Traceable 4367 Owner's manual

Traceable
Brand
Traceable
Model
4367
Category
Measuring, testing & control
Type
Owner's manual

Traceable 4367

The Traceable 4367 is a versatile and reliable salinity meter that can measure salinity in a wide range of liquids, from pure water to seawater. It features:

  • Automatic Temperature Compensation (ATC): Ensures accurate readings regardless of the temperature of the liquid being measured.
  • Multiple Measurement Ranges: 0.00 to 10.00 ppt (NaCl) and 10.1 to 70.0 ppt (NaCl) for measuring a variety of salinity levels.
  • Hold Function: Freezes the display to allow for easy recording of readings.
  • Auto-Off Function: Automatically turns off the meter after 20 minutes of inactivity to conserve battery life.

Traceable 4367

The Traceable 4367 is a versatile and reliable salinity meter that can measure salinity in a wide range of liquids, from pure water to seawater. It features:

  • Automatic Temperature Compensation (ATC): Ensures accurate readings regardless of the temperature of the liquid being measured.
  • Multiple Measurement Ranges: 0.00 to 10.00 ppt (NaCl) and 10.1 to 70.0 ppt (NaCl) for measuring a variety of salinity levels.
  • Hold Function: Freezes the display to allow for easy recording of readings.
  • Auto-Off Function: Automatically turns off the meter after 20 minutes of inactivity to conserve battery life.
◄
SPECIFICATIONS
Salinity—
Range: 0.00 to 10.00 ppt (NaCl)
Resolution: 0.01
Range: 10.1 to 70.0 ppt (NaCl)
Resolution: 0.01
Automatic Temperature Compensation—
Range: 32.0 to 122.0 °F / 0.0 to 50.0 °C
Normalization: 25°C(xed)
Temperature Measurement—
Range: 32.0 to 122.0 °F / 0.0 to 50.0 °C
Resolution: 0.1°
OPERATION
Thissectioncontainsbasicoperatinginstructions,to
insureaccurateresultsandformoreadvancedfunctions,
refertotheadditionalsectionsthatfollow.
1.Removetheprotectivecoverfromtheprobehead.
2.Turnthemeteronbypressingthe
ON/OFF
SET
button.
3.Placetheprobeheadintothesolutiontobemeasured.
4.ToinsureAutomaticTemperatureCompensation,
immersetheprobeheadandtemperaturesensor
completely.ForaccurateAutomaticTemperature
Compensation,thetemperaturesensormustreach
equilibriumwiththeliquidbeingmeasured,thiscould
takeseveralminutes.
5.Insurethatthereisadequatemovementoftheliquid
aroundthetipoftheprobehead(0.2-0.3metersper
secondminimum).Thiscanbeachievedbystirringthe
meterintheliquid.
Themeterwillautomaticallyselecttherangethatis
themostappropriateforthevaluebeingmeasured.To
manuallyselecttherange,pressandholdthe
Ç
button
forapproximatelythree(3)seconds(seethe“Range
ModeSelection”section).
6.Takethedesiredmeasurements.
7.Pressthe
ON/OFF
SET
buttontoturnthemeteroff.
Topreservebatterylife,alwaysturnthemeteroffwhen
notinuse.
8.Rinsetheprobeheadwithdistilled/deionizedwaterand
replacetheprotectivecover.Alwaysreplacethe
protectivecovertopreventdamagetotheprobehead.
Ifnobuttonispressedfortwenty(20)minutes,themeter
willturnoffautomaticallytopreservebatterylife(seethe
“AutomaticShutoff”section).
POWER ON DISPLAY SEQUENCE
Whenthemeteristurnedon(bypressingthe
ON/OFF
SET
button),thedisplaywillcyclethroughshowingthe
followingitems:
AllSegments-Displaycheck
tnr Normalizationtemperaturevalue(seethe
“SelectingTemperatureNormalizationValue”
section)
ran Rangedisplaymode(seethe“RangeMode
Selection”section).
SALINITY CALIBRATION
Onecalibrationpointmaybeenteredforeachof
themeasurementranges(0.00to10.00pptand
10.1 to 70.0 ppt).
Toinsureaccuracy:
–Selectaknownstandardwithavalueascloseas
possibletothevalueoftheunknownsample.
–Ifpossible,theknownstandardandunknown
sampleshouldbeatthesametemperature.Theideal
temperatureis25°C.
Previouscalibrationpointsareclearedwhenthemeteris
calibratedtoanewvalue.
1.Removetheprotectivecoverfromtheprobehead.
2.Turnthemeteronbypressingthe
ON/OFF
SET
button.
3.Placetheprobeheadintotheknownstandard.
4.ToinsureAutomaticTemperatureCompensation,
immersetheprobeheadandtemperaturesensor
completely.ForaccurateAutomaticTemperature
Compensation,thetemperaturesensormustreach
equilibriumwiththeliquidbeingmeasured,thiscould
takeseveralminutes.
5.Insurethatthereisadequatemovementoftheliquid
aroundthetipoftheprobehead(0.2-0.3metersper
secondminimum).Thiscanbeachievedbystirringthe
meterintheliquid.
6.Pressandholdthe
È
HLD/CAL
buttonforapproximately
three(3)seconds,CALwillappearatthetopofthe
displayandtheconductivitymeasurementwillash.
7.Pressthe
Ç
and/or
È
HLD/CAL
buttonstoadjustthe
displaytotheknowvalueoftheknownstandard.
The meter may only be adjusted by ±30%
of the detected value.
8.Withthetheknowvalueoftheknownstandard
appearingandCALnolongerashing,pressthe
ON/OFF
SET
button,themeterwillreturntothe
measurementdisplay.
VIEWING CALIBRATION DATA
1.Turnthemeteronbypressingthe
ON/OFF
SET
button.
2.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,P1.0willappearatthebottomof
thedisplay.
3.Pressthe
Ç
buttontwo(2)times,P4.0will
appearatthebottomofthedisplay.
4.Pressthe
ON/OFF
SET
button,P4.1willappearatthe
bottomofthedisplay.Thetopofthedisplaywillshow
thevaluethatthemeterwascalibratedtoforthe
rangeof0.00to10.00ppt.(Ifnousercalibrationhas
beenperformed,“- - - ”willappear.)
5.Pressthe
Ç
button,P4.2willappearatthe
bottomofthedisplay.Thetopofthedisplaywill
showthevaluethatthemeterwascalibratedtoforthe
rangeof10.1to70.0ppt.(Ifnousercalibrationhas
beenperformed,“- - - ”willappear.)
6.Pressthe
ON/OFF
SET
button,P4.0 willappearatthe
bottomofthedisplay.
7.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,themeterwillreturntothe
measurementdisplay.
SELECTING °F OR °C
1.Turnthemeteronbypressingthe
ON/OFF
SET
button.
2.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,P1.0willappearatthebottomof
thedisplay.
3.Pressthe
ON/OFF
SET
button,thetemperatureunitof
measurewillashonthedisplay.
4.Pressthe
Ç
button,thetemperaturereadingwill
switchtotheoppositeunitofmeasure.Ifthemeter
hadbeendisplaying°F,itwillnowdisplay°C,and
vice-versa.Eachpressofthe
Ç
buttonwillswitch
thedisplaytotheoppositeunitofmeasure.
5.Withthedesiredunitofmeasureappearing,pressthe
ON/OFF
SET
buttonthree(3)times,P1.0 willappearatthe
bottomofthedisplay.
6.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,themeterwillreturntothe
measurementdisplay.
Theunitofmeasureselectedwillbethedefaultunitof
measureuntilchanged.
RANGE MODE SELECTION
Themeterwillautomaticallyselecttherangethatis
themostappropriateforthevaluebeingmeasured. To
manuallyselectthedisplayrange,pressandholdthe
Ç
buttonforapproximatelythree(3)seconds.
Eachtimethe
Ç
buttonforpressedandheld,therange
modewillcyclethroughtheavailablemodes:
ATO Automaticrangeselection
1 0.00 to 10.00 ppt
2 10.1 to 70.0 ppt
HOLD FUNCTION
Theholdfunctionallowsthereadingsonthedisplaytobe
“frozen”sothattheymayberecorded.
1.Pressandreleasethe
È
HLD/CAL
buttonto“freeze”
thedisplayatthecurrentreading.“HOLD”will
appearatthetopofthedisplay.
2.Oncethereadinghasbeenrecorded,pressand
releasethe
È
HLD/CAL
buttontoreturnthedisplayto
thecurrentreading.“HOLD”willnolonger
appearonthedisplay.
AUTOMATIC SHUTOFF (Disable)
Ifnobuttonhasbeenpressedfortwenty(20)minutes,
theAutomaticShutofffeaturewillturnthemeteroffto
preservebatterylife.
TodisabletheAutomaticShutofffeature:
1. Withthemeterturnedoff,pressandholdthe
È
HLD/CAL
button,thenpressandholdthe
ON/OFF
SET
buttonuntil
“n ”appearsonthedisplay.
2. Releasethe
È
HLD/CAL
and
ON/OFF
SET
buttons.Themeter
willpoweronandtheAutomaticShutofffeaturewill
bedisabled.
TheAutomaticShutofffeatureisautomaticallyenabled
whenthemeterispoweredoffandturnedbackon.
RESET TO FACTORY DEFAULTS
Resettingthemeterwillclearallcalibrationdataand
resetthetemperaturedisplayto°C.
Thefollowingprocedureisusedtoresetthemetertothe
factorydefaultvalues.
1.Turnthemeteronbypressingthe
ON/OFF
SET
button.
2.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,P1.0willappearatthebottomof
thedisplay.
3.Pressthe
Ç
buttonone(1)time,P3.0will
appearatthebottomofthedisplay.
4.Pressthe
ON/OFF
SET
button,the
n
willashonthedisplay.
5.Pressthe
Ç
button,the
y
willashonthedisplay.
6. With
y
appearing,pressthe
ON/OFF
SET
button,P3.0
willappearatthebottomofthedisplayandthevalues
willhavebeenresettothefactorydefaults.
7.Pressandholdthe
ON/OFF
SET
buttonforapproximately
three(3)seconds,themeterwillreturntothe
measurementdisplay.
TRACEABLE
SALINITY METER
INSTRUCTIONS
®
DISPLAY MESSAGES
Upper Display Messages:
--- Indicatesthatthemeterisinthemanual
rangeselectionmodeandthevaluebeing
measuredishigherthan10.00ppt.
E03 Indicatesthatthevalueofthesolutionbeing
measuredexceedsthemeasurementrangeof
theunit.
E04 Indicatesthatthevalueofthesolutionbeing
measuredexceedsthemeasurementrangeof
theunitbasedonatemperaturemeasurement
error(seethe“LowerDisplayMessages”section).
Lower Display Messages:
E0
1
Indicatesthatthetemperaturesensorisdamaged.
E0
2
Indicatesthatthetemperatureofthesolution
beingmeasuredisbelowthemeasurement
rangeoftheunit.
E0
3
Indicatesthatthetemperatureofthesolution
beingmeasuredisabovethemeasurement
rangeoftheunit.
ALL OPERATION DIFFICULTIES
Ifthismeterdoesnotfunctionproperlyforanyreason,
replacethebatterieswithanew,highqualitybatteries
(seethe“BatteryReplacement”section).Lowbattery
powercanoccasionallycauseannumberof“apparent”
operationaldifculties.Replacingthebatterieswithnew
freshbatterieswillsolvemostdifculties.
BATTERY REPLACEMENT
Anerraticdisplay,faintdisplay,nodisplay,orabattery
symbolappearingonthedisplayareallindicatorsthat
thebatteriesneedreplacement.Thebatterycoveris
locatedatthetopoftheunit.Unscrewthebatterycover
byturningitcounter-clockwise.Removetheexhausted
batteriesandreplacethemwithfour(4)new#357/LR44
sizesilveroxidebatteries.Makecertaintoinsertthe
newbatterieswiththeproperpolarityasindicatedbythe
“+”and“–”symbolsinthebatterycompartment.The
“+”sideofthesilveroxidebatteryistheatsidewith
theengraving.Replacethebatterycoverandtighten
securely.
WARRANTY, SERVICE, OR RECALIBRATION
Forwarranty,service,orrecalibration,contact:
CONTROL COMPANY
12554 Old Galveston Rd. Suite B230
Webster, Texas 77598 USA
Ph. 281 482-1714 • Fax 281 482-9448
E-mail [email protected]
www.traceable.com
Control Company is ISO 9001:2008 Quality-Certied
by DNV and ISO/IEC 17025:2005 accredited as a
Calibration Laboratory by A2LA.
Control Company Cat. No. 4367
Traceable
®
is a registered trademark of Control Company.
©
2016 Control Company. 92-4367-00 Rev. 1 061716
  • Page 1 1
  • Page 2 2

Traceable 4367 Owner's manual

Traceable
Brand
Traceable
Model
4367
Category
Measuring, testing & control
Type
Owner's manual

Traceable 4367

The Traceable 4367 is a versatile and reliable salinity meter that can measure salinity in a wide range of liquids, from pure water to seawater. It features:

  • Automatic Temperature Compensation (ATC): Ensures accurate readings regardless of the temperature of the liquid being measured.
  • Multiple Measurement Ranges: 0.00 to 10.00 ppt (NaCl) and 10.1 to 70.0 ppt (NaCl) for measuring a variety of salinity levels.
  • Hold Function: Freezes the display to allow for easy recording of readings.
  • Auto-Off Function: Automatically turns off the meter after 20 minutes of inactivity to conserve battery life.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents