Comfort Glow CS26PT Owner's manual

Brand: Comfort Glow

Model: CS26PT

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

CS26NT

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s in-

structions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

VENT-FREE FREESTANDING PEDESTAL STOVE SYSTEM

OWNER’S OPERATION AND INSTALLATION MANUAL

THERMOSTATICALLY - CONTROLLED MODELS

CS26PT AND CS26NT

20,000 TO 26,000 BTU/HR

www.desatech.com 113066-01A

WARNING: Improper installation, adjustment, altera-

tion, service, or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualified installer, service

agency, or the gas supplier.

WARNING: This is an unvented gas-fired heater. It uses

air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air

must be provided. Refer to

Air for Combustion and

Ventilation

section on page 5 of this manual.

This appliance may be installed in an aftermarket,*

permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases.

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identification .......................................... 4

Local Codes ........................................................ 5

Unpacking ........................................................... 5

Product Features ................................................ 5

Air For Combustion And Ventilation .................... 5

Installation ........................................................... 7

Operating Heater .............................................. 14

Inspecting Burners ............................................ 15

Cleaning and Maintenance ............................... 16

Service Hints ..................................................... 17

Technical Service .............................................. 17

Specifications .................................................... 17

Troubleshooting ................................................. 18

Illustrated Parts Breakdown and Parts List ....... 22

Replacement Parts ........................................... 26

Accessories ....................................................... 26

Parts Central ..................................................... 27

Warranty Information .......................... Back Cover

www.desatech.com

113066-01A 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects,

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, oper-

ate, or service this heater. Im-

proper use of this heater can

cause serious injury or death

from burns, fire, explosion, elec-

trical shock, and carbon mon-

oxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of car-

bon monoxide poisoning resemble the flu, with head-

aches, dizziness, or nausea. If you have these signs,

the fireplace may not be working properly. Get fresh

air at once! Have fireplace serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the influence

of alcohol, and those at high altitudes.

Natural and Propane/LP Gas:

Natural and Propane/LP

gases are odorless. An odor-making agent is added to

these gases. The odor helps you detect a gas leak.

However, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this fireplace.

WARNING: Any change to

this fireplace or its controls can

be dangerous.

WARNING: Do not allow fans

to blow directly into the heater.

Avoid any drafts that alter burner

flame patterns. Ceiling fans can

create drafts that alter burner

flame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger

insert, or other accessory not

approved for use with this

heater.

Due to high temperatures, the

appliance should be located out

of traffic and away from furni-

ture and draperies.

Do not place clothing or other

flammable material on or near

the appliance. Never place any

objects in the fireplace.

Heater becomes very hot when

running fireplace. Keep children

and adults away from hot sur-

faces to avoid burns or clothing

ignition. Fireplace will remain

hot for a time after shutdown.

Allow surfaces to cool before

touching.

Carefully supervise young chil-

dren when they are in the room

with fireplace.

You must operate this heater

with the heater screen in place.

Make sure heater screen is in

place before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline, and other flam-

mable vapors and liquids.

www.desatech.com 113066-01A

SAFETY INFORMATION

Continued

1. This appliance is only for use with the type of

gas indicated on the rating plate. This appli-

ance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors (propane/LP gas units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the fire department

4. This heater shall not be installed in a bedroom

or bathroom.

5. Do not use this heater as a wood-burning heater.

Use only the logs provided with the heater.

6. Do not add extra logs or ornaments such as pine

cones, vermiculite, or rock wool. Using these

added items can cause sooting. Do not add lava

rock around base. Rock and debris could fall

into the control area of heater. After servicing,

always replace screen before operating heater.

7. You must operate this heater with the heater

screen in place. Make sure heater screen is in

place before running heater.

8. This heater is designed to be smokeless. If logs

ever appear to smoke, turn off heater and call

a qualified service person.

Note:

During ini-

tial operation, slight smoking could occur due

to log curing and heater burning manufactur-

ing residues.

9. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 16.

10. Before using furniture polish, wax, carpet

cleaner, or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

11. This heater needs fresh air ventilation to run

properly. This heater has an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the heater if not enough fresh

air is available. See Air for Combustion and

Ventilation, page 5. If heater keeps shutting

off, see Troubleshooting, page 18.

12. Keep all air openings in front and bottom of

heater clear and free of debris. This will in-

sure enough air for proper combustion.

13. Do not run heater

• where flammable liquids or vapors are used

or stored.

• under dusty conditions.

14. Do not use this heater to cook food or burn

paper or other objects.

15. Do not use heater if any part has been under

water. Immediately call a qualified service

technician to inspect the room heater and to

replace any part of the control system and any

gas control which has been under water.

16. Turn off and unplug heater and let cool be-

fore servicing. Only a qualified service per-

son should service and repair heater.

17. Operating heater above elevations of 4,500

feet could cause pilot outage.

18. Do not operate heater if any log is broken. Do

not operate heater if a log is chipped (dime-

sized or larger).

19. To prevent performance problems with pro-

pane/LP units, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

20. Provide adequate clearances around air

openings.

PRODUCT

IDENTIFICATION

Heater Controls

Screen

Stove

Cabinet

Figure 1 - Vent-Free Freestanding

Pedestal Stove

One

Piece

Log Set

www.desatech.com

113066-01A 5

LOCAL CODES

Install and use heater with care. Follow all local

codes. In the absence of local codes, use the latest

edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

1. Remove top inner pack.

2. Tilt carton so that stove is upright.

3. Remove protective side packaging.

4. Slide stove out of carton.

5. Remove protective plastic wrap.

6. Remove screen by lifting and then pulling

forward.

7. Remove log set by cutting plastic ties.

8. Carefully unwrap log.

9. Check for any shipping damage. If stove or

log is damaged, promptly inform dealer where

you bought stove.

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion

Sensing (ODS) safety shutoff system. The ODS/

pilot is a required feature for vent-free room heat-

ers. The ODS/pilot shuts off the heater if there is

not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system re-

quires no matches, batteries, or other sources to

light heater.

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a confined space

or unusually tight construction

unless provisions are provided

for adequate combustion and ven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efficient than

ever. New materials, increased insulation, and new

construction methods help reduce heat loss in

homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy effi-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air

for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 5 through 7 will help

you classify your space and provide adequate ven-

tilation.

Unusually Tight Construction

The air that leaks around doors and windows may

provide enough fresh air for combustion and ven-

tilation. However, in buildings of unusually tight

construction, you must provide additional fresh air.

www.desatech.com 113066-01A

Unusually tight construction is defined as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10

-11

kg per pa-sec-m

)

or less with openings gasketed or

sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to ar-

eas such as joints around window and

door frames, between sole plates and

floors, between wall-ceiling joints, be-

tween wall panels, at penetrations for

plumbing, electrical, and gas lines, and

at other openings.

If your home meets all of these three crite-

ria, you must provide additional fresh air.

See

Ventilation Air From Outdoors

, page 7

If your home does not meet all of the three

criteria above, proceed to

Determining

Fresh-Air Flow For Fireplace Location

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1/NFPA

54 defines a confined space as a space whose vol-

ume is less than 50 cubic feet per 1,000 Btu per

hour (4.8 m

per kw) of the aggregate input rating

of all appliances installed in that space and an un-

confined space as a space whose volume is not less

than 50 cubic feet per 1,000 Btu per hour (4.8 m

per kw) of the aggregate input rating of all appli-

ances installed in that space. Rooms communicat-

ing directly with the space in which the appliances

are installed*, through openings not furnished with

doors, are considered a part of the unconfined space.

* Adjoining rooms are communicating only if there

are doorless passageways or ventilation grills be-

tween them.

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Confined or

Unconfined Space

Use this work sheet to determine if you have a

confined or unconfined space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

AIR FOR COMBUSTION

AND VENTILATION

Continued

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example:

Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft. (vol-

ume of space)

If additional ventilation to adjoining room is sup-

plied with grills or openings, add the volume of

these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example:

2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free fireplace __________ Btu/Hr

Gas water heater* __________ Btu/Hr

Gas furnace __________ Btu/Hr

Vented gas heater __________ Btu/Hr

Gas fireplace logs __________ Btu/Hr

Other gas appliances* + __________ Btu/Hr

Total = __________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free fireplace __________ Btu/Hr

Total __________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

________

Btu/Hr (maximum the space can support)

________

Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space

can support)

56,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a confined space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must pro-

vide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an uncon-

fined space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building, page 7.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size

makes room unconfined.

30,000

+ 26,000

= 56,000

www.desatech.com

113066-01A 7

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an uncon-

fined space. You will need no additional fresh air ven-

tilation.

WARNING: If the area in

which the heater may be oper-

ated is smaller than that defined

as an unconfined space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the

National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section

5.3

or applicable local codes

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

confined space. When ventilating to an adjoining

unconfined space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the floor on the wall connecting

the two spaces (see options 1 and 2, Figure 2).

You can also remove door into adjoining room (see

option 3, Figure 2). Follow the National Fuel Gas

Code, ANS Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills

or ducts. You must provide two permanent open-

ings: one within 12" of the ceiling and one within

12" of the floor. Connect these items directly to

the outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANS Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

IMPORTANT:

Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-con-

trolled power vent. Heated air entering the attic

will activate the power vent.

Figure 3 - Ventilation Air from Outdoors

Figure 2 - Ventilation Air from Inside

Building

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

Outlet

Air

Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

www.desatech.com 113066-01A

12"

Minimum

12"

Minimum

48"

Minimum

Ceiling

Side Wall Side Wall

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objects are less than 42 inches

from the front, top, or sides of

the heater

• in high traffic areas

• in windy or drafty areas

CAUTION: This heater creates

warm air currents. These currents

move heat to wall surfaces next to

heater. Installing heater next to

vinyl or cloth wall coverings or

operating heater where impuri-

ties (such as, but not limited to,

tobacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls or cause odors.

IMPORTANT:

Vent-free heaters add moisture to

the air. Although this is beneficial, installing heater

in rooms without enough ventilation air may cause

mildew to form from too much moisture. See Air

for Combustion and Ventilation, page 5.

CHECK GAS TYPE

Use correct gas type (natural or propane/LP). If

your gas supply is not correct, do not install heater.

Call dealer where you bought heater for proper

type heater.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

CLEARANCES TO COMBUSTIBLES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

floor, ceiling, and adjoining side

and back walls.

INSTALLATION

Continued

Carefully follow the instructions below. This stove

is a freestanding unit designed to set directly on

the floor.

IMPORTANT:

You must maintain mini-

mum wall and ceiling clearances during installa-

tion. The minimum clearances are shown in Fig-

ure 4. Measure from outermost point of stove top.

Minimum Wall and Ceiling Clearances

(see Figure 4)

A. Clearances from outermost point of stove top

to any combustible side wall should not be

less than 12 inches.

B. Clearances from outermost point of stove top

to any combustible back wall should not be less

than 6 inches (Includes corner installations).

C. Clearances from the stove top to the ceiling

should not be less than 48 inches.

Figure 4 - Minimum Clearance to Walls

and Ceiling

Front View

Top View

Side View

Front of

Stove Unit

Back Wall

Side Wall Side Wall

Minimum

48"

Minimum

Ceiling

Floor

Back Wall

Corner

Wall

Minimum

www.desatech.com

113066-01A 9

CONNECTING TO GAS SUPPLY

WARNING: A qualified ser-

vice person must connect heater

to gas supply. Follow all local

codes.

CAUTION: Never connect

propane/LP heater directly to the

propane/LP supply. This heater

requires an external regulator

(not supplied). Install the exter-

nal regulator between the heater

and propane/LP supply.

WARNING: Never connect

natural gas heater to private (non-

utility) gas wells. This gas is com-

monly known as wellhead gas.

Installation Items Needed

Before installing heater, make sure you have the

items listed below.

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* An CSA design-certified equipment shutoff

valve with 1/8" NPT tap is an acceptable alterna-

tive to test gauge connection. Purchase the optional

CSA design-certified equipment shutoff valve

from your dealer. See Accessories, page 26.

For propane/LP units, the installer must supply an

external regulator. The external regulator will re-

duce incoming gas pressure. You must reduce in-

coming gas pressure to between 11 and 14 inches

of water. If you do not reduce incoming gas pres-

sure, heater regulator damage could occur. Install

external regulator with the vent pointing down as

shown in Figure 6. Pointing the vent down pro-

tects it from freezing rain or sleet.

INSTALLATION

Continued

CAUTION: Use only new, black

iron or steel pipe. Internally-tinned

copper tubing may be used in

certain areas. Check your local

codes. Use pipe of 1/2"

diameter

or greater to allow proper gas

volume to heater. If pipe is too

small, undue loss of volume will

occur.

Installation must include an equipment shutoff

valve, union, and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up. NPT

tap must be upstream from heater (see Figure 7,

page 10).

IMPORTANT:

Install equipment shutoff valve in

an accessible location. The equipment shutoff

valve is for turning on or shutting off the gas to

the appliance.

Check building codes for any special requirements

for locating equipment shutoff valve to fireplaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from go-

ing into pipe. Excess sealant in pipe could result

in clogged heater valves.

Figure 5 - Gas Regulator Location and

Gas Line Access Into Stove Cabinet

Front

Stove

Unit

Gas Regulator

Inlet Connection

Side View

Figure 6 - External Regulator With Vent

Pointing Down

Propane/LP

Supply Tank

External

Regulator

Vent

Pointing

Down

Back View

www.desatech.com 113066-01A

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

We recommend that you install a sediment trap in

supply line as shown in Figure 7. Locate sediment

trap where it is within reach for cleaning. Install

in piping system between fuel supply and heater.

Locate sediment trap where trapped matter is not

likely to freeze. A sediment trap traps moisture

and contaminants. This keeps them from going into

heater controls. If sediment trap is not installed or

is installed wrong, heater may not run properly.

CAUTION: Avoid damage to

regulator. Hold gas regulator

with wrench when connecting it

to gas piping and/or fittings.

INSTALLATION

Continued

Propane/LP

From External Regulator

(11" W.C.** to 14" W.C.

Pressure)

Natural

From Gas Meter

(5" W.C.** to

10.5" W.C.

Pressure)

CSA Design-

Certified Equipment

Shutoff Valve With

1/8" NPT Tap*

Figure 7 - Gas Connection

* Purchase the optional CSA design-certified

equipment shutoff valve from your dealer. See

Accessories, page 26.

** Minimum inlet pressure for purpose of input

adjustment.

Tee

Joint

Pipe

Nipple

Cap

Min

Sediment Trap

Gas

Regulator

of Heater

Approved

Flexible Gas

Hose (if allowed

by local codes)

CHECKING GAS CONNECTIONS

WARNING: Test all gas pip-

ing and connections, internal

and external to unit, for leaks

after installing or servicing. Cor-

rect all leaks at once.

WARNING: Never use an

open flame to check for a leak.

Apply a noncorrosive leak de-

tection fluid to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater. See guidelines under

Con-

necting to Gas Supply

, page 9.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect heater with its appliance main gas

valve (control valve) and equipment shutoff

valve from gas supply piping system. Pres-

sures in excess of 1/2 psig will damage heater

regulator.

2. Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas, opening main gas valve lo-

cated on or near gas meter for natural gas, or

using compressed air.

4. Check all joints of gas supply piping system.

Apply noncorrosive leak detection fluid to gas

joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

valve to gas supply. Check reconnected fit-

tings for leaks.

Test Pressures Equal To or Less Than 1/2

PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 8,

page 11).

www.desatech.com

113066-01A 11

2. Pressurize supply piping system by either

opening propane/LP supply tank valve for

propane/LP gas, opening main gas valve lo-

cated on or near gas meter for natural gas, or

using compressed air.

3. Check all joints from gas meter to equipment

shutoff valve (see Figures 9 and 10). Apply

noncorrosive leak detection fluid to gas joints.

Bubbles forming show a leak.

4. Correct all leaks at once.

PRESSURE TESTING HEATER GAS

CONNECTIONS

1. Open equipment shutoff valve (see Figure 8).

2. Open main gas valve located on or near gas

meter for natural gas or open propane/LP sup-

ply tank valve for propane/LP gas.

3. Make sure control knob of heater is in the OFF

position.

4. Check all joints from equipment shutoff valve

to control valve (see Figures 9 and 10). Apply

noncorrosive leak detection fluid to gas joints.

Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operating Heater, page 14).

Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to Appli-

ance, page 15).

POSI

Figure 8 - Equipment Shutoff Valve

Closed

Equipment

Shutoff Valve

Open

Figure 9 - Checking Gas Joints

Control Valve

Location

Propane/LP

Supply Tank

Equipment

Shutoff Valve

INSTALLATION

Continued

Figure 10 - Checking Gas Joints

Gas Meter

Equipment Shutoff Valve

Control Valve

Location

INSTALLING LOGS

WARNING: Failure to position

the parts in accordance with these

diagrams or failure to use only

parts specifically approved with

this heater may result in property

damage or personal injury.

CAUTION: After installation

and periodically thereafter,

check to ensure that no flame

comes in contact with any log.

With the heater set to High, check

to see if flames contact any log.

If so, reposition logs according

to the log installation instruc-

tions in this manual. Flames con-

tacting logs will create soot.

It is very important to install the logs exactly as

instructed. Do not modify logs. Only use logs sup-

plied with heater.

Place one-piece log set over the burner as illus-

trated in Figure 11. Make sure log sits flat on fire-

box floor..

Figure 11 - Installing One-Piece Log Set

One Piece

Log Set

Firebox Floor

www.desatech.com 113066-01A

INSTALLATION

Continued

IMPORTANT:

Make sure log does not cover any

burner ports (see Figure 12).

Figure 12 - Installing One-Piece Log set

(Top View)

One Piece

Log Set

Burner Ports

INSTALLING BLOWER ACCESSORY

GA3750

Tools required: Phillips screwdriver

NOTICE: Shut off gas heater

during the following blower

installation.

1. Remove top panel of stove by removing six

screws - four from back and one from each

side (see Figure 13).

2. Disconnect power cord wires from blower

motor (if connected) (see Figure 14).

3. Disconnect green ground wire from blower

housing (if connected) by removing screw

holding wire terminal (see Figure 14).

4. Install one plastic bushing provided in blower

kit into the 1

/2" hole in the left rear of fire-

box floor. Access hole through the rectangu-

lar opening in the rear panel (see Figure 15).

5. Attach the two mounting brackets that were

packaged with the owner’s manual to blower

housing using four screws provided in blower

kit (2 for each bracket) (see Figure 16). Tighten

screws securely.

6. Working from the rear of the stove, place en-

tire power cord, including speed control hous-

ing, in lower control compartment.

7. Route ends of 3-wire power cord up from the

lower control compartment through the plas-

tic bushing, then up to the upper cavity of stove

(see Figure 17, page 13).

8. Attach the terminal ends of the white and black

power cord wires to the terminals on the

blower motor (see Figure 14). Push firmly.

9. Attach the terminal end of the green power

cord wire to the front tab of the blower hous-

ing using screw provided (see Figure 14).

Figure 13 - Removing Stove Top Panel

Figure 14 - Removing Wires from Blower

Screw

Green Ground Wire

White

Powercord

Wire

Black Powercord Wire

Figure 15 - Installing Bushing

Bushing

Figure 16 - Attaching Blower and Blower

Brackets to Stove Top

Blower

Bracket

Top of

Stove

www.desatech.com

113066-01A 13

INSTALLATION

Continued

10. Using four screws from hardware bag, mount

blower assembly to stove by attaching

blower brackets to stove top panel (see Fig-

ure 16, page 12). Tighten screws securely.

11. Working from the inside of the stove, insert

shaft of speed control housing into hole on

right side of stove next to the control knob/

piezo ignitor (see Figure 17). Place retainer

nut onto shaft by turning in a clockwise di-

rection until snug. Install plastic control knob

onto output shaft of speed control housing.

12. Check to make sure that the power cord is

completely clear of blower wheel and there

are no foreign objects in blower wheel.

13. Carefully replace stove top panel. Align holes

and replace six screws removed in step 1,

page 12.

14. Peel off the backing paper and stick the sup-

plied wiring diagram decal on the stove floor

as shown in Figure 17.

15. Plug power cord into a convenient 3-prong

grounded wall receptacle near the stove.

WARNING: Electrical Ground-

ing Instructions: This appliance

is equipped with a three-prong

(grounding) plug for your protec-

tion against shock hazard and

should be plugged directly into a

properly grounded three-prong

receptacle.

16. Using speed control knob, turn blower on and

check for operation.

17. All remaining parts from blower kit may be

discarded.

Power Cord

Speed

Control

Housing

Control

Knob

Figure 17 - Installing Blower Control

Housing

Wiring Diagram Decal

120 Vac.

60 Hz. .

78 Amps

Variable

Fan Switch

WhiteWhite

Black

Green

110/115

V.A.C.

Blower

Motor

Black

Off

WARNING: Never attempt to service heater while it

is plugged in, operating, or hot. Burns and electrical

shock could result. Only a qualified service person

should service or repair heater.

If any of the original wire as supplied with the appliance must be

replaced, it must be replaced with 105°C wire or it’s equivalent.

WARNING: Label all wires prior to disconnec-

tion when servicing controls. Wiring errors can

cause improper and dangerous operation. Verify

proper operation after servicing.

DESA Heating Products, Bowling Green, KY

Retainer

Nut

www.desatech.com 113066-01A

OPERATING HEATER

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a fire or explosion may result

causing property damage, per-

sonal injury or loss of life.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next

to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

C. Use only your hand to push in or turn the

gas control knob. Never use tools. If the

knob will not push in or turn by hand, don’t

try to repair it, call a qualified service tech-

nician or gas supplier. Force or attempted

repair may result in a fire or explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a quali-

fied service technician to inspect the appli-

ance and to replace any part of the control

system and any gas control which has been

under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation

of new heater, burning logs will

give off a paper-burning smell.

Orange flame will also be present.

Open a window to vent smell.

This will only last a few hours.

1. STOP! Read the safety information, above.

2. Make sure equipment shutoff valve is fully

open.

3. Turn control knob clockwise to the

OFF position.

4. Wait five (5) minutes to clear out any gas.

Then smell for gas, including near the floor.

If you smell gas, STOP! Follow “B” in the

safety information, column 1. If you don’t

smell gas, go to the next step.

5. Turn control knob counterclockwise

to the PILOT position. Press in control knob

for five (5) seconds (see Figure 18).

Note:

You may be running this heater for

the first time after hooking up to gas sup-

ply. If so, the control knob may need to be

pressed in for 30 seconds or more. This will

allow air to bleed from the gas system.

6. With control knob pressed in, press and re-

lease ignitor button. This will light pilot.

The pilot is attached to the front burner. If

needed, keep pressing ignitor button until

pilot lights.

Note:

If pilot does not stay lit, contact a

qualified service person or gas supplier for

repairs. Until repairs are made, light pilot

with match. To light pilot with match, see

Manual Lighting Procedure, page 15.

7. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob.

• If control knob does not pop out when re-

leased, contact a qualified service person

or gas supplier for repairs.

Note:

If pilot goes out, repeat steps 3

through 7. This heater has a safety inter-

lock system. Wait one (1) minute for sys-

tem to reset before lighting pilot again.

8. Turn control knob counterclockwise

to desired heating level. The burn-

ers should light. Set control knob to any

heat level between HI and LO.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

Figure 18 - Control Knob and Ignitor

Button Location

Control Knob

Ignitor Button

www.desatech.com

113066-01A 15

OPERATING HEATER

Continued

Figure 19 - Pilot

Thermocouple

Pilot Burner

Ignitor Electrode

INSPECTING BURNERS

Check pilot flame pattern and burner flame pat-

terns often.

PILOT FLAME PATTERN

Figure 20 shows a correct pilot flame pattern. Figure

21 shows an incorrect pilot flame pattern. The incor-

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise to the

OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise to the PI-

LOT position.

THERMOSTAT CONTROL

OPERATION

The thermostat control knob can be set to any

comfort level between HI and LO. The ther-

mostat will gradually modulate the heat out-

put and flame height from higher to lower set-

tings, or pilot, in order to maintain the comfort

level you select. The ideal comfort setting will

vary by household depending upon the amount

of space to be heated, the output of the central

heating system, etc.

Note:

Selecting the HI setting with the control

knob will cause the burners to remain fully on,

without modulating down in most cases.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Lighting In-

structions, page 14.

2. Depress control knob and light pilot with

match.

3. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob. Now follow step 8

Lighting Instructions, page 14

rect pilot flame is not touching the thermocouple.

This will cause the thermocouple to cool. When the

thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Fig-

ure 21

• turn heater off (see To Turn Off Gas to Appliance)

• see Troubleshooting, page 18

Note:

The correct pilot flame on natural gas units

will have a slight curve, but flame should be blue

an have no yellow or orange color.

BURNER FLAME PATTERN

Figure 22 shows a correct burner flame pattern.

Figure 23 shows an incorrect burner flame pat-

tern. If burner flame pattern is incorrect,

• turn heater off (see To Turn Off Gas to Appliance)

• see Troubleshooting, pages 18 through 21

Figure 20 - Correct Pilot Flame Pattern

(Natural Gas Shown)

Figure 21 - Incorrect Pilot Flame Pattern

(Natural Gas Shown)

Thermocouple

Pilot Burner

Thermocouple

Pilot Burner

Figure 22 - Correct Flame Pattern with

Control Knob Set to High Flame

Figure 23 - Incorrect Flame Pattern with

Control Knob Set to High Flame

Approx.

3-6"

Above

Top of

Logs

Than 8"

Above

Top of

Logs

www.desatech.com 113066-01A

CLEANING AND

MAINTENANCE

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep

control areas, burner, and cir-

culating air passageways of

heater clean. Inspect these ar-

eas of heater before each use.

Have heater inspected yearly by

a qualified service person.

Heater may need more frequent

cleaning due to excessive lint

from carpeting, bedding mate-

rial, pet hair, etc.

WARNING: Failure to keep

the primary air opening(s) of the

burner(s) clean may result in

sooting and property damage.

BURNER INJECTOR HOLDER AND

PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount

of air to mix with the gas. This provides a clean

burning flame. Keep these holes clear of dust, dirt,

lint, and pet hair. Clean these air inlet holes prior to

each heating season. Blocked air holes will create

soot. We recommend that you clean the unit every

three months during operation and have heater in-

spected yearly by a qualified service person.

We also recommend that you keep the burner tube

and pilot assembly clean and free of dust and dirt.

To clean these parts we recommend using com-

pressed air no greater than 30 PSI. Your local com-

puter store, hardware store, or home center may

carry compressed air in a can. You can use a

vacuum cleaner in the blow position. If using com-

pressed air in a can, please follow the directions

on the can. If you don't follow directions on the

can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow

the unit to cool for at least thirty minutes.

2. Inspect burner, pilot, and primary air inlet

holes on injector holder for dust and dirt (see

Figure 24).

3. Blow air through the ports/slots and holes in

the burner.

4. Check the injector holder located at the end

of the burner tube again. Remove any large

particles of dust, dirt, lint, or pet hair with a

soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the in-

jector holder.

6. In case any large clumps of dust have now been

pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the

pilot flame indicates dust and dirt in the pilot as-

sembly. There is a small pilot air inlet hole about

two inches from where the pilot flame comes out

of the pilot assembly (see Figure 25). With the

unit off, lightly blow air through the air inlet hole.

You may blow through a drinking straw if com-

pressed air is not available.

Figure 24 - Injector Holder On Outlet

Burner Tube

Figure 25 - Pilot Inlet Air Hole

Burner

Tube

Pilot

Assembly

Pilot Air

Inlet Hole

Ports/Slots

Burner

Tube

Injector Holder (May

Be Brass or Aluminum

Depending on Model)

Primary Air Inlet Holes (Shape

of Holes May Vary by Model)

www.desatech.com

113066-01A 17

CABINET

Air Passageways

• Use a vacuum cleaner or pressurized air to

clean.

Exterior

• Use a soft cloth dampened with a mild soap

and water mixture. Wipe the cabinet to remove

dust.

LOGS

• If you remove logs for cleaning, refer to In-

stalling Logs, page 11, to properly replace logs.

• Replace log(s) if broken or chipped (dime-sized

or larger).

MAIN BURNER

Periodically inspect all burner flame holes with

the heater running. All slotted burner flame holes

should be open with yellow flame present. All

round burner flame holes should be open with a

small blue flame present. Some burner flame holes

may become blocked by debris or rust, with no

flame present. If so, turn off heater and let cool.

Remove blockage. Blocked burner flame holes

will create soot.

CLEANING AND

MAINTENANCE

Continued

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specified heat

• propane/LP gas supply may be low

You may feel your gas pressure is too low. If so,

contact your local gas supplier.

TECHNICAL SERVICE

You may have further questions about installation,

operation, or troubleshooting. If so, contact DESA

Heating Products’ Technical Service Department

at 1-866-672-6040. When calling, please have your

model and serial numbers of your heater ready.

You can also visit DESA Heating Products’ tech-

nical services web site at www.desatech.com.

SPECIFICATIONS

CS26PT CS26NT

Btu (Variable) 20,000/26,000 20,000/26,000

Type Gas Propane/LP Natural

Ignition Piezo Piezo

Manifold Pressure 8" W.C. 3.0" W.C.

Inlet Gas Pressure (in. of water) *

Maximum 14" 10.5"

Minimum 11" 5"

Dimensions, Inches (H x W x D)

Stove 25 x 24

/4 x 13

/4 25 x 24

/4 x 13

Weight, pounds

Stove 45 lbs. 45 lbs.

Shipping 55 lbs. 55 lbs.

* For purposes of input adjustment

www.desatech.com 113066-01A

TROUBLESHOOTING

Note:

All troubleshooting items are listed in order of operation.

WARNING: Turn off heater and let cool before servicing. Only a

qualified service person should service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean

ODS/pilot. This can damage ODS/pilot unit.

POSSIBLE CAUSE

1. Ignitor electrode not con-

nected to ignitor cable

2. Ignitor cable pinched or wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned

wrong

1. Gas supply turned off or

equipment shutoff valve

closed

2. Control knob not in PILOT

position

3. Control knob not pressed in

while in PILOT position

4. Air in gas lines when installed

5. Depleted gas supply, propane/

LP only

6. ODS/pilot is clogged

7. Gas regulator setting is not

correct

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched

by any metal or tubing. Keep

ignitor cable dry

3. Tighten nut holding piezo ig-

nitor to base panel of log set.

Nut is located behind base

panel

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace pilot assembly

7. Replace pilot assembly

1. Turn on gas supply or open

equipment shutoff valve

2. Turn control knob to PILOT

position

3. Press in control knob while in

PILOT position

4. Continue holding down con-

trol knob. Repeat igniting op-

eration until air is removed

5. Contact local propane/LP gas

company

6. Clean ODS/pilot (see Cleaning

and Maintenance, page 16) or

replace ODS/pilot assembly

7. Replace gas control

OBSERVED PROBLEM

When ignitor button is pressed,

there is no spark at ODS/pilot

When ignitor button is pressed,

there is spark at ODS/pilot but

no ignition

www.desatech.com

113066-01A 19

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

Control knob not fully pressed in

2. Control knob not pressed in

long enough

3. Equipment shutoff valve not

fully open

4. Pilot flame not touching ther-

mocouple, which allows ther-

mocouple to cool, causing pi-

lot flame to go out. This prob-

lem could be caused by one or

both of the following:

A) Low gas pressure

B) Dirty or partially clogged

ODS/pilot

5. Thermocouple connection

loose at control valve

6. Thermocouple damaged

7. Control valve damaged

1. Burner orifice clogged

2. Inlet gas pressure is too low

3. Thermopile leads discon-

nected or improperly con-

nected

4. Burners will not come on in

remote position

1. Manifold pressure is too low

2. Burner orifice clogged

1. Burner orifice is clogged or

damaged

2. Damaged burner

3. Gas regulator defective

1. Not enough air

2. Gas regulator defective

3. Residues from manufacturing

processes and logs curing

1. Not enough combustion/ven-

tilation air

REMEDY

1. Press in control knob fully

After ODS/pilot lights, keep con-

trol knob pressed in 30 seconds

3. Fully open equipment shutoff

valve

4. A) Contact local gas company

B) Clean ODS/pilot (see

Cleaning and Maintenance,

page 16) or replace ODS/pi-

lot assembly

5. Hand tighten until snug, then

tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

1. Clean burner (see Cleaning and

Maintenance, page 16) or re-

place burner orifice

2. Contact local gas company

3. Reconnect leads (see wiring

diagram)

4. Replace battery in transmitter

and receiver

1. Contact local gas company

2. Clean burner (see Cleaning and

Maintenance, page 16) or re-

place burner orifice

1. Clean burner (see Cleaning and

Maintenance, page 16) or re-

place burner orifice

2. Replace damaged burner

3. Replace gas control

1. Check burner for dirt and de-

bris. If found, clean burner

(see Cleaning and Mainte-

nance, page 16)

2. Replace gas control

3. Problem will stop after a few

hours of operation

1. Refer to Air for Combustion

and Ventilation requirements

(page 5)

OBSERVED PROBLEM

ODS/pilot lights but flame goes

out when control knob is re-

leased

Burner does not light after ODS/

pilot is lit

Delayed ignition burner

Burner backfiring during com-

bustion

Slight smoke or odor during ini-

tial operation

Moisture/condensation noticed

on windows

www.desatech.com 113066-01A

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

1. Turning control knob to HI po-

sition when burner is cold

2. Air in gas line

3. Air passageways on heater

blocked

4. Dirty or partially clogged

burner orifice

1. Improper log placement

2. Drafts or other air currents af-

fecting flame pattern

3. Air holes at burner inlet

blocked

4. Burner flame holes blocked

1. When heated, vapors from fur-

niture polish, wax, carpet

cleaners, etc. may turn into

white powder residue

1. Metal expanding while heating

or contracting while cooling

REMEDY

1. Turn control knob to LO po-

sition and let warm up for a

minute

2. Operate burner until air is re-

moved from line. Have gas line

checked by local gas company

3. Observe minimum installation

clearances (see page 8)

4. Clean burner (see Cleaning and

Maintenance, page 16) or re-

place burner orifice

1. Properly locate logs (see In-

stalling Logs, page 11)

2. Eliminate source of drafts

around heater

3. Clean out air holes at burner

inlet. Periodically repeat as

needed

4. Remove blockage or replace

burner

1. Turn heater off when using

furniture polish, wax, carpet

cleaners, or similar products

1. This is common with most heat-

ers. If noise is excessive, con-

tact qualified service person

OBSERVED PROBLEM

Heater produces a whistling

noise when burner is lit

Dark residue on logs or inside of

fireplace

White powder residue forming

within burner box or on adja-

cent walls or furniture

Heater produces a clicking/tick-

ing noise just after burner is lit

or shut off

Page is loading ...

Comfort Glow CS26PT Owner's manual

Brand: Comfort Glow

Model: CS26PT

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

CS26NT

Download PDF

report

Comfort Glow CS26PT Owner's manual

This manual is also suitable for

Comfort Glow CS26PT Owner's manual

Related papers

Other documents