Baby Trend Canadian Ally 35 Infant Seat Owner's manual

Category
Car seat
Type
Owner's manual

This manual is also suitable for

1-800-328-7363
(8:00am ~ 4:30pm PST)
www.babytrend.com
Baby Trend, Inc.
13048 Valley Blvd.
Fontana CA 92335
If you experience any difculty in using this product, please
contact our customer service department at 1-800-328-
7363 between the hours of 8:00am and 4:30pm Pacic
Standard Time for assistance. Please have your model
number and manufacturing date available when you call.
This information can be found on a small sticker on the
bottom of the product.
STOP
Copyright © 2020, Baby Trend, Inc.
Carefully read and understand all instructions and
warnings in this manual. Failure to properly use
this Infant Car Seat increases the risk of SERIOUS
INJURY or DEATH in a sudden stop or crash.
KEEP INSTRUCTIONS FOR FUTURE USE.
Store this manual in the pocket provided on
the side of the seat.
WARNING
ALLY
-
35
INFANT CAR SEAT
OWNER’S MANUAL
Child Weight: 1.8 to 15.8 kg (4 to 35 lbs)
Child Height: 81.3 cm or less (32”)
ALLY_35_041520_CAN_E
Store this manual in
the pocket provided
underneath the
Car Seat Cover.
Copyright © 2017, Baby Trend, Inc.
Carefully read and understand all instructions and
warnings in this manual. Failure to properly use
this Infant Car Seat incre ases the risk of SERIOUS
INJURY or DEATH in a sudden stop or crash.
KEEP INSTRUCTIONS FOR FUTURE USE.
Store this manual in the pocket provided on
the side of the seat.
WARNING
ALLIE-35
®
INFANT CAR SEAT
OWNER’S MANUAL
Child Weight: 4 to 35 lbs (1.82 to 15.8 kg)
Child Height: 32” or less (81.3 cm)
ALLIE_35_101917U
www.babytrend.com
1 2
TABLE OF CONTENTS TABLE OF CONTENTS
WARNINGS TO ALERT YOU TO POSSIBLE DANGERS ............................................. 3
HOW TO REGISTER YOUR SAFETY SEAT ................................................................. 4
SAFETY INFORMATION ................................................................................................ 5
3.1 About your child ................................................................................................ 5
3.2 About your vehicle ............................................................................................. 6
3.3 About Active Air Bags ........................................................................................ 7
3.4 About an unoccupied Safety Seat ..................................................................... 7
3.5 About this Safety Seat ....................................................................................... 8
3.6 About use as a carrier ....................................................................................... 9
SELECTING THE BEST LOCATION FOR THE SAFETY SEAT ................................. 11
4.1 Overall Considerations in Selecting a Location ................................................11
4.2 Check that the Vehicle Seat Meets the Following Requirements .................... 12
4.3 Check that the Vehicle Seat Belt is Safe to Use ............................................. 13
SAFETY SEAT FEATURES AND THEIR PROPER USE ............................................. 19
5.1 5-Point Harness .............................................................................................. 19
5.2 Rear View of Model ......................................................................................... 20
5.3 Base ................................................................................................................ 21
5.4 Use of the Safety Seat with the Base .............................................................. 23
5.5 Other Features ................................................................................................ 25
5.6 Operation of the Carry Handle ........................................................................ 27
5.7 Attaching the Canopy ...................................................................................... 28
5.8 Adjustment of the Shoulder Straps .................................................................. 29
Low Birth Weight Adjustment .................................................................................... 32
5.9 Low Birth Weight Use ...................................................................................... 32
USING INFANT RESTRAINT ....................................................................................... 35
6.1 Securing your Child in the Safety Seat / Carrier ............................................. 35
6.2 For the 5-Point Harness .................................................................................. 38
SECURING THE SAFETY SEAT OR BASE IN THE VEHICLE ................................... 39
7.1 Preparation ...................................................................................................... 40
7.2 Installation of the Safety Seat / Vehicle Belt Installation of Base .................... 41
7.3 Secure Base WITH Vehicle Combination Lap/Shoulder Belt .......................... 42
7.4 Secure Base WITH Vehicle Lap Belt only ...................................................... 42
7.5 Tightening Vehicle Seat Belt ........................................................................... 42
7.6 To Remove Base ............................................................................................. 43
7.7 Attach Car Seat to Base .................................................................................. 44
7.8 Removing Car Seat from Base ....................................................................... 45
7.9 Car Seat Only Installation without Base .......................................................... 46
7.9.1 Initial Positioning .......................................................................................... 46
7.9.2 Securing Car Seat WITH Vehicle ................................................................. 48
7.9.3 Securing Car Seat WITH Vehicle Lap Belt only ........................................... 48
7.9.4 Tightening Vehicle Seat Belt ........................................................................ 48
7.9.5 To Remove Car Seat .................................................................................... 50
7.9.6 Installation of the Base using UAS ............................................................... 52
7.9.7 Setting Proper Recline of the Safety Seat / Base ........................................ 56
FINAL SAFETY CHECKS ............................................................................................. 61
ADDITIONAL INFORMATION ...................................................................................... 62
9.1 Using the Safety Seat in an Airplane ............................................................... 62
9.2 Using your Baby Trend Safety Seat with a Baby Trend Stroller ...................... 62
9.3 Cleaning and Maintenance ............................................................................. 62
9.4 Replacement Parts .......................................................................................... 64
9.5 Using the Cold Weather Boot .......................................................................... 65
9.6 Body Support Use ........................................................................................... 65
9.7 Aircraft Installation ........................................................................................... 66
9.8 Warranty ......................................................................................................... 66
4
2.0 Registration
3
1.0 Warnings
WARNINGS TO ALERT YOU TO
POSSIBLE DANGERS
The ultimate safety of your child depends on the proper
installation of the Safety Seat in your vehicle. Proper installation
requires that you read and understand this entire manual and
your vehicle’s owner’s manual before placing your child in the
Safety Seat. DO NOT allow others to install or use this safety
seat unless they completely understand it’s proper use and
installation.
Improper use of this Safety Seat can result in death or serious
injury from a crash, sharp turn or sudden stop.
Your child’s safety depends on:
1. Choosing the best location within your vehicle for the Safety
Seat. Seating positions with Active Air Bags must be avoided.
2. Adjust the harness shoulder strap locations to the appropriate
height for your child.
3. Adjust the harness length to be snug around your child.
4. This Safety Seat is only to be used in the rear-facing position.
5. Proper use and routing of the seat belts in your vehicle is
essential for proper installation. Not all vehicle seat belts will
adequately secure the Safety Seat.
6. Proper recline angle of the Safety Seat is required for maximum
protection of your child.
HOW TO REGISTER YOUR SAFETY
SEAT
Please complete the following information regarding this Safety
Seat:
Model Number : _________________
Manufactured in : _________________
Purchase Date : _________________
The model number can be found on a label on the side of the
Safety Seat. The manufactured date can be found on a label on
the bottom of the seat.
Please ll out the prepaid registration post card attached to the
safety harness and mail it today. In addition, we may nd a need
to update this instruction manual from time to time.
Child restraints could be recalled for safety reasons. You must
register this restraint to be reached in a recall. Send your name,
address, email address if available, and the restraint’s model
number and manufacturing date to Baby Trend, Inc, 13048
Valley Blvd. Fontana CA 92335 or call 1-800-328-7363 or
register online at http://www.babytrend.com/registration.html. For
recall information, call Transport Canada at 1-800-333-0371
(toll free), 613-998-8616 (Ottawa area) or go to
http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-
notices-menu-907.htm.
5
6
3.0 Safety 3.0 Safety
3.2 About your vehicle
• Proper installation of the Safety Seat in your vehicle and proper
securing of your child in the Safety Seat are essential to ensure
the safety of your child. Quick turns, sudden stops, or other
maneuvers in avoiding a crash, as well as a crash, can injure
your child if not properly secured in the seat or if the seat is not
properly installed in the vehicle.
• There are many different types of vehicles, seat belt systems,
or other occupant restraint systems in use today. Accordingly,
this manual can only give guidelines for proper installation in
your vehicle. In addition to this manual, you must also read
and understand the vehicle owners manual, which should
address use of child restraints. If your vehicle owner’s manual
does not address the installation of child restraints, please
contact your local vehicle dealer, or the vehicle’s manufacturer,
to obtain this information before using this Safety Seat.
• Some vehicles do not have any safe location for this Safety
Seat to be installed. In addition, many vehicles do not have
seat belt systems that will adequately hold this Safety
Seat in the required position. Please refer to both this manual
and your vehicle owner’s manual for complete information for
proper safe installation of this Safety Seat.
Never combine this Safety Seat or Base with any other Safety
Seat or Base from any other manufacturer. If you are in need
of an additional Base, please contact your local dealer or Baby
Trend, Inc. to obtain one.
• This Car Seat is certied for use in Motor Vehicles and Aircraft
and conforms to all applicable Canadian Motor Vehicle Safety
standards (213 and 213.1).
SAFETY INFORMATION
3.1 About your child
This Safety Seat is designed and tested to accommodate a
child of a specic range of HEIGHT and WEIGHT. Using the
Safety Seat for a child whose weight or height is outside of
these limits will increase the risk of death or serious injury
in the event of a crash. Please see the Warning label on
the Safety Seat located on the child’s right side for weight
and height limits for your model. Also noted on manual
cover.
• Special needs children, such as pre-term babies, may suffer
difculties in using this Safety Seat. The angle of recline in this
Safety Seat may not be appropriate for Special Needs babies.
If your child has special needs or any breathing difculties,
please discuss vehicle Safety Seats with your pediatrician, or
other competent health care provider, to ensure the safety of
your child.
• Use only car seat accessories manufactured by Baby Trend.
Accessories can affect your child’s safety in a sudden stop or
crash.
• DO NOT modify or attach any toys, padding, or other items
to this Safety Seat. Untested modications or padding could
result in injury in a crash.
• Do Not Dress your child in bulky clothing or other garments that
will hinder the harness from being snug around your child and
properly latched between your child’s legs.
7
8
3.0 Safety 3.0 Safety
3.5 About this Safety Seat
• This Safety Seat is constructed of plastic that can deform over
time if left with any object in the seat while stored. DO NOT
leave heavy objects in the seat while not in use. DO NOT store
the seat in the trunk of your car with heavy objects on it or with
pressure on the seat from the trunk lid.
Replace the Safety Seat and Base after an accident of
any kind. An accident, even a minor accident, can cause
undetectable damage to the Safety Seat or Base that may
cause the Seat or Base to fail in a subsequent accident. DO
NOT use the safety seat if it is damaged or broken.
• Discontinue use of the Safety Seat and Base after six (6) years
from the date of manufacture. The date of manufacture can
be found on the label located on the underside of the Safety
Seat or Base. When discarding an out of date seat, please
ensure that someone nding the seat will be unable to use it.
We suggest that you disable the seat by removing the pad and
harness and discarding the pieces at different times.
3.3 About Active Air Bags
NEVER PLACE THIS SAFETY SEAT IN A VEHICLE SEATING
LOCATION THAT HAS AN ACTIVE AIR BAG. If an Active
Air bag inates, it can hit the safety seat with great force and
cause death or serious injury to your child. Refer to your vehicle
owner’s manual for additional information and warnings about
Active Air bags, and supplemental restraints, and their proper use
with Safety Seats.
3.4 About an unoccupied Safety Seat
Never leave the Safety Seat or Base unsecured in your
vehicle. An unsecured seat or base can y through the vehicle
in the event of a crash, sudden stop or sharp turn and cause
serious injury to the driver, who may then loose control of the
vehicle, or to passengers. When not in use, either remove the
seat and or base from the vehicle or make sure that both are
securely belted to the vehicle according to these instructions.
• The Safety Seat may become very hot if left in direct sunlight.
Your child may suffer burns from hot plastic components.
Always check the seat for hot surfaces that may come into
contact with your child before placing your child in the seat.
We suggest that you cover the seat with a blanket or towel if
it will be subject to direct sunlight while you are away from the
vehicle.
9
10
3.0 Safety 3.0 Safety
- DO NOT place items with string around a child’s neck, such
as hood strings, pacier cords, etc.
- DO NOT suspend strings on or over carrier.
- DO NOT attach strings to toys.
- DO NOT place the carrier near a window where cords from
blinds or drapes can strangle a child.
3.6 About use as a carrier
Never Leave Your Child Unattended, even if they are asleep.
Very often when you arrive at your destination you will nd
that your child has fallen asleep in the Seat. Do not leave the
child unattended, even for a minute. Your child can tip or move
the carrier by their movements, kicking or grabbing on to their
surroundings. If the carrier tips over, your child can suffocate
from the surface that the seat is on as well as from the pressure
on their chest from the safety harness. In addition, if the carrier
is placed too upright, the child’s head can fall forward and cause
the child to have difculty breathing. To avoid death or serious
injury from suffocation, falls and other hazards:
Always place the carrier on a rm and level surface. Never place
the carrier on soft or plush surfaces such as a bed, comforter, couch,
sofa, chair, etc. The carrier has a very high possibility of tipping
over if placed on a soft or plush surface.
• Fall hazard: Child’s movements can slide carrier. Never place the
carrier near the edge of high surfaces such as tables, counter tops,
shelves, or other elevated surfaces. To prevent falls, stay within
arm’s reach whenever the carrier is not on the oor or ground.
• Child can strangle in loose safety harness straps. Never leave child
in carrier when straps are loose or undone. Always use the safety
harness as instructed in this manual when the child is in the carrier.
• Before lifting the carrier with the handle, check that the handle is
rmly locked into position. The carrier will pivot about an unlocked
handle and can result in injury to your child.
• Strings and cords can cause strangulation:
• Never leave child unattended.
SUFFOCATION HAZARD: Infant carrier can roll over on soft
surfaces and suffocate child, NEVER place carrier on beds,
sofas, or other soft surfaces.
STRANGULATION HAZARD:
- Child can strangle in loose restraint straps.
Never leave child in carrier when straps are
loose or undone.
- Children have STRANGLED in loose or
partially buckled harness straps. Fully
restrain the child even when carrier is used
outside the vehicle.
FALL HAZARD: Child’s activity can move
carrier. Never place carrier on counter tops,
tables, or other elevated surface. The carrier
can fall from the shopping cart. Do not use on
shopping cart.
WARNING
11
12
4.0 Location 4.0 Location
• If the driver is the only adult in the vehicle and the child
requires constant monitoring, then the forward seating position
may be used if there is no passenger side Active Air bag and
all of the following requirements are met for this location.
4.2 Check that the Vehicle Seat Meets the Following
Requirements
Never place this Safety Seat in a vehicle seating location
that has an Active Air Bag! Active Air Bags inate with great
force! An inating active Air Bag can strike a Safety Seat
with enough force to cause death or serious injury to your
child. If your vehicle is equipped with a front passenger side
Active Air bag, please refer to the vehicle’s owner’s manual for
additional information about Active Air bags and child safety
seat installation.
SELECTING THE BEST LOCATION FOR
THE SAFETY SEAT
Not every location within an automobile may be safe for the
installation of this Safety Seat. In fact, some automobiles have
no seating position that is safe for the installation of a safety
seat. Improper placement of this Safety Seat within a vehicle
will increase the risk of death or serious injury.
Please follow the instructions in this manual and in your
vehicle owner’s manual carefully to ensure proper location and
installation of this Safety Seat. If you are uncertain about the
proper location of the Safety Seat within the vehicle, contact
your vehicle manufacturer directly, or through their dealer
before using this seat. You are also invited to call Baby Trend
at1-800-328-7363 for additional information or assistance.
4.1 Overall Considerations in Selecting a Location
• The rear seating positions have been shown to be statistically
safer for children than the front seating position.
• We recommend that you use the center rear seat position as
the safest location for the Safety Seat. In addition, whenever
possible, have an adult ride in the rear with the child in order to
monitor the child.
DO NOT place rear-facing child
seat on front seat with air bag.
DEATH OR SERIOUS INJURY can
occur. The back seat is the safest
place for children 12 and under.
WARNING
WARNING
13
14
4.0 Location 4.0 Location
seat belts systems that are not safe for use with the Safety
Seat. These systems may look safe but their method of
operation precludes their use with the Safety Seat. If you are
unsure if the vehicle seat belt is safe for use with the Safety
Seat, please contact the vehicle manufacturer for additional
information.
Seat belt systems that are NOT safe for use with the Safety Seat:
DO NOT use the following types of seat belt systems with the
Safety Seat. These belt systems will not hold the Safety Seat
securely in place at all times. In addition, the locking clip provided
with this product will not make these belt systems safe to use.
Carefully analyze the operation of the vehicle safety belts
before using the Safety Seat. Being able to thread the vehicle
seat belt through the Safety Seat or Base is not an indication
that the vehicle seat belt is safe to use. Carefully read this
section on seat belt systems, review your vehicle owner’s
manual in detail, and heed any and all warning labels on your
vehicle’s seat belt. Your vehicle may require a modication
or special seat belt in order to be safely used with this Safety
Seat. Please see your vehicle dealer for this service.
DO NOT place this Safety Seat in any vehicle
seat that faces to the rear or to either side of
the vehicle (Fig. 13-1 & 13-2).
DO NOT use this Safety Seat in a vehicle
that has a vehicle seat back that does not
lock into place. A seat back that folds forward
must have a latch or locking mechanism to
prevent it from ying forward and striking the
child in a sudden stop or accident.
• Please review your vehicle owner’s manual
to determine the best location for the Safety
Seat or to determine if any locations are
unsafe for safety seat installation. If you
do not have the vehicle owner’s manual
or the owner’s manual does not address
child safety seat installation, please contact
the vehicle manufacturer to obtain this
information before using the safety seat.
4.3 Check that the Vehicle Seat Belt is Safe to Use
The Safety Seat is designed to be tightly installed at all
times. The vehicle seat belt must be capable of maintaining
tight installation at all times. A variety of vehicle seat belt
systems have been installed on vehicles that are not safe
for use with the Safety Seat. Even newer vehicles can have
Fig. 13-1
Fig. 13-2
WARNING
15
16
4.0 Location 4.0 Location
DO NOT use a seat belt that is anchored on
the seat more than 2 inches forward of the
crease between the seat bottom and the
seat back. This type of seat belt anchors
the Safety Seat too far forward and the
Safety Seat will not be safely restrained in
the vehicle (Fig. 16-1).
DO NOT use a shoulder belt that moves
along a track. These systems typically
move to surround the occupant when the
door is closed. This type of belt system will
NOT adequately restrain the Safety Seat.
(Fig. 16-2).
If you have any of the above seat belt
systems, DO NOT use it to secure the Safety
Seat in the vehicle. Look in the vehicle for a
location that has a more suitable seat belt
system as described in the section following.
You may also contact your vehicle’s
manufacturer to inquire about installing a
seat belt system that is adequate to restrain
a Safety Seat.
DO NOT use a lap belt that stays loose after
installed and locks only in a crash or sudden
stop. These lap belts utilize an Emergency
Locking Retractor and are often found in
combination with motorized shoulder belts.
Because these belts will allow the Safety
Seat to move about on the seat, the chance
of the Safety Seat being out of the proper
position in a crash is very high. Accordingly,
do not use the Safety Seat with this type of
Seat Belt system. Please see your vehicle’s
dealer or owner’s manual for information on
converting this seat belt system to one that
is acceptable for use with a Safety Seat
(Fig. 15-1).
DO NOT use a lap/shoulder belt system if
the lap belt and shoulder belt each have
retractors at one end. This type of seat
belt system will not adequately restrain the
Safety Seat (Fig. 15-2).
DO NOT use a seat belt that is connected
to the door in any way. These types of seat
belts are designed to automatically
surround the occupant when the door is
closed. This type of seat belt will NOT
adequately restrain the Safety Seat.
(Fig. 15-3).
Fig. 15-1
Fig. 15-2
Fig. 15-3
Fig. 16-1
Fig. 16-2
17
18
4.0 Location 4.0 Location
This combination seat belt does not require a
locking clip (Fig. 18-1).
A lap/shoulder combination belt system
with a latch plate that can slide freely along
the belt is suitable for use with the Safety
Seat if it includes a lockable retractor or if
a locking clip is used to secure the lap belt
into position and prevent loosening. Use the
locking clip provided with the Safety Seat as
instructed on page 43. Please refer to your
vehicle’s owners manual for additional
information on locking this style of seat
belt. This style of belt must be locked to
prevent movement of the Safety Seat
(Fig. 18-2 & 18-3).
Seat belt systems that are Adequate for use with the Safety
Seat:
The following seat belt systems can be used with the Safety Seat
provided, that all of the other requirements prescribed in these
instructions, including seat position, and all instructions provided
by your vehicle’s owner’s manual are followed.
A lap belt that is manually adjusted and will
remain tight while the vehicle is in motion is
suitable for use with the Safety Seat. Pulling
the belt through the buckle after the buckle is
fastened tightens this type of seat belt. The
center rear seat belt is most often this type of
seat belt (Fig. 17-1).
A lap belt that cannot be lengthened once
it is fastened is suitable for use with the
Safety Seat. These seat belts often have
an automatic locking retractor that will
allow the belt to be lengthened but once
fastened, must be unbuckled and allowed
to retract fully before allowing the belt to be
lengthened again (Fig. 17-2).
A lap/shoulder combination seat belt with a
latch plate that locks the lap belt into position
is suitable for use with the Safety Seat. Once
this type of seat belt is fastened, the latch
plate prevents the lap belt from loosening.
Fig. 17-1
Fig. 17-2
Fig. 18-1
Fig. 18-2
Fig. 18-3
19
20
5.0 Features 5.0 Features
SAFETY SEAT FEATURES AND THEIR
PROPER USE
5.1 5-Point Harness
Carry Handle
Canopy
Handle
Release
Button
Harness Clip
Vehicle Belt
Path/Hook
without base
Harness
Adjuster Strap
Harness
Straps
Seat Pad
Moving Seat
Back (Adjustable
Back Model)
Buckle
Harness
Adjuster Button
5.2 Rear view of Model
Harness Slots
Canopy
Seat Angle
Indicator
Harness
Belt
Owner’s
Manual
Holder
Modular
Adaptor
(if eqquipped)
Belt Adjuster
Plate
Base/Stroller
Hook
Locking Clip
Harness
Adjuster Strap
Shortening
Clip Storage
21
22
5.0 Features 5.0 Features
5.3 Base
UAS
Storage
Attachment
Locks
Belt Path for
Vehicle Belt
Installation
Foot
Adjustment
Lock Button
UAS
Connector
Storage
Webbing Release
Button
UAS Hooks Connectors
UAS Hooks Vehicle belt path
UAS Hooks Attachment
Your Safety Seat base can be installed with either the vehicle belt
or with the included UAS Hooks attachment system.
UAS Connector
storage in side
of base
23
24
5.0 Features 5.0 Features
5.4 Use of the Safety Seat with the Base
• To attach the Safety Seat to the Base,
align the Safety seat with the Base
and push down until the Safety Seat
latches onto the Base. Check that both
sides of the Safety Seat are securely
attached to the base. Rotate handle to
Rebound Position (Fig. 23-1).
Approved in vehicle
handle use positions
• The Rebound handle position is the
only approved in vehicle use position
(Fig. 23-2).
Fig. 23-1
Fig. 23-2
Rebound
Position
Rebound Position
Car Seat Removal from Base or Stroller
1- Rotate Carry Handle to the carry position.
2- Locate the red release handle behind the head.
end of the car seat. Squeeze the handle to engage
the base release (Fig. 24-1).
3- Lift Car Seat by the Carry Handle and Base Release handle
simultaneously. Do Not lift by front of car seat.
Fig. 24-1
(1)
(2)
(3)
(3)
25
26
5.0 Features 5.0 Features
Fig. 25-1
5-Point Harness
5.5 Other Features
Harness
We manufacturer several different styles of
Safety Seat each with various levels of features,
adjustments, and weight and size ratings. Please
follow the instructions that correspond with the
features included on your particular model.
Crotch Strap
The crotch strap is adjustable in length to ensure
a safe and comfortable t for harness.
Seat Angle Indicator
Level line indicator: use
with child greater than
10 to 15.8 kg (22 to 35
lbs). Ensure the angle
indicator line is level with
the ground to keep the
child’s airway open (Fig.
25-1).
Level Line
Indicator
Bubble level indicator for
use with Child
1.8 to 10 kg
(4 to 22 lbs)
. This Seat Angle
Indicator is used to ensure
that the seat is installed at
the proper degree of recline
keep the child’s airway open
and to adequately protect
your child in a crash.
Locking Clip
The Locking Clip is stored on the back
of the seat and is used to securely install
the Safety Seat with certain types of
vehicle lap/shoulder combination belts.
Seat Angle Adjuster
The Seat Angle Adjuster raises and
lowers the rear of the Base in order to
obtain the proper angle of recline for
proper installation of the Safety Seat
when using the Base.
Seat Angle
Indicator
Locking Clip
Seat Angle Adjuster
Center
CC7906A1118
35
FAILURE TO INSTALL SAFETY SEAT AT CORRECT SEAT ANGLE CAN
CAUSE DEATH OR SERIOUS INJURY
SEAT ANGLE INDICATOR
ADJUST FOOT OF BASE TO SET CORRECT SEAT ANGLE FOR WEIGHT OF CHILD.
SEE INSTRUCTION MANUAL FOR DETAILS.
Child Weight: 1.8 to 15.8 kg (4
-
35 lbs) Child Height: 81.3 cm or less (32 inches)
WARNING
DEATH OR SERIOUS INJURY can occur,
Level this line w
ith the ground
for children greater than 10 kg (22 lbs.).
- Use only in a rear-facing position when using it in the vehicle.
- Use only with children who weigh between 1.8 and 15.8 kg (4 and 35
pounds) and whose height is 81.3 cm (32 inches) or less.
- Snugly adjust the belts provided with this child restraint around your child.
- Secure this child restraint with the vehicle child restraint anchorage
system, UAS, if available or with a vehicle seat belt.
- Follow all instructions on this child restraint and in the written
instructions located on the side of this child restraint.
- Register your child restraint with the manufacture. Register online
at http://www.babytrend.com/registration.html
- Do not place this restraint in a vehicle seat that has an active
frontal air bag. If an active frontal air bag inflates it can hit the car
seat with great force and cause death or serious injury to your child.
- The carry handle must be in the Rebound position when using it in the vehicle.
Center bubble for
children 1.8-10kg (4-22 lbs).
Bulle du centre pour les
enfants pesant entre 1,8 et
10 kg (4 et 22 lb).
CC7908A1118
27
28
5.0 Features 5.0 Features
5.6 Operation of the Carry Handle
The Carry Handle has ve positions: the rebound position,
forward mid-storage position, mid-storage position, storage
position and the non-rocking position.
For vehicle use:
• The Rebound handle position is the
ONLY approved in vehicle use position.
To adjust handle position
• Depress the two buttons located on the
handle just above the connection to the Car
Seat shell to release the handle.
Carry Mid-Storage Storage Non-Rocking
Toys or other objects attached to carry handle can cause
injury in a crash. Never attach toys or other objects to
handle when in vehicle.
WARNING
Rebound
• Slowly rotate the handle to the
desired position. The buttons
should pop out and the handle
should automatically lock into the
new position (Fig. 28-1).
• Before lifting the Car Seat, push
on the handle to check that both
sides of the handle have locked
into the Carry position.
5.7 Attaching the Canopy
Slip the canopy fabric through the
canopy rod. Attach the canopy by
inserting the ends of the canopy
plastic stays into the female ttings
found on the inside of the handle
hub. Press rmly until the ends click
into position.
Failure to properly adjust the harness on your child
increases the risk of death or serious injury in the event
of a sharp turn, sudden stop or crash. Please follow the
instructions very closely to ensure that the harness is
properly adjusted to t your child at all times. Your child will
grow very rapidly! Please check the t of the harness every
time you use the Safety Seat.
WARNING
Fig. 28-1
29
30
5.0 Features 5.0 Features
5.8 Adjustment of the Shoulder Straps
The Safety Seat features three height
adjustments for the harness shoulder
straps. The harness straps must be used
in the slots that position the straps to
be even with or just below your child’s
shoulders (Fig. 29-1). The harness straps
are adjusted as follows:
1. Remove the Safety Seat from the Base
and rotate the Carry Handle to the back
position. Place your child in the Safety
Seat such that your child’s bottom is all
the way to the rear and bottom of the
seat.
2. Determine which pair of slots will
position the harness straps even with
or just below your child’s shoulders. DO
NOT use harness slots that will position
the harness straps above your child’s
shoulders as the harness straps in this
position will not restrain a small child in a
sharp turn, sudden stop or crash.
3. If the Harness Straps require
adjustment, remove your child from the
Safety Seat. Rotate the handle to the
upright carry position.
Fig. 29-1
Fig. 29-2
4. Loosen the harness straps by
depressing the Harness Adjuster Button
located below the ap just ahead of
the Harness Buckle and pulling on the
harness straps.
5. Turn the seat over. Locate the Belt
Adjuster Plate near the bottom of the seat
(Fig. 29-2). Remove both Harness Straps
from the Belt Adjuster Plate. From the
front of the seat, pull the Harness Straps
through the shoulder area slots and seat
pad. Never remove adjuster from Belt
Adjuster Plate (Fig. 30-1).
6.
Using the included Belt Threading Tool,
insert the Harness Straps through the Slots
selected in step 2 above, in the seat pad
and the seat shell, respectively
(Fig. 30-2).
7. From the rear of the Safety Seat, pull the
Harness Straps through the Slots until
you have enough strap to reach the Belt
Adjuster Plate.
8. Reassemble the Harness Straps to the Belt
Adjuster Plate. Do the left Harness Strap
rst, followed by the right Harness Strap.
Check that Harness Straps are completely
within the Belt Adjuster Plate loop
(Fig. 30-3).
Fig. 30-1
Fig. 30-2
Fig. 30-3
31
32
5.0 Features 5.0 Features
You have three adjustment positions on the
harness. Use Position A for a smaller child, and
Position B or C for a larger child.
If using Position A, loop B and C must be
on top of the Belt Adjuster Plate (Fig. 31-1).
9. Inspect the Harness Straps from the front and
rear to ensure that they are not twisted. Twisted
straps can prevent proper tightening of the
Harness and thus may not adequately restrain
your child in a sharp turn, sudden stop or crash.
10. Before using the Safety Seat, please pull on the
Harness Straps from the front to ensure that
they are securely reattached.
11.
When your harness is set at the correct childs position, attach the
excess harness straps with the hook and loop on the rear side
(Fig. 31-2). NEVER route webbing over the release bar (Fig. 31-3).
Fig. 31-2 Fig. 31-3
5.9 Low Birth Weight Adjustment
The Crotch Shortening clip is only to
be used with children whose weight is
between 1.8 to 4.5 kg (4 to 10 lbs) if the
gap between the buckle and thigh is not
between 1/2” and 1”. The crotch strap
length should be adjusted such that a
gap of 1/2” to 1” is present between the
ears of the buckle, and the top of the
child’s thigh, disregarding any clothing
or diaper (Fig. 32-1). Your child will grow
very quickly so always check that the
buckle is the proper height whenever
placing your child in the Safety Seat.
The crotch strap length is adjusted as
follows:
1a. Stored Shortening Clip: The
shortening clip is stored on the back of
the carrier (Fig. 32-2). To thread and
unthread as needed see the diagram
(Fig. 32-3).
1b. Threading And Unthreading The
Shortening Clip: To unthread the
metal stamping push the strap from
the side and slide it through the center
opening. Repeat for the other side.
1c. Flip over and repeat step 1.
Fig. 32-1
Fig. 32-2
Fig. 32-3
1/2 to 1 inch above thigh
Fig. 31-1
33
34
5.0 Features 5.0 Features
Fig. 33-4
Fig. 34-1
Fig. 33-3
Fig. 33-2
Fig. 33-1
1d. To thread the stamping back into
the strap slip the strap through the
center by reversing steps 1b and 1c.
2. Insert the sewn Anchor stamping
and the woven positioner stamping
thru the inner most slot, slot #1
(Fig. 33-1) - (Fig. 33-2).
3. View from underside. Pull slack as
needed (Fig. 33-3).
4. Thread the sewn anchor stamping
from the bottom of shell thru the
middle slot for storage. This storage
is so that the sewn anchor will not
interfere with function or cause a
mis-latch with shell and base when
the “low birth weight” positioner
stamping is used (Fig. 33-4).
Seat Cut-Away
Buckle
Anchor Bracket
Belt Shortening Clip
5. To shorten the buckle webbing length, thread
the anchor bracket through the slot forward of
the use position. Conrm the Anchor Bracket
is completely through the forward slot. Pull on
webbing from the bottom side of the safety
seat to conrm the Anchor Bracket is secured
in place (Fig. 34-1).
Seat Cut-Away
Buckle
Anchor Bracket
3 2 1
35
36
6.0 INFANT RESTRAINT 6.0 INFANT RESTRAINT
6.1 Securing your Child in the Safety Seat / Carrier
USING INFANT RESTRAINT
Your child must meet ALL these requirements:
• Weight between 1.8 and 15.8 kg (4 and 35 lbs).
• Height is 81.3 cm (32 inches) or less.
• The Harness Straps must be at or just
BELOW child’s shoulders when in highest
adjustment position.
Failure to properly secure your child in the Safety Seat /
Carrier increases the risk of death or serious injury from
suffocation or falls, or in the event of a sharp turn, sudden
stop or crash.
Children have STRANGLED in
loose or partially buckled harness
straps. Fully restrain the child
even when carrier is used outside
the vehicle.
WARNING
In a crash, the safety seat provides no protection for
your child unless the Harness Straps are properly
installed according to these instructions. Make sure
that the harness straps are properly adjusted and
secured whenever using the Safety Seat, even when
using as a carrier.
Please follow these instructions carefully to properly
secure your child.
1. Check that the Harness Straps are installed in
the proper slots or adjusted to the proper height
as described in section 5.8, Adjustment of the
Shoulder Straps, preceding.
2. The clothing you dress your child
in will affect the proper use of the
Safety Seat. Please dress your
child in clothing that will:
Allow the Harness Straps to securely latch between
your child’s legs.
• Keep the shoulder straps properly located on your
child’s shoulders.
37
38
6.0 INFANT RESTRAINT 6.0 INFANT RESTRAINT
3. Place the Safety Seat on a rm and
level surface. Move the carry handle
to the non rocking position. Loosen
the Harness Straps by pulling on the
straps while pushing on the Harness
Adjuster Button located below the pad
just in front of the buckle. Unfasten
the Harness Chest Clip. Unbuckle the
Harness Straps and drape the Harness
Straps over the Seat back or to the
sides of the Safety Seat (Fig. 37-1).
4. Place your child in the Safety Seat so
that the child’s bottom is against the
back and bottom of the seat (Fig. 37-2).
5. Pull the harness straps down over your
child. Check that the harness straps are
not twisted.
Fig. 37-1
Fig. 37-2
Correct
Incorrect
6.2 For the 5-Point Harness
• Type A: Put the two buckle tongues together,
overlaying the left buckle tongue onto the
right buckle tongue, and insert the two joined
buckle tongues into the harness buckle on
the crotch strap (Fig. 38-1). Type B: Insert
each buckle tongue into the harness buckle
(Fig. 38-2).
Make sure that you hear the tongues click
into the buckle and check that both are rmly
latched by pulling upward on the straps. If
the harness straps are not securely buckled,
the safety seat will NOT provide protection
for your child. DO NOT use the safety seat,
even as a carrier, if the harness does not
securely buckle. Please call Baby Trend at
1-800-328-7363 for assistance.
• From the front of the Safety Seat, pull outward on the Harness
Adjuster Strap to tighten the Harness Straps. Make sure that both
Harness Straps are at and snug on your child’s shoulders. A
snug strap should not allow any slack. It lies in a relatively straight
line without sagging. It does not press on the child’s esh or push
the child’s body into an unnatural position.
Fig. 38-1
Fig. 38-2
• Fasten the Harness Chest Clips together.
Position the Harness Chest Clip, by
sliding the Clip either up or down on the
Harness Straps, so that it is level with the
child’s armpits
(Fig. 38.3)
.
Fig. 38-3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Baby Trend Canadian Ally 35 Infant Seat Owner's manual

Category
Car seat
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI