 2

7. ELEVATION WHEEL

9. RIP FENCE POINTER

0. MITER GAUGE SCALE

11. RIP FENCE STORAGE

12. MITER GAUGE STORAGE

(SIDE)

13. RIP FENCE

14. BLADE GUARD

15. TABLE INSERT

16. MITER GAUGE

4. BLADE TILT LOCK HANDLE

3. BASE

. TABLE

1. POWER SWITCH

5. RESET BUTTON

6. WRENCH STORAGE

8. BLADE TILT SCALE

ASSEMBLY & ADJUSTMENTS

OUNTING TABLE SAW TO WORKBENCH

f table saw is to be used in a permanent location, it should be fastened

securely to a firm supporting surface such as a workbench, using the four

mounting holes supplied in the base.

1. If mounting to a workbench, the base should be bolted securely through

ounting holes provided.

2. Locate and mark where the saw is to be mounted.

3. Drill four (4) 3/8˝ diameter holes through workbench.

4. Place table saw on workbench aligning holes in base with the holes

drilled in workbench.

5. Insert four (4) 5/16˝ dia. bolts through holes in base and supporting

surface then secure with (4) 5/16˝ hex nuts.

An opening MUST be made the same size as the opening under the table

saw base using the dimensions shown in Fig.3. This opening prevents dust

accumulation inside the table saw base.

Stand model SS-5007 with adaptable dust collection bag model KW-5007

are available as optional accessories if workbench mounting is not

desired.

MOUNTING HANDLE TO HANDWHEEL

The handle assembly found in the loose parts bag must be assembled to

the height raising handwheel.

MOUNTING BLADE GUARD ASSEMBLY

Position the recessed end of the spreader support (A) Fig.4 against the end

of the pivot rod and fasten it to the table using long hex. bolt, washer and

lock washer (B). Assemble spreader support bracket (C) to spreader

support (A) using hex. bolts and lock washers (D). Slide blade guard

splitter into spreader support bracket and fix in place using wing nut and

hex. bolt. Further adjustments will be necessary, keep hex. bolts loose at

this time.

IMPORT

ANT:

The blade guard splitter must be properly aligned with the

center of the blade (aligned with blade kerf). Using a straight edge, check

if the splitter is aligned with the blade. Adjust if necessary. Once properly

adjusted, tighten all support hex. bolts in Fig.4.

MOUNTING RIP

FENCE ON T

ABLE & ADJUSTMENTS

Mount rip fence handle to the front cam of the rip fence. Loosen rear clamp

screw (A) Fig.5 2-3 turns counterclockwise then place rip fence on table

making sure front end is properly fitted in the front rail. Lock rip fence into

place by lowering rip fence lock handle (B). Tighten rear clamp screw 2-3

turns clockwise to bring rear clamp closer to the rear rail until a good fit is

obtained.

To reduce the risks of kickback, the rip fence must be perfectly parallel to

the blade. Unlock rip fence by raising lock handle (B). Loosen both hex.

bolts (C) on top of the rip fence. Align the rip fence with the blade and

retighten both hex. bolts (C).

Adjust the pointer to the same marking by

loosening pointer screw (D) and repositioning pointer.

FIGURE 3

FIGURE 4

FIGURE 5

ASSEMBLY & ADJUSTMENTS

OUNTING AND ADJUSTING MITER GAUGE

When cross cutting and the blade is set at 90

and 45

to the table, the miter

gauge can be used in either slot on the table. When cross cutting and the

blade is tilted, use slot on right side of table where the blade is tilted away

from your hands and miter gauge.

1. To adjust the miter gauge, loosen lock knob (A) and set the miter gauge body

(B) so the pointer (C) is at desired angle, then tighten lock knob (A) Fig.6.

2. Make a cut on a piece of scrap wood. Check it with a square to see if the

piece of wood was cut at 90º. If the piece of wood was not cut at 90º,

adjust the miter gauge body, tighten lock knob and make additional cuts

until you are certain you have made a 90º cut. If pointer (C) is not point-

ing to 90º, loosen screw (D) adjust pointer and tighten screw.

CHANGING BLADE

Warning! Disconnect power cord from power source before changing

blade.

1. Remove table insert screws and insert (A) Fig.7 to gain access to the

blade arbor.

2. Turn handwheel clockwise until the blade is at its highest.

3. Place open end wrench (B) on the flat portion of the inside blade flange

to prevent the saw arbor from rotating. Turn the arbor nut (C) counter-

clockwise with the closed wrench (D) and remove arbor nut and outside

blade flange (E).

4. Place new blade on arbor making sure the blade teeth point downwards

towards the front of the table.

5. Replace outside blade flange and arbor nut and tighten with arbor

wrenches.

6. Lower blade under table and reinstall the table insert using screws

removed previously.

BLADE TILT

The table saw blade can be tilted to any degree between 0º and 45º to the

left. The blade angle lock knob (A) Fig.8 locks the tilting mechanism.

Loosen blade angle lock knob and slide the handwheel (B) until the blade

is positioned at the desired angle. Retighten angle lock knob.

ADJUSTING BLADE TILT 90º AND 45º POSITIVE STOPS

Warning! Disconnect power cord from power source before making the

following adjustments.

Adjusting 90º positive stop

1. Loosen blade angle lock knob (A)

Fig.8, slide handwheel (B) to the left

as far as possible and retighten blade angle lock knob.

2. Place a combination square on the table as shown Fig.9 and check if

blade is at a 90º to the table. If an adjustment is necessary

, loosen blade

angle lock knob and turn 90º adjustement screw (A) Fig.9 a few turns and

move the handwheel until the blade is 90º to the table. Tighten blade

angle lock and turn the 90º adjustment screw (A) until it is set at 90º.

Adjusting 45º positive stop

1. Loosen blade angle lock knob (A) Fig.8, slide handwheel (B) to the

right as far as possible and retighten blade angle lock knob.

2. Place a combination square on the table as shown Fig.9. and check if

blade is at a 45º to the table. If an adjustment is necessary

, loosen blade

angle lock knob and turn 45º adjustement screw (B) Fig.9 a few turns and

move the handwheel until the blade is 45º to the table. Tighten blade

angle lock and turn the 45º adjustment screw (B) until it is set at 45º.

FIGURE 6

FIGURE 7

FIGURE 8

FIGURE 9

AINTENENCE

WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before maintaining or lubricating your saw.

Do not allow sawdust to accumulate inside the saw. Frequently blow out any dust that may accumulate inside the saw cabinet and the motor.

Clean your cutting tools with a Gum and Pitch Remover. The cord and tool should be wiped with a dry clean cloth to prevent deterioration

rom oil and grease.

ARNING:

ertain cleaning agents and solvents can damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated

cleaning solvents, ammonia and household detergents which contain ammonia. Avoiding use of these and other types off cleaning agents

will minimize the possibility of damage.

A coat of automobile type wax applied to the table will help to keep the surface clean and allow workpieces to slide more freely.

If the power cord is worn or cut, or damaged in any way, have it replaced immediately.

Make sure the teeth of the

ANTIKICKBACK pawls are always sharp. To sharpen:

1. Remove blade guard.

2. Rotate pawl toward rear of spreader so that teeth are above top of spreader.

3. Hold spreader with left hand and place pawl over corner of workbench.

4. Using a small round file (Smooth Cut) sharpen the teeth.

WARNING: All repairs, electrical or mechanical, should be attempted only by trained repairmen. Contact the nearest King Canada Service

Center. Use only identical replacement parts, any other may create a hazard.

LUBRICATION

The gear case has been completely lubricated at the factory. However, after six months to one year, depending on use, it is wise to return

your tool to the nearest Service Center for the following:

• Brushes replaced

• Parts cleaned and inspected

• Relubricated with fresh lubricant

• Electrical system tested

• All repairs

The following parts should be oiled occasionally with SAE No. 20 or No. 30 oil, or WD 40.

1. Elevation, support rods, and gears.

2. Sliding rails and supports.

3. Table locking cams (Front & Rear).

MAINTENANCE

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

King Canada KC-5007 User manual

Brand: King Canada

Model: KC-5007

Category: Power tools

Type: User manual

Download PDF

report

King Canada KC-5007 User manual

King Canada KC-5007 User manual

Related papers

Other documents