Philips 150S6 User manual

e-Manual

Philips LCD Monitor Electronic User’s Manual

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/INDEX.HTM2005-04-06 3:13:07 PM

Safety and Troubleshooting Information

• Safety

Precautions

and

Maintenance

• FAQs

• Troubleshooting

• Regulatory

Information

• Other Related

Information

Safety and Troubleshooting Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than

those specified in this documentation may result in exposure to shock,

electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

Operation:

● Keep the monitor out of direct sunlight and away from stoves or any other heat source.

● Remove any object that could fall into ventilation holes or prevent proper cooling of the

monitor’s electronics.

● Do not block the ventilation holes on the cabinet.

● When positioning the monitor, make sure the power plug and outlet are easily accessible.

● If turning off the monitor by detaching the power cable or DC power cord, wait for 6

seconds before attaching the power cable or DC power cord for normal operation.

● Please use approved power cord provided by Philips all the time. If your power cord is

missing, please contact with your local service center. (Please refer to Customer Care

Consumer Information Center)

● Do not subject the LCD monitor to severe vibration or high impact conditions during

operation.

● Do not knock or drop the monitor during operation or transportation.

Maintenance:

● To protect your display from possible damage, do not put excessive pressure on the LCD

panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by

placing your hand or fingers on the LCD panel.

● Unplug the monitor if you are not going to use it for an extensive period of time.

● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be

wiped with a dry cloth when the power is off. However, never use organic solvent, such

as, alcohol, or ammonia-based liquids to clean your monitor.

● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to

dust, rain, water, or excessive moisture environment.

● If your monitor gets wet, wipe it with dry cloth as soon as possible.

● If foreign substance or water gets in your monitor, please turn the power off immediately

and disconnect the power cord. Then, remove the foreign substance or water, and send

it to the maintenance center.

● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or

extreme cold.

● In order to maintain the best performance of your monitor and use it for a longer ligetime,

please use the monitor in a location that falls within the following temperature and

humidity ranges.

❍ Temperature: 5-40°C 41-104°F

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/safety/safety.htm (1 of 2)2005-04-06 3:13:15 PM

Safety and Troubleshooting Information

❍ Humidity: 20-80% RH

Service:

● The casing cover should be opened only by qualified service personnel.

● If there is any need for any document for repair or integration, please contact with your

local service center. (please refer to the chapter of "Consumer Information Center")

● For transportation information, please refer to "Physical Specifications".

● Do not leave your monitor in a car/trunk under direct sun light.

Consult a service technician if the monitor does not operate normally, or you are

not sure what procedure to take when the operating instructions given in this

manual have been followed.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/safety/safety.htm (2 of 2)2005-04-06 3:13:15 PM

About This Manual

• About This

Guide

• Notational

Descriptions

About This Manual

About This Guide

This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It

describes the LCD monitor's features, setup, operation and other important information. Its

contents are identical to the information in our printed version.

It includes the following sections:

● Safety and Troubleshooting Information provides tips and solutions for common problems

as well as other related information you may need.

● About This Electronic User's Manual gives an overview of information included, along with

notation icon descriptions and other documentation for your reference.

● Product Information gives an overview of the monitor's features as well as the technical

specifications for this monitor.

● Installing Your Monitor describes the initial setup process and gives an overview of how to

use the monitor.

● On-Screen Display provides information on adjusting the settings on your monitor.

● Customer Care and Warranty contains a list of worldwide Philips Consumer Information

Centers along with help desk phone numbers and information on the warranty applicable

to your product.

● Glossary defines technical terms.

● Download and Print Option transfers this entire manual to your hard drive for easy

reference.

RETURN TO TOP OF THE PAGE

Notational Descriptions

The following subsections describe notational conventions used in this document.

Notes, Cautions and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic

type. These blocks contain notes, cautions or warnings. They are used as follows:

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/about/about.htm (1 of 2)2005-04-06 3:13:17 PM

About This Manual

NOTE: This icon indicates important information and tips that help you make

better use of your computer system.

CAUTION: This icon indicates information that tells you how to avoid either

potential damage to hardware or loss of data.

WARNING: This icon indicates the potential for bodily harm and tells you how

to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In

such cases, the specific presentation of the warning is mandated by the relevant regulatory

authority.

RETURN TO TOP OF THE PAGE

broadcasting in whole or in part is prohibited without written consent of Philips Electronics NV

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/about/about.htm (2 of 2)2005-04-06 3:13:17 PM

Product Information
 
     
 
• SmartManage
• Product 
Features
• Lead-free 
Product
• Technical 
Specifications
• Resolution & 
Preset Modes
• Philips Pixel 
Defect Policy
• Automatic 
Power Saving
• Physical 
Specification
• Pin 
Assignment
• Product 
Views
• Physical 
Function
Product Information 
Product Features
150S6
● Best Total Cost of Ownership solution 
❍ SmartManage provides remote management capabilities
❍ Lead-free display protects your health and our environment
❍ Power consumption below the industry average
❍ TCO guarantees the highest safety and ergonomics standards
❍ Environmentally responsible Energy Star partner
❍ Kensington anti-theft lock secures monitor against theft
● Outstanding front of screen performance 
❍ Fast response time capable of handling fast moving pictures
❍ XGA 1024x768 resolution for sharper display
❍ sRGB ensures color matching between display and printouts
● Great Convenience 
❍ Embedded power supply eliminates external power adaptors
❍ Plug and play for easy and friendly installation
❍ FlexiHolder to hold notes, cards, and photos
RETURN TO TOP OF THE PAGE
 
Lead-free Product 
Philips eliminated toxic substances like lead from its displays. Lead-free display 
helps protect your health and promotes environmentally sound recovery and 
disposal of waste from electrical and electronic equipment.Philips complies with the 
European Community stringent RoHS Directive mandating restrictions on hazardous 
substances in electrical and electronic equipment. With Philips, you can be confident 
that your display device does not harm the environment.
Technical Specifications* 
LCD PANEL 
• Type TFT LCD
• Screen size 15" visual
file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (1 of 7)2005-04-06 3:13:20 PM

Product Information

• Pixel Pitch 0.297 x 0.297 mm

• LCD Panel type

1024 x 768 pixels

R.G.B. vertical stripe

Anti-glare polarizer, hard coated

• Effective viewing area 304.1 x 228.1 mm

• Display Colors 16.2M colors

SCANNING

Vertical refresh rate 56 Hz-76 Hz

Horizontal Frequency 30 kHz-63 kHz

VIDEO

• Video dot rate 80 MHz

• Input impedance

- Video

75 ohm

- Sync

2K ohm

• Input signal levels 700m Vpp

• Sync input signal

Separate sync

Composite sync

Sync on green

• Sync polarities Positive and negative

• Input Frequency

XGA Hsync 48- 61 kHz, Vsync 60 - 76 Hz (N.I.)

SVGA Hsync 35- 50 kHz, Vsync 56 - 75 Hz (N.I.)

VGA Hsync 31- 38 kHz, Vsync 60 - 76 Hz (N.I.)

• Video interface Analog (D-Sub)

Optical characteristics

• Contrast ratio 450:1 (typ.)

• Brightness

250 cd/m

2

(typ.)

• Peak contrast angle 6 o'clock

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (2 of 7)2005-04-06 3:13:20 PM

Product Information

• White Chromaticity

x: 0.283 y: 0.297 (at 9300°K)

x: 0.313 y: 0.329 (at 6500°K)

x: 0.313 y: 0.329 (at sRGB)

• Viewing Angle (C/R>5)

Upper > 60° (typ.)

Lower > 80° (typ.)

Left > 80° (typ.)

Right > 80° (typ.)

• Response time

<16 ms (typ.)

* This data is subject to change without notice.

RETURN TO TOP OF THE PAGE

Resolution & Preset Modes

• Maximum

1024 x 768 at 75 Hz

•

Recommended

1024 x 768 at 60 Hz

50 user definable modes

14 factory preset modes:

H. freq (kHz) Resolution V. freq (Hz)

31.469 640*350 70.086

31.469 720*400 70.087

31.469 640*480 59.940

35.000 640*480 67.000

37.861 640*480 72.809

37.500 640*480 75.000

35.156 800*600 56.250

37.879 800*600 60.317

48.077 800*600 72.188

46.875 800*600 75.000

49.700 832*624 75.000

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (3 of 7)2005-04-06 3:13:20 PM

Product Information

48.363 1024*768 60.004

56.476 1024*768 70.069

60.023 1024*768 75.029

RETURN TO TOP OF THE PAGE

Automatic Power Saving

If you have VESA DPMS compliance display card or software installed in your PC, the monitor can

automatically reduce its power consumption when not in use. If an input from a keyboard, mouse

or other input device is detected, the monitor will 'wake up' automatically. The following table

shows the power consumption and signaling of this automatic power saving feature:

Power Management Definition

VESA Mode Video H-sync V-sync Power Used LED color

Active ON Yes Yes < 17 W (typ.) Green

Sleep OFF No No < 1 W Amber

Switch Off OFF - - < 1W Off

This monitor is

ENERGY STAR

®

compliant. As an ENERGY STAR

®

Partner, PHILIPS has

determined that this product meets the

ENERGY STAR

®

guidelines for energy efficiency.

RETURN TO TOP OF THE PAGE

Physical Specifications

• Dimension (WxHxD) *

342 x 344 x 180 mm (incl. Pedestal)

• Weight 2.7 Kg

• Tilt -5° ~ 25°

• Power supply 100 — 240 VAC, 60 - 50 Hz

• Power consumption 17 W* (typ.)

• Temperature

5° C to 40° C (operating)

-20° C to 60° C (storage)

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (4 of 7)2005-04-06 3:13:20 PM

Product Information

• Relative humidity 20% to 80%

• System MTBF 50K hours (CCFL 40K hours)

• Cabinet color

150S6FG: Light Gray

150S6FB: Black

150S6FS: Silver

* This data is subject to change without notice.

* Resolution 1024x768, standard size, brightness max., contrast 50%, full white pattern, without

audio/USB.

RETURN TO TOP OF THE PAGE

Pin Assignment

The 15-pin D-sub connector (male) of the signal cable:

No.

Assignment

No.

Assignment

1

Red video input

9

DDC + 3.3 V

2

Green video input/SOG

10

Logic ground

3

Blue video input

11

Ground

4

Ground

12

Serial data line (SDA)

5

Cable detect

13

H. Sync / H+V

6

Red video ground

14

V. Sync

7

Green video ground

15

Data clock line (SCL)

8

Blue video ground

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (5 of 7)2005-04-06 3:13:20 PM

Product Information

RETURN TO TOP OF THE PAGE

Product Views

Follow the links to see various views of the monitor and its components.

Front View Product Description

RETURN TO TOP OF THE PAGE

Physical Function

1) Tilt

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (6 of 7)2005-04-06 3:13:20 PM

Product Information

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/product/product.htm (7 of 7)2005-04-06 3:13:20 PM

Installing Your LCD Monitor

•

Front View

Produt

Description

•

Connecting

to Your PC

• The Base

•

Getting

Started

•

Optimizing

Performance

Installing Your LCD Monitor

Front View Product Description

UP and DOWN buttons are used when adjusting the OSD of your

monitor.

LEFT and RIGHT buttons, like the UP and DOWN buttons, are also

used in adjusting the OSD of your monitor.

BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are

pressed, the adjustment controls for the BRIGHTNESS will show up.

OK button which when pressed will take you to the OSD controls.

POWER button switches your monitor on.

Automatically adjust the horizontal position, vertical position, phase

and clock setting.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/install/install.htm (1 of 3)2005-04-06 3:13:23 PM

Installing Your LCD Monitor

Rear View

1 Kensington anti-thief lock

2 VGA input

3 AC power input

RETURN TO TOP OF THE PAGE

Optimizing Performance

● For best performance, ensure that your display settings are set at 1024x768, 60Hz.

Note: You can check the current display settings by pressing the 'OK' button

once. The current display mode is shown in OSD main controls called

RESOLUTION.

● You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best

performance out of your monitor. This is included on this CD. Step-by-step instructions are

provided to guide you through the installtion process. Click on the link to know more about

this program.

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/install/install.htm (2 of 3)2005-04-06 3:13:23 PM

Installing Your LCD Monitor

More about FP_setup04.exe

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/install/install.htm (3 of 3)2005-04-06 3:13:23 PM

On-Screen Display

• Description

of the On-

Screen

Display

•

The OSD

Tree

On-Screen Display

Description of the On Screen Display

What is the On-Screen Display?

On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust

screen performance or select functions of the monitors directly through an on-screen instruction

window. A user friendly on screen display interface is shown as below :

Basic and simple instruction on the control keys.

In the OSD shown above users can press

buttons at the front bezel of the monitor to move

the cursor, to confirm the choice or change, and to adjust/select the change.

RETURN TO TOP OF THE PAGE

The OSD Tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference

when you want to work your way around the different adjustments later on.

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/osd/osddesc.htm (1 of 3)2005-04-06 3:13:25 PM

On-Screen Display

Note: sRGB is a standard for ensuring correct exchange of colors between different devices (e.g.

digital cameras, monitors, printers, scanners, etc.)

Using a standard unified color space, sRGB will help represent pictures taken by an sRGB

compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are

calibrated and you can rely on the correctness of the colors shown on your screen.

Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a

predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/osd/osddesc.htm (2 of 3)2005-04-06 3:13:25 PM

On-Screen Display

the monitor's OSD.

To do so, open the OSD by pressing the OK button on the front of your monitor. Move the down

button to go to Color and press OK again. Use the right button to go to sRGB. Then move the down

button and press OK again to exit the OSD.

After this, please do not change the brightness or contrast setting of your monitor. If you change

either of these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K.

RETURN TO TOP OF THE PAGE

file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/osd/osddesc.htm (3 of 3)2005-04-06 3:13:25 PM

Customer Care & Warranty
 
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR 
WARRANTY COVERAGE
WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • 
Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • 
Switzerland • Spain • United Kingdom 
EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • 
Turkey
LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • 
Peru • Uruguay • Venezuela
NORTH AMERICA: Canada • USA
PACIFIC: Australia • New Zealand
ASIA: Bangladesh • China • Hong Kong • India • Indonesia • Japan • Korea • Malaysia • 
Pakistan • Philippines • Singapore • Taiwan • Thailand
AFRICA: Morocco • South Africa
MIDDLE EAST: Dubai • Egypt
  
file:///D|/My%20Documents/dfu/A5_new/ENGLISH/warranty/warranty.htm2005-04-06 3:13:28 PM

Glossary
 
     
 
 
 
 
 
 
 
Glossary
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 
A
Active matrix
This is a kind of liquid crystal display structure in which switching transistors are attached to each 
pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing 
angle than a passive matrix display. Also refer to TFT (thin film transistor).
Amorphous silicon (a-Si)
A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active 
matrix LCD.
Aspect ratio
The width-to-height ratio of the active area of a display. In general, most monitors have an aspect 
ratio of 4:3. Wide monitors or TVs have an aspect ratio of 16:9 or 16:10.
RETURN TO TOP OF THE PAGE
 
B
Backlight
The light source for a transmissive LCD. There are two techniques used in nowaday LCD designs. 
Most TFT LCD panels use CCFLs (cold cathode fluorescent light) and a diffuser panel directly 
behind the liquid crystal layer. New technology using Light Emitting Drodes (LED) are still under 
development.
Brightness
file:///D|/My%20Documents/dfu/A5_new/ENGLISH/150S6/glossary/glossary.htm (1 of 10)2005-04-06 3:13:31 PM

Page is loading ...

Philips 150S6 User manual

This manual is also suitable for

Philips 150S6 User manual

Related papers

Other documents