BenQ MS630ST User manual

MS630ST/MX631ST/MW632ST

Digital Projector

User Manual

Table of contents2

Ta b l e o f c o nte n t s

Important safety

instructions ........................... 3

Introduction.......................... 7

Projector features.....................................7

Shipping contents ......................................8

Projector exterior view...........................9

Controls and functions ..........................10

Positioning your

projector..............................14

Choosing a location................................14

Obtaining a preferred projected

image size..................................................15

Connection .........................17

Connecting video source devices........18

Connecting smart devices.....................19

Operation............................20

Starting up the projector ......................20

Adjusting the projected image .............21

Using the menus......................................23

Securing the projector...........................24

Switching input signal .............................26

Magnifying and searching for

details.........................................................27

Selecting the aspect ratio ......................28

Optimizing the image .............................30

Setting the presentation timer.............33

Remote paging operations ....................34

Freezing the image ..................................34

Hiding the image......................................35

Operating in a high altitude

environment.............................................35

Adjusting the sound................................35

Using the test pattern............................ 36

Shutting down the projector ............... 37

Direct power off.....................................37

Menu operation ...................................... 38

Maintenance........................ 48

Care of the projector............................ 48

Lamp information ................................... 49

Troubleshooting ................ 55

Specifications ...................... 56

Projector specifications......................... 56

Dimensions .............................................. 57

Ceiling mount installation..................... 57

Timing chart.............................................58

Warranty and Copyright

information ......................... 62

Important safety instructions 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information

technology equipment. However, to ensure safe use of this product, it is important that

you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before

you operate your projector. Save

it for future reference.

2. Do not look straight at the

projector lens during operation.

The intense light beam may damage

your eyes.

3. Refer servicing to qualified

service personnel.

4. Always open the lens shutter (if

any) or remove the lens cap (if

any) when the projector lamp is

on.

5. In some countries, the line voltage is

NOT stable. This projector is

designed to operate safely within a

mains voltage between 100 to 240

volts AC, but could fail if power cuts

or surges of ±10 volts occur. In

areas where the mains voltage

may fluctuate or cut out, it is

recommended that you connect

your projector through a power

stabilizer, surge protector or

uninterruptible power supply

(UPS).

6. Do not block the projection lens with

any objects when the projector is

under operation as this could cause

the objects to become heated and

deformed or even cause a fire. To

temporarily turn off the lamp, press

ECO BLANK on the projector or

remote control.

Important safety instructions4

Safety Instructions (Continued)

7. The lamp becomes extremely hot

during operation. Allow the projector

to cool for approximately 45 minutes

prior to removing the lamp assembly

for replacement.

8. Do not operate lamps beyond the

rated lamp life. Excessive operation of

lamps beyond the rated life could

cause them to break on rare

occasions.

9. Never replace the lamp assembly or

any electronic components unless the

projector is unplugged.

10. Do not place this product on an

unstable cart, stand, or table. The

product may fall, sustaining serious

damage.

11. Do not attempt to disassemble this

projector. There are dangerous high

voltages inside which may cause death

if you should come into contact with

live parts. The only user serviceable

part is the lamp which has its own

removable cover.

Under no circumstances should you

ever undo or remove any other

covers. Refer servicing only to

suitably qualified professional service

personnel.

12. When the projector is under

operation, you may sense some

heated air and odor from its

ventilation grill. It is a normal

phenomenon and not a product

defect.

Important safety instructions 5

Safety Instructions (Continued)

13. Do not place this projector in any of

the following environments.

- Space that is poorly ventilated or

confined. Allow at least 50 cm

clearance from walls and free flow of air

around the projector.

- Locations where temperatures may

become excessively high, such as the

inside of a car with all windows rolled

up.

- Locations where excessive humidity,

dust, or cigarette smoke may

contaminate optical components,

shorten the projector's life span and

darken the image.

- Locations near fire alarms

- Locations with an ambient temperature

above 40°C / 104°F

- Locations where the altitudes are higher

than 3000 m (10000 feet).

14. Do not block the ventilation holes.

- Do not place this projector on a

blanket, bedding or any other soft

surface.

- Do not cover this projector with a cloth

or any other item.

- Do not place inflammables near the

projector.

If the ventilation holes are seriously

obstructed, overheating inside the

projector may result in a fire.

15. Always place the projector on a level,

horizontal surface during operation.

- Do not use if tilted at an angle of more

than 10 degrees left to right, nor at

angle of more than 15 degrees front to

back. Using the projector when it is not

fully horizontal may cause a malfunction

of, or damage to, the lamp.

16. Do not stand the projector on end

vertically. Doing so may cause the

projector to fall over, causing injury or

resulting in damage to the projector.

3000 m

(10000 feet)

0 m

(0 feet)

Important safety instructions6

Safety Instructions (Continued)

17. Do not step on the projector or place

any objects upon it. Besides probable

physical damage to the projector, doing

so may result in accidents and possible

injury.

18. Do not place liquids near or on the

projector. Liquids spilled into the

projector may cause it to fail. If the

projector does become wet,

disconnect it from the power supply's

power outlet and call BenQ to have

the projector serviced.

19. This product is capable of displaying

inverted images for ceiling mount

installation.

Use only BenQ's Ceiling Mount Kit for

mounting the projector and ensure it is

securely installed.

20. This apparatus must be earthed.

Ceiling mounting the projector

We want you to have a pleasant

experience using your BenQ projector,

so we need to bring this safety matter

to your attention to prevent possible

damage to person and property.

If you intend to mount your projector

on the ceiling, we strongly recommend

that you use a proper fitting BenQ

projector ceiling mount kit and that

you ensure it is securely and safely

installed.

If you use a non-BenQ brand projector

ceiling mount kit, there is a safety risk

that the projector may fall from the

ceiling due to an improper attachment

through the use of the wrong gauge or

length screws.

You can purchase a BenQ projector

ceiling mount kit from the place you

purchased your BenQ projector. BenQ

recommends that you also purchase a

separate Kensington lock compatible

security cable and attach it securely to

both the Kensington lock slot on the

projector and the base of the ceiling

mount bracket. This will perform the

secondary role of restraining the

projector should its attachment to the

mounting bracket become loose.

Hg - Lamp contains mercury. Manage in

accordance with local disposal laws. See

www.lamprecycle.org.

Introduction 7

Introduction

Projector features

The projector offers the following features

• SmartEco™ starts your dynamic power saving

The SmartEco™ technology offers a new way of operating the projector lamp system

and saves lamp power depending on the content brightness level.

• Longest lamp life with SmartEco™ technology

The SmartEco™ technology lowers the power consumption and increases the lamp

life.

• ECO BLANK saves the lamp power

Pressing the ECO BLANK button to hide the image and immediately lower the lamp

power at the same time.

• Less than 0.5W in standby condition

Less than 0.5W power consumption under standby mode.

• Filter Free

Filter free design to lower maintenance and operating costs.

• One-key auto-adjustment

Pressing AUTO on the keypad or remote control to show the best picture quality

immediately.

• Built-in 10W speaker(s)

Built-in 10W speaker(s) providing mixed mono audio when an audio input is connected

• Quick Cooling, Auto Power Off, Direct Power On

Quick Cooling function speeds up the cooling process when turning off the

projector. Auto Power Off function allows the projector to turn off automatically if

no input signal is detected after a set period of time. Direct Power On boots up the

projector automatically when the power is connected.

• 3D Function supported

Various 3D formats make the 3D function more flexible. By presenting the depth of the

images, you can wear BenQ 3D glasses to enjoy the 3D movies, videos and sporting

events in a more realistic way.

• The apparent brightness of the projected image will vary depending on the ambient lighting conditions,

selected input signal contrast/brightness settings, and is directly proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This

is normal and expected behavior.

Introduction8

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items

are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

*The warranty card is only supplied in some specific regions. Please consult your dealer for detailed

information.

Optional accessories

Projector Power cord VGA cable

Quick start guide User manual CD Warranty card*

Remote control with batteries

Digital Projector

Quick Start Guide

1. Spare lamp kit

2. Ceiling mount kit

3. RS232 cable

4. Carry bag

Introduction 9

Projector exterior view

1. External control panel

(See "Controls and functions" on page 10

for details.)

2. Lamp cover

3. Vent (heated air exhaust)

4. Quick-release button

5. Focus and Zoom ring

6. Vent (cool air intake)

7. Speaker grill

8. Front IR remote sensor

9. Projection lens

10. Lens cap

11. AC power jack

12. RS232 control port

13. USB Type-A port

14. USB Mini-B port

15.

Rear IR remote sensor

16. HDMI-input port

17. HDMI (MHL)-input port

18. RGB (PC)/Component Video (YPbPr/

YCbCr) signal input jack

19. RGB signal output jack

20. S-Video input jack

Video input jack

21. Audio (L/R) input jacks

22. Audio input jack

Audio output jack

23. Kensington anti-theft lock slot

24. Rear adjuster foot

25.

Front adjuster foot

26. Ceiling mount holes

27. PointWrite module mounting hole

28. Security bar

2

1

3

4

6

7

10

5

9

8

Front/upper side

12 13 14 15 16 17 18 19 222120

23

11

24

25

26

28

27

Rear/lower side

Introduction10

Controls and functions

Projector

1. Focus ring

Adjusts the focus of the projected image.

2. Zoom ring

Adjusts the size of the image.

3. LAMP indicator light

Indicates the status of the lamp. Lights up

or flashes when the lamp has developed a

problem.

4. MENU/EXIT

Turns on the On-Screen Display (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

5. Left/

Decreases the projector volume.

6. MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

7. ECO BLANK

Used to hide the screen picture.

8. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection.

9. TEMPerature warning light

Lights up red if the projector's

temperature becomes too high.

10. POWER indicator light

Lights up or flashes when the projector is

under operation.

11. AUTO

Automatically determines the best picture

timings for the displayed image.

12. POWER

Toggles the projector between standby

mode and on.

13. Right/

Increases the projector volume.

When the On-Screen Display (OSD)

menu is activated, the #5, #8, and #13

keys are used as directional arrows to

select the desired menu items and to

make adjustments.

14. SOURCE

Displays the source selection bar.

1

2

3

9

11

10

8

13

12

14

4

5

7

8

6

Introduction 11

Remote control

1. ON/ OFF

Toggles the projector between standby

mode and on.

2. Source selection buttons

(COMPUTER 1, COMPUTER 2,

VIDEO, S-VIDEO, HDMI,

NETWORK

)

Selects an input source for display.

3. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection.

4. MENU/EXIT

Turns on the On-Screen Display (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

5. Left/

Decreases the projector volume.

6. MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

7. ECO BLANK

Used to hide the screen picture.

8. LASER

Emits visible laser pointer light for

presentation purposes.

9. MHL control buttons

(Previous, Play/Pause,

Next, Rewind, Stop,

Fast-forward)

Goes to the previous file/Plays/Pauses/Goes

to the next file/Rewinds/Stops/Fast-forwards

during media playback.

Only available when controlling your smart

device in MHL mode.

10. ZOOM+/ZOOM-

Magnifies or reduces the projected picture

size.

11. PAGE+/PAGE-

Operate your display software program (on

a connected PC) which responds to page up/

down commands (like Microsoft

PowerPoint).

12. FREEZE

Freezes the projected image.

13. NETWORK SETTING

(No function.)

14. Quick Install

Quickly selects several functions to adjust

the projected image and displays the test

pattern.

15. AUTO

Automatically determines the best picture

timings for the displayed image.

16. Right/

When the On-Screen Display (OSD) menu

is activated, the #5, #3, and #16 keys are

used as directional arrows to select the

desired menu items and to make

adjustments.

2

3

4

8

9

11

12

13

14

10

6

5

7

1

15

19

20

21

22

16

17

3

18

2

3

4

11

12

13

23

10

6

5

7

1

15

19

20

21

22

16

17

3

18

For Japan

Introduction12

Controlling your smart device with the remote control

When the projector projects the content from your MHL compatible smart device, you

can use the remote control to control your smart device.

To enter the MHL mode, press and hold AUTO for 3 seconds. The following buttons are

available for controlling your smart device: Arrow keys ( / Up, / Down,

Left, Right), MENU/EXIT, MODE/ENTER, #0-#9, MHL control buttons.

To leave the MHL mode, press and hold AUTO for 3 seconds.

Remote control effective range

The remote control must be held at an angle within 30 degrees perpendicular to the

projector's IR remote control sensor(s) to function correctly. The distance between the

remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on

the projector that might obstruct the infra-red beam.

17. SOURCE

Displays the source selection bar.

18. MIC/VOL+/MIC/VOL-

(No function.)

19. MUTE

Toggles projector audio between on and

off.

20. ASPECT

Selects the display aspect ratio.

21. SMART ECO

Displays the Lamp Mode

menu for

selecting a suitable lamp operating mode.

22. Numeric buttons

(No function.)

23. TEST

Displays the test pattern.

Operating the LASER pointer

The Laser Pointer is a

presentation aid for professionals.

It emits red colored light when

you press it.

The laser beam is visible. It is

necessary to press and hold

LASER for continuous output.

Do not look into the laser light

window or shine the laser light beam on yourself or

others. See the warning messages on the back of the

remote control prior to using it.

The laser pointer is not a toy. Parents should be

mindful of the dangers of laser energy and keep

this remote control out of the reach of children.

• Operating the projector from the front

A

p

r

o

x

.

+

3

0

º

• Operating the projector from the rear

A

p

r

o

x

.

+

3

0

º

Introduction 13

Replacing the remote control batteries

1. Open the battery cover as illustrated.

2. Remove any existing batteries (if necessary) and install two AAA batteries observing

the battery polarities as indicated in the base of the battery compartment. Positive

(+) goes to positive and negative (-) goes to negative.

3. Refit the cover by aligning it with the base and snapping it back down into position.

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the

kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local environment

regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are dead or if you will not be using the remote control for an extended period of time,

remove the batteries to avoid damage to the remote control from possible battery leakage.

Positioning your projector14

Positioning your projector

Choosing a location

Your projector is designed to be installed in one of four possible installation locations:

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable

power outlet, as well as the location and distance between the projector and the rest of

your equipment.

1. Front Table

Select this location with the projector

placed on the table in front of the screen.

This is the most common way to position

the projector for quick setup and

portability.

2. Front Ceiling

Select this location with the projector

suspended upside-down from the ceiling in

front of the screen.

Purchase the BenQ Projector Ceiling

Mount Kit from your dealer to mount your

projector on the ceiling.

Set Front Ceiling in the SYSTEM

SETUP: Basic > Projector Installation

menu after you turn the projector on.

3. Rear Ceiling

Select this location with the projector

suspended upside-down from the ceiling

behind the screen.

Note that a special rear projection screen

and the BenQ Projector Ceiling Mount Kit

are required for this installation location.

Set Rear Ceiling in the SYSTEM

SETUP: Basic > Projector Installation

menu after you turn the projector on.

4. Rear Table

Select this location with the projector

placed on the table behind the screen.

Note that a special rear projection screen

is required.

Set Rear Table in the SYSTEM SETUP:

Basic > Projector Installation menu

after you turn the projector on.

Positioning your projector 15

Obtaining a preferred projected image size

The distance from the projector lens to the screen, the zoom setting, and the video format

each factors in the projected image size.

Projection dimensions

Refer to "Dimensions" on page 57 for the center of lens dimensions of this projector

before calculating the appropriate position.

MS630ST/MX631ST

The screen aspect ratio is 4:3 and the projected picture is in a 4:3 aspect ratio

For example, if you are using an 120-inch screen, the recommended projection distance is

2422 mm and the vertical offset is 91 mm.

If your measured projection distance is 3.0 m (3000 mm), the closest match in the

"Distance from screen (mm)" column is 3028 mm. Looking across this row shows that a

150'' (about 3.8 m) screen is required.

Screen size Distance from screen (mm)

Ver t ic a l

offset

(mm)

Diagonal

W

(mm)

H (mm)

Min

length

Average

Max

length

Inch mm

(max.

zoom)

(min.

zoom)

40 1016 813 610 734 807 881 30

50 1270 1016 762 917 1009 1101 38

60 1524 1219 914 1101 1211 1321 46

80 2032 1626 1219 1468 1615 1761 61

100 2540 2032 1524 1835 2018 2202 76

120 3048 2438 1829 2202 2422 2642 91

150 3810 3048 2286 2752 3028 3303 114

200 5080 4064 3048 3670 4037 4404 152

220 5588 4470 3353 4037 4440 4844 168

250 6350 5080 3810 4587 5046 5505 191

300 7620 6096 4572 5505 6055 6606 229

H

W

Projection distance

Center of lens

Screen

Vertical offset

4:3 Screen diagonal

Positioning your projector16

MW632ST

The screen aspect ratio is 16:10 and the projected picture is in a 16:10 aspect ratio

For example, if you are using an 120-inch screen, the recommended projection distance is

2063 mm and the vertical offset is 40 mm.

If your measured projection distance is 3.0 m (3000 mm), the closest match in the

"Distance from screen (mm)" column is 3094 mm. Looking across this row shows that a

180'' (about 4.6 m) screen is required.

All measurements are approximate and may vary from the actual sizes.

BenQ recommends that if you intend to permanently install the projector, you should physically test the

projection size and distance using the actual projector in situ before you permanently install it, so as to make

allowance for this projector's optical characteristics. This will help you determine the exact mounting position

so that it best suits your installation location.

Screen size Distance from screen (mm)

Ver t ic a l

offset

(mm)

Diagonal

W

(mm)

H (mm)

Min

length

Average

Max

length

Inch mm

(max.

zoom)

(min.

zoom)

40 1016 862 538 625 688 750 13

60 1524 1292 808 938 1031 1125 20

80 2032 1723 1077 1250 1375 1500 27

100 2540 2154 1346 1563 1719 1875 34

120 3048 2585 1615 1875 2063 2250 40

140 3556 3015 1885 2188 2406 2625 47

160 4064 3446 2154 2500 2750 3000 54

180 4572 3877 2423 2813 3094 3375 61

200 5080 4308 2692 3125 3438 3750 67

250 6350 5385 3365 3906 4297 4688 84

300 7620 6462 4039 4688 5156 5625 101

H

W

Projection distance

Center of lens

Screen

Vertical offset

16:10 Screen diagonal

Connection 17

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

• In the connections shown below, some cables may not be included with the projector (see "Shipping

contents" on page 8). They are commercially available from electronics stores.

• The connection illustrations below are for reference only. The rear connecting jacks available on the

projector vary with each projector model.

78 8 84

1

2 1 63 5

9 10

10

Notebook or desktop

computer

Speakers

A/V device

Monitor

(DVI)

(VGA)

or

Smartphone

or tablet PC

Connection18

• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key

combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/

LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key

simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

• The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER jack.

• If you wish to use this connection method when the projector is in standby mode, make sure the

Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See "Standby Settings"

on page 47 for details.

Connecting video source devices

You need only connect the projector to a video source device using just one of the

connecting methods, however each provides a different level of video quality. The method

you choose will most likely depend upon the availability of matching terminals on both the

projector and the video source device as described below:

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio

functionality accompanying data presentations for business purposes only. They are not

designed for, nor intended for stereo audio reproduction use as might be expected in

home theater or home cinema applications. Any stereo audio input (if provided), is mixed

into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 18 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source

has been selected, check that the video source device is turned on and operating correctly. Also check

that the signal cables have been connected correctly.

1. VGA cable

2. VGA to DVI-A cable

3. USB cable

4. Component Video to VGA (D-Sub)

adapter cable

5. S-Video cable

6. Video cable

7. Audio L/R cable

8. Audio cable

9. HDMI cable

10. HDMI-Micro USB cable

Te r m i n a l n a m e Terminal appearance Picture quality

HDMI

Best

Component Video

Better

S-Video

Good

Video

Normal

Connection 19

Connecting smart devices

The projector can project the content directly from a MHL compatible smart device. Using

a HDMI to Micro USB cable or a HDMI to Micro USB adaptor, you can connect your smart

devices to the projector and then enjoy your content on the big screen.

Some smart devices may not be compatible to the cable that you use. Please consult the manufacturer of your

smart device for detailed information.

Using a HDMI to Micro USB cable

1. Take a HDMI to Micro USB cable and connect one end to the MHL input connector

on the projector.

2. Connect the other end to the Micro USB output socket on your smart device.

3. Switch to the HDMI/MHL input source. To switch input signal, see "Switching input

signal" on page 26 for details.

Using a HDMI to Micro USB adaptor and a HDMI cable

1. Take a HDMI cable and connect one end to the MHL input connector on the

projector.

2. Connect the other to the HDMI input socket on the adaptor.

3. Connect the other of the adaptor to the Micro USB output socket on your smart

device.

4. Switch to the HDMI/MHL input source. To switch input signal, see "Switching input

signal" on page 26 for details.

Power

Operation20

Operation

Starting up the projector

1. Plug the power cord into the projector and into a

power outlet. Turn on the power outlet switch

(where fitted). Check that the POWER indicator

light on the projector lights orange after power

has been applied.

Please use the original accessories (e.g. power cord) only with the

device to avoid possible dangers such as electric shock and fire.

2. Press POWER or ON to start the projector. As soon as the lamp lights up,

a "Power On Ring Tone" will be heard. The POWER indicator light flashes

green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a

startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 36

for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds

before energizing the lamp.

3. If the projector is activated for the first

time, select your OSD language following

the on-screen instructions.

4. If you are prompted for a password, press

the arrow keys to enter a six-digit

password. See "Utilizing the password

function" on page 24 for details.

5. Switch all of the connected equipment on.

6. The projector will start to search for input

signals. The current input signal being

scanned appears in the upper left corner of

the screen. If the projector doesn't detect

a valid signal, the message “No Signal” will

continue displaying until an input signal is

found.

You can also press SOURCE on the

projector or remote control to select your

desired input signal. See "Switching input

signal" on page 26 for details.

• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the

message “Out of Range” displayed on the background screen. Please change to an input signal which is

compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on

page 58 for details.

• If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode.

Page is loading ...

BenQ MS630ST User manual

This manual is also suitable for

BenQ MS630ST User manual

Related papers

Other documents