Model No. WLEMBE71000
Serial No.
Write the serial number in the
space above for reference.
Part No. 171938 R1100A Printed in Korea © 2000 ICON Health & Fitness, Inc.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
ORDERING REPLACEMENT PARTS
If you encounter any difficulties or problems with this product, contact the ICON Fitness Lifestyle Ltd. office, or
write:
ICON Fitness Lifestyle Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
Tel: Country Code: 0345-089009
Fax: 0113-2411120
To help us assist you, please be prepared to give the following information:
• The MODEL of the product (WLEMBE71000)
• The NAME of the product (WESLO
®
BENCH 600 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 15 and the EXPLODED
DRAWING attached in the centre of this manual).
USER'S MANUAL
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
QUESTIONS?
As a manufacturer, we are
committed to providing
complete customer satisfaction.
If you have questions, or if
there are missing parts, we will
guarantee complete satisfaction
through our Customer Service
Department.
Please CALL:
Or WRITE:
ICON Health & Fitness Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
0345-089009
0345-089009
Serial
Number
Decal
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO ADJUST THE WEIGHT BENCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and an EXPLODED DRAWING are attached in the centre of this manual.
Remove the PART IDENTIFICATION CHART and the EXPLODED DRAWING before beginning assembly.
WESLO is a registered trademark of ICON Health & Fitness, Inc.
15
PART LIST—Model No. WLEMBE71000 R1100A
Key No. Qty. Description
1 14 5/16” Nylon Locknut
2 2 5/16” x 2 1/2” Bolt
3 10 5/16” Washer
4 1 1” Round Angle Cap
5 2 5/16” x 5 1/2” Bolt
6 11 1 1/2” Square Inner Cap
7 8 1/4” x 5/8” Screw
8 2 1/2” x 7/8” Spacer
9 1 5/16” x 4” Bolt
10 4 5/16” x 2” Bolt
11 2 1/2” x 7/16” Spacer
12 11 1” Round Inner Cap
13 3 Weight Stop
14 1 3/8” x 2 1/2” Bolt
15 4 3/8” Nylon Locknut
16 12 3/4” Round Inner Cap
17 1 Large Lock Pin
18 4 5 1/2” Foam Pad
19 2 7” Foam Pad
20 2 6” Foam Pad
21 4 Foam Grip
22 2 Medium Lock Pin
23 2 3/4” x 1 3/4” Spacer
24 3 1/2” x 5/16” Spacer
25 2 5/16” x 4 1/2” Bolt
26 2 2 3/4” Spacer
27 2 Spring Clip
28 2 Square Outer Bushing
29 1 Knob
30 1 Lower Cable
31 1 Square Plate
32 2 5/16” x 2 1/4” Bolt
33 1 “U” Bracket
Key No. Qty. Description
34 3 3/8” x 1 1/2” Bolt
35 2 Square Inner Bushing
36 3 Pulley
37 1 Upper Cable
38 1 Small Lock Pin
39 3 Cable Clip
40 1 Lat Tower
41 1 Weight Carriage
42 1 Lat Bar
43 1 Curl Pad
44 1 Curl Tube
45 1 Leg Lever
46 1 14” Weight Tube
47 2 Short Pad Tube
48 1 Long Pad Tube
49 1 Right Stabiliser
50 1 Left Stabiliser
51 1 Frame
52 1 “H” Frame
53 4 7/8” Round Inner Cap
54 1 Backrest
55 2 Weight Rest
56 1 Seat
57 1 Left Arm
58 1 Right Arm
59 1 Left Backrest Bracket
60 1 Right Backrest Bracket
61 1 Adjustment Tube
62 2 9” Pad Tube
63 2 11” Weight Tube
64 2 Weight Clip
65 2 Stabiliser Plate
# 1 User’s Manual
Note: “#” Indicates an non-illustrated part. See the back cover of this manual for information about ordering
replacement parts. Specifications are subject to change without notice.
To find the parts listed below, refer to the EXPLODED DRAWING attached in the centre of this manual.
14 3
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
REMOVING AND ATTACHING THE LAT TOWER
To remove the Lat Tower (40), first remove the
Knob (29) from the Frame (51). Next, remove the
indicated 5/16” x 2” Bolt (10), 5/16” Washers (3),
and 5/16” Nylon Locknut (1). Lift the Lat Tower out
of the Frame.
To attach the Lat Tower (40), slide the Lat Tower
into the Frame (51). Attach the Lat Tower to the
Frame with the 5/16” x 2” Bolt (10), the two 5/16”
Washers (3), and the 5/16” Nylon Locknut (1). Fully
tighten the Knob (29) into the Frame.
Note: Make sure that a 1 1/2” Square Inner Cap
(not shown) is inserted into the Frame (51)
when the Lat Tower (40) is not attached.
USING THE CURL PAD AND CURL TUBE
To use the Curl Pad (43), insert the Curl Tube (44)
into the Frame (51). Raise the Curl Upright to the
desired height, and align one of the holes in the
Curl Tube with the hole in the Frame. Insert the
Small Locking Pin (38) through the Frame and the
Curl Tube. Rotate the Small Locking Pin to the
locked position, with the Small Locking Pin clipped
onto the Frame.
Note: Make sure that a 1 1/2” Square Inner Cap
(not shown) is inserted in the Frame (51) when
the Curl Pad (43) and Curl Tube (44) are not
attached.
SECURING THE LEG LEVER
When the Leg Lever (45) is not being used, it must
be secured with the Large Locking Pin (17). To
secure the Leg Lever, hold the Leg Lever against
the Frame (51). Slide the Large Locking Pin
through the hole in the Leg Lever and secure it
behind the Frame as shown.
29
10
3
1
40
51
43
38
17
45
51
44
51
1. Read all instructions in this manual before
using the weight bench.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor or carpet.
5. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
6. Inspect the cables before each use. Make
sure that the cables remain on the pulleys at
all times. If a cable binds while you are exer-
cising, stop immediately and make sure that
the cable is on the pulleys. Replace both
cables every two years.
7. The weight bench is designed to be used by
only one person at a time.
8. Keep children under 12 and pets away from
the weight bench at all times.
9. Always wear athletic shoes for foot protec-
tion while exercising.
10. Keep hands and feet away from moving
parts.
11. Do not place more than 365 pounds (165 kg)
on the weight rests; do not place more than
125 pounds (57 kg) on the leg lever; do not
place more than 30 pounds (14 kg) on the
arms.
12. When using the weight carriage, always
secure your weights (not included) with the
weight clips.
13. Remove the lat bar when performing any
exercise that does not require the lat bar.
14. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
15. The decal shown below has been placed on
the weight bench. If the decal is missing or
illegible, please call our Customer Service
Department at 0345-089009 to order a free
replacement decal. Apply the replacement
decal in the location shown.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
134
BEFORE YOU BEGIN
Adjustment Tube
Lat Bar
Low Pulley
Leg Lever
Weight Tube
Weight Tube
Weight Rest
Lock Pin
Weight Carriage
Backrest
Seat
Arm
Thank you for selecting the versatile WESLO
®
BENCH
600 weight bench. The BENCH 600 offers a selection
of weight stations designed to develop every major
muscle group of the body. Whether your goal is to tone
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the BENCH 600
will help you to achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department at
0345-089009. To help us assist you, please note the
product model number and serial number before call-
ing. The model number is WLEMBE71000. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labelled.
High Pulley
USING THE WEIGHT CARRIAGE
To use the high pulley station or the low pulley sta-
tion, make sure that the Upper Cable (37) is
attached to the Weight Carriage (41) with a Cable
Clip (39). Slide the desired weights (not included)
onto the weight tube of the Weight Carriage.
Secure the weights with the Weight Clips (64).
When using the Weight Carriage, always secure
the weights with the Weight Clips.
USING THE HIGH PULLEY STATION
Attach the Lat Bar (42) to the Upper Cable (37) with
a Cable Clip (39).
USING THE LOW PULLEY STATION
Attach the Lower Cable (30) to the Upper Cable
(37) with a Cable Clip (39). Attach the Lat Bar (42)
to the other end of the Lower Cable with a Cable
Clip (39).
41
37
64
64
39
37
39
39
42
37
30
39
42
Weight
Weight
12 5
ASSEMBLY
1
2
3
49
50
1
1
52
Before beginning assembly, carefully read the
following information and instructions:
• Place all parts of the weight bench in a cleared
area and remove the packing materials; do not
dispose of the packing materials until assembly is
completed.
• For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the centre of this manual.
Note: Some small parts may have been pre-
attached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.
• As you assemble the weight bench, Make sure
that all parts are oriented as shown in the
drawings.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
• Two (2) adjustable spanners
• One (1) phillips screwdriver
• One (1) rubber mallet
• Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be easier if you have a socket set or
a set of open-end or closed-end wrenches.
If further assistance is needed, please call our
Customer Service Department at 0345-089009.
1. Before beginning assembly, make sure that
you have read the information in the box
above.
Attach the Right Stabiliser (49) to the “H” Frame
(52) with a 5/16” x 2 1/2” Bolt (2), a 5/16” Washer
(3), and a 5/16” Nylon Locknut (1). Do not tight-
en the Nylon Locknut yet.
Attach the Left Stabiliser (50) to the “H” Frame
(52) with a 5/16” x 2 1/2” Bolt (2), a 5/16” Washer
(3), and a 5/16” Nylon Locknut (1). Do not tight-
en the Nylon Locknut yet.
HOW TO ADJUST THEWEIGHT BENCH
The instructions below describe how each part of the weight bench can be adjusted. Inspect and tighten all parts
each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with
a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
To use the Backrest (54) in an inclined position, first
remove the Medium Lock Pins (22). Raise the
Backrest and insert the Adjustment Tube (61) through
one of the three sets of large holes in the “H” Frame
(52). As you insert the Adjustment Tube, adjust the
height of the Weight Rests (55) and insert the
Adjustment Tube through one of the three sets of
large holes in the Weight Rests. Rotate the
Adjustment Tube to the locked position, with the end
of the Adjustment Tube clipped onto the “H” Frame.
Lay the Backrest on the Adjustment Tube.
To use the Backrest (54) in a level position, remove
the Adjustment Tube (61). Lay the Backrest on the
Frame (51). Use the Medium Lock Pins (22) to adjust
the height of the Weight Rests (55) (see ADJUSTING
THE WEIGHT RESTS below).
ADJUSTING THE WEIGHT RESTS
When the Backrest (54) is in the level position, the
Weight Rests (55) must be secured with the Medium
Lock Pins (22). Raise the Weight Rests to the desired
height, and align one of the holes in each Weight
Rest with the small hole in the “H” Frame (52). Insert
the Medium Lock Pins through the “H” Frame and the
Weight Rests. Rotate the Medium Lock Pins to the
locked position, with the Medium Lock Pins clipped
onto the “H” Frame. Make sure that both Weight
Rests are at the same height.
ATTACHING WEIGHTS TO THE WEIGHT BENCH
To use the Arms (57, 58), make sure that there is a
Weight Stop (13) on each 11” Weight Tube (63). Slide
the desired amount of weight (not included) onto each
Weight Tube. Do not place more than 30 pounds
(14 kg) on each Arm.
To use the Leg Lever (45), make sure that there is a
Weight Stop (13) on the 14” Weight Tube (46). Slide
the desired amount of weight (not included) onto the
Weight Tube. Do not place more than 125 pounds
(57 kg) on the Leg Lever.
52
58
13
63
Weight
61
55
22
22
55
45
Weight
46
54
51
52
54
55
22
22
55
13
2
3
11
2. Press two 1 1/2” Square Inner Caps (6) into the
Frame (51). Press a 1 1/2” Square Inner Cap
(6) into each of the Stabilisers (49, 50).
Attach the Frame (51) to the “H” Frame (52)
with two 5/16” x 2 1/4” Bolts (32) and two 5/16”
Nylon Locknuts (1). Do not tighten the Nylon
Locknuts yet.
Attach the Frame (51) to the Stabilisers (49, 50)
with two 5/16” x 5 1/2” Bolts (5), the two
Stabiliser Plates (65), and two 5/16” Nylon
Locknuts (1).
Tighten all of the Nylon Locknuts (1) used in
this step and step 1.
3. Attach the Left and Right Backrest Brackets
(59, 60) to the Backrest (54) with four 1/4” x
5/8” Screws (7). Make sure that the Brackets
are oriented so the indicated holes are on
the end shown. Note: The Screws may come
pre-inserted into the Backrest.
4. Tap 3/4” Round Inner Caps (16) into the indicat-
ed ends of the Adjustment Tube (61). Insert the
Adjustment Tube into the “H” Frame (52) as
shown.
Attach the Left and Right Backrest Brackets
(59, 60) to the Frame (51) with the 5/16” x 4”
Bolt (9), two 1/2” x 7/8” Spacers (8), and a
5/16” Nylon Locknut (1).
5. Attach the Seat (56) to the Frame (51) with two
1/4” x 5/8” Screws (7).
6
5
2
5
1
6
6
32
52
65
65
50
49
7
7
Holes
Toward
Wide End
Of Backrest
59
60
54
16
16
1
8
9
51
59
52
60
56
7
51
51
1
3
4
61
18. Attach the Lower Cable (30) to the Upper Cable
(37) with a Cable Clip (39).
Wrap the Lower Cable (30) around a Pulley
(36). Attach the Pulley to the “U” Bracket (33)
with a 3/8” x 1 1/2” Bolt (34) and a 3/8” Nylon
Locknut (15).
19. Wet the ends of the Lat Bar (42) with soapy
water. Slide a Foam Grip (21) onto each end of
the Lat Bar. Press a 1” Round Inner Cap (12)
into each end of the Lat Bar.
20. Make sure that all parts are properly tight-
ened before you use the weight bench. The
use of all remaining parts will be explained on
pages 12 to 14.
18
19
39
30
37
36
34
15
33
42
21
21
12
12
10
6. Press 1 1/2” Square Inner Caps (6) into both
ends of the Leg Lever (45).
Attach the 14” Weight Tube (46) to the Leg
Lever (45) with a 5/16” x 2” Bolt (10), two 5/16”
Washers (3), a 1/2” x 5/16” Spacer (24), and a
5/16” Nylon Locknut (1).
Press the 1” Round Angle Cap (66) onto the
indicated end of the Weight Tube (46). Tap a 1”
Round Inner Cap (12) into other end of the
Weight Tube. Slide a Weight Stop (13) onto the
Weight Tube.
7. Lubricate the 3/8” x 2 1/2” Bolt (14). Attach the
Leg Lever (45) to the Frame (51) with the Bolt
and a 3/8” Nylon Locknut (15).
8. Press a 3/4” Round Inner Cap (16) into each
end of a Short Pad Tube (47). Insert the Pad
Tube into one of the holes in the Leg Lever
(45). Slide a 5 1/2” Foam Pad (18) onto each
end of the Pad Tube.
Repeat for the other Short Pad Tube (47).
Press a 3/4” Round Inner Cap (16) into each
end of the Long Pad Tube (48). Insert the Pad
Tube into the indicated hole in the Frame (51).
Slide a 6” Foam Pad (20) onto each end of the
Pad Tube.
9. Press two Square Outer Bushings (28) onto the
“H” Frame (52).
Wet the inside of a Foam Grip (21) with soapy
water. Slide the Foam Grip onto a Weight Rest
(55). Press a 1” Round Inner Cap (12) into the
Weight Rest. Slide the Weight Rest into one
side of the “H” Frame. Align one of the small
holes in the Weight Rest with the small hole in
the “H” Frame (52). Insert a Medium Lock Pin
(22) through the Weight Rest and the “H”
Frame.
Assemble the other Weight Rest (55) in the
same way.
7
9
6
10
6
3
3
24
1
45
46
6
12
66
13
14
15
45
20
20
18
18
48
47
16
16
51
12
52
22
22
45
51
7
8
55
21
28
16. Slide the Lat Tower (40) into the Frame (51).
The Lat Tower must be turned as shown.
Attach the Lat Tower to the Frame with a 5/16”
x 2” Bolt (10), two 5/16” Washers (3), and a
5/16” Nylon Locknut (1). Fully tighten the Knob
(29) into the Frame.
17. Locate the Upper Cable (37), which has a ball
on one end. Insert the Upper Cable through the
top of the Lat Tower (40) as shown.
Attach a Pulley (36) inside the Lat Tower (40)
with a 3/8” x 1 1/2” Bolt (34) and a 3/8” Nylon
Locknut (15). Make sure that the ball is on
the indicated side of the Pulley and that the
Upper Cable (37) is between the Pulley and
the welded rod.
Attach the other Pulley (36) inside the Lat
Tower (40) in the same way.
Attach the Upper Cable (37) to the Weight
Carriage (41) with a Cable Clip (39).
16
17
40
51
1
29
34
36
36
40
41
39
37
Ball
Welded
Rod
15
10
3
10. Press a 7/8” Round Inner Cap (53) into the
Right Arm (58). Insert two 1 1/2" Square Inner
Caps (6) into the Right Arm.
Attach an 11” Weight Tube (63) to the Right
Arm (58) with a 5/16” x 4 1/2” Bolt (25), a 5/16”
Washer (3), a 1/2” x 5/16” Spacer (24), a 2 3/4”
Spacer (26), and a 5/16” Nylon Locknut (1).
Insert 1” Round Inner Caps (12) into both ends
of the Weight Tube (63). Slide a Weight Stop
(13) onto the Weight Tube.
Assemble the Left Arm (not shown) in the same
manner.
11. Insert a 3/4” x 1 3/4” Spacer (23) into the weld-
ed tube on the “H” Frame (52). Lubricate the
axle on the Right Arm (58). Insert the axle into
the welded tube. Make sure that the 2 3/4”
Spacer (26, see drawing 10) is on the outside
of the “H” Frame. Insert a Spring Clip (27) into
the axle so that it locks into the hole in the axle.
Insert a 7/8” Round Inner Cap (53) into the
welded tube.
Attach the Left Arm (not shown) in the same
manner.
12. Attach a 9” Pad Tube (62) to the Right Arm (58)
with a 5/16” x 2” Bolt (10), two 5/16” Washers
(3), a 1/2” x 7/16” Spacer (11), and a 5/16”
Nylon Locknut (1).
Press two 3/4” Round Inner Caps (16) into the
9” Pad Tube (62). Slide a 7” Foam Pad (19)
onto the Pad Tube.
Repeat this step for the Left Arm (not shown).
13. Attach the Curl Pad (43) to the Curl Tube (44)
with two 1/4” x 5/8” Screws (7).
8 9
13
10
11
12
53
58
1
26
25
24
3
6
6
13
12
27
53
58
52
10
3
3
11
16
58
1
16
19
7
43
44
63
Lubricate Axle
62
Welded Tube
14. Press Square Inner Bushings (35) into the top
and bottom of the Weight Carriage (41). Press
a 1” Round Inner Cap (12) into each side of the
Weight Carriage.
Slide the Weight Carriage (41) onto the Lat
Tower (40). The Weight Carriage must be
turned so the weight tube is on the side
shown and the welded tab is pointed toward
the top of the Lat Tower.
15. Insert the “U” Bracket (33) into the indicated
hole in the Lat Tower (40). Attach the “U”
Bracket with a Square Plate (31) and a 5/16”
Nylon Locknut (1). Make sure that the “U”
Bracket is on the side of the Lat Tower
shown.
14
15
35
35
41
12
12
Welded Tab
Weight Tube
40
33
31
1
40
23
3/8" Nylon Locknut (15)–4
1 1/2" Square Inner Cap (6)–11
Spring Clip (27)–2
5/16" Nylon Locknut (1)–14
3/8" x 2 1/2" Bolt (14)–1
5/16" Washer (3)–10
1/2" x 7/8" Spacer (8)–2
5/16" x 5 1/2" Bolt (5)–2
5/16" x 4" Bolt (9)–1
1/2" x 7/16” Spacer (11)–2
1" Round Inner Cap (12)–11
3/4" x 1 3/4" Spacer (23)–2
5/16" x 4 1/2" Bolt (25)–2
3/8" x 1 1/2" Bolt (34)–3
7/8" Round Inner Cap (53)–4
3/4" Round Inner Cap (16)–12
5/16" x 2" Bolt (10)–4
5/16" x 2 1/4" Bolt (32)–2
5/16" x 2 1/2" Bolt (2)–2
2 3/4” Plastic Sleeve (26)-2
Weight Stop (13)–3
1/2" x 5/16" Spacer (24)–3
1/4" x 5/8" Screw (7)–8
REMOVE THIS PART IDENTIFICATION CHART
AND EXPLODED DRAWING FROM THE MANUAL
This chart is provided to help you identify the small parts used in assembly. Important: Some parts may have
been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it
has been pre-assembled. The number in parenthesis below each part refers to the key number of the part. The
second number refers to the quantity needed for assembly.
23
3
11
53
1
10
6
3
62
1
26
24
3
25
16
12
19
63
12
13
58
1
1
50
49
6
51
20
1
18
16
47
16
4
46
13
12
30
6
39
35
35
10
1
29
18
17
15
14
45
12
12
36
34
15
33
31
1
12
36
34
15
36
40
21
42
21
12
19
16
13
12
6
57
10
3
11
3
1
53
1
26
12
24
3
25
7
44
43
7
7
55
54
60
59
22
22
16
61
52
3
2
9
48
16
16
7
28
8
1
20
62
63
56
23
41
12
21
12
21
10
3
24
3
1
38
27
2
3
6
5
6
32
1
1
53
53
6
27
16
16
6
16
37
6
65
65
64
EXPLODED DRAWING—Model No. WLEMBE71000 R1100A
To identify parts shown on this EXPLODED DRAWING, refer to the
PART LIST on page 15.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
