Indesit KIC 642 C User guide

Page is loading ...

Operating Instructions

Contents

Installation, 24-25

Positioning

Electrical connection

Description of the appliance, 26

Control panel

Start-up and use, 27-30

Switching on the hob

Switching on the cooking zones

Booster function

Switching off the cooking zones

Programming the cooking duration

Timer

Control panel lock

Switching off the hob

Demo mode

Practical advice on using the appliance

Safety devices

Practical cooking advice

Precautions and tips, 31

General safety

Disposal

Care and maintenance, 32

Switching the appliance off

Cleaning the appliance

Disassembling the hob

Technical description of the models, 33

KIA 641 C

KIC 641 X

KIC 642 C

KIC 644 X

KIC 644 DD Z

HOB

Italiano, 1

GB

Espanol, 45

ES

Deutsch, 34

DE

Français, 12 English,23

IT FR

GB

24

GB

Installation

 Before operating your new appliance please read this instruction

booklet carefully. It contains important information concerning the

safe operation, installation and maintenance of the appliance.

 Please keep these operating instructions for future reference.

Pass them on to any new owners of the appliance.

Positioning

 Keep all packaging material out of the reach of children. It may

present a choking or suffocation hazard (see Precautions and

tips).

 The appliance must be installed by a qualified professional in

accordance with the instructions provided. Incorrect installation

may cause harm to people and animals or may damage property.

Built-in appliance

Use a suitable cabinet to ensure that the appliance functions

properly.

The supporting surface must be heat-resistant up to a

temperature of approximately 100°C.

 If the appliance is to be installed above an oven, the oven

must be equipped with a forced ventilation cooling system.

 Avoid installing the hob above a dishwasher: if this cannot be

avoided, place a waterproof separation device between the

two appliances.

 Depending on the hob you want to install, the cabinet must

have the following dimensions (see figure):

560 +/- 1

490 +/- 1

53

590

520

Ve n tilat ion

To allow adequate ventilation and to avoid overheating of the surrounding

surfaces the hob should be positioned as follows:

 At a minimum distance of 40 mm from the back panel or any

other vertical surfaces.

 So that a minimum distance of 20 mm is maintained between

the installation cavity and the cabinet underneath.

 Kitchen cabinets adjacent to the appliance and taller than the

top of the hob must be

at least 600 mm from the edge of the

hob.

Fixin g

The appliance must be installed on a perfectly level supporting

surface.

Any deformities caused by improper fixing could affect the

features and operation of the hob.

FRONT SIDE

OF HOB

SUPPORTING

SURFACE

30

40

UNDERSIDE

OF HOB

5 mm

min. 20 mm

min. 40 mm

COMPARTMENT

5 mm

min. 40 mm

FAN-ASSISTED

OVEN

25

GB

The thickness of the supporting surface should be taken into

account when choosing

the length of the screws for the fixing

hooks:

 30 mm thick: 23 mm screws

 40 mm thick: 13 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment springs in

the holes provided at the central point of each side of the hob.

2. Place the hob in the cavity, make sure it is in a central position

and push down on the whole perimeter until the hob is stuck to

the supporting surface.

3. For hobs with raised sides: After inserting the hob into its

cavity, insert the 4 fixing hooks (each has its own pin) into the

lower edges of the hob, using the long pointed screws to fix them

in place, until the glass is stuck to the supporting surface.

 The screws for the alignment springs must remain accessible.

 In order to adhere to safety standards, the appliance must not

come into contact with electrical parts once it has been installed.

 All parts which ensure the safe operation of the appliance must

not be removable without the aid of a tool.

Electrical connection

 The electrical connection for the hob and for any built-in oven

must be carried out separately, both for safety purposes and to

make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity supply

cable, which is designed for single-phase connection. Connect

the wires in accordance with the instructions given in the

following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

220-240V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

 400V - 2+N ~ 50 Hz

 220-240V 3 ~ 50 Hz

 400V 3 - N ~ 50 Hz

 400V - 2+2N ~ 50 Hz

Separate the wires and connect them in accordance with the

instructions given in the following table and diagrams:

Tensión tipo y

frecuencia de la red

Cable eléctrico Conexión de los cables

400V - 2+N ~

50 Hz

220-240V 3 ~

50Hz

400V 3-N~ 50Hz

: amarillo/verde;

N: los 2 cables azules juntos

L1: negro

L2: marrón

400V - 2+2N ~

50 Hz

: amarillo/verde;

N1: azul

N2: azul

L1: negro

L2: marrón

Connecting the electricity supply cable to the

m a i n s

If the appliance is being connected directly to the electricity

mains an omnipolar switch must be installed with a minimum

opening of 3 mm between contacts.

 The installer must ensure that the correct electrical connection

has been made and that it is fully compliant with safety

regulations.

Before connecting the appliance to the power supply, make sure

that:

The appliance is earthed and the plug is compliant with the

law.

The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located on the

appliance itself.

The voltage falls within the range of values indicated on the

data plate.

The socket is compatible with the plug of the appliance. If the

socket is incompatible with the plug, ask an authorised

technician to replace it. Do not use extension cords or multiple

sockets.

 Once the appliance has been installed, the power supply cable

and the electrical socket must be easily accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced by

authorised technicians only.

 The manufacturer declines any liability should

these safety measures not be observed.

 Do not remove or replace the power supply cable for any

reason. Its removal or replacement will void the warranty and the

CE marking. INDESIT does not assume liability for accidents or

damage arising from replacement/removal of the original power

supply cable. Replacement can only be accepted when carried

out by personnel authorised by INDESIT and using an original

spare part.

26

GB

Description of the

appliance

Control panel

 INCREASE POWER button switches on the

hotplate and controls the power (see Start-up and

use).

 REDUCE POWER button controls the power and

switches off the hotplate (see Start-up and use).

 COOKING ZONE SELECTOR button shows a

particular cooking zone has been selected and

therefore various adjustments are possible.

 COOKING ZONE SELECTOR button is used to

select the desired cooking zone.

 POWER indicator provides a visual display for the

current heat level.

 ON/OFF button switches the appliance on and off.

 ON/OFF indicator light shows whether the

appliance is on or off.

 PROGRAMME TIMER* button controls the

cooking programme times

(see Start-up and use).

 PROGRAMME TIMER* display shows which

programme has been selected (see Start-up and

use).

 COOKING ZONE PROGRAMMED* indicator lights

show which cooking zones are being used during

a cooking programme (see Start-up and use).

 CONTROL PANEL LOCK button prevents

accidental changes to the hob settings (see Start-

up and use).

 CONTROL PANEL LOCK indicator light shows

the control panel has been locked (see Start-up

and use).

 BOOSTER

button* activates the booster function -

3000 W - of the cooking zone (see Start-up and

use).

 BOOSTER indicator light* shows that the booster

function has been activated.

 TIMER* indicator light shows that the timer has

been activated

The control panel described in this manual is only a representative example: it may not exactly match the panel

on your appliance.

BOOSTER*

button

BOOSTER*

indicator light

Booster

ON/OFF

indicator light

CONTROLS LOCKED

indicator light

CONTROL PANEL

LOCK button

INCREASE

POWER button

COOKING ZONE PROGRAMMED*

indicator light

PROGRAMME TIMER*

display

PROGRAMME

TIMER* button

COOKING ZONE

SELECTOR buttons

REDUCE POWER

button

COOKING ZONE

SELECTED indicator light

POWER and

RESIDUAL HEAT

indicators

ON/OFF

button

TIMER*

indicator light

*

Only available in certain models.

27

GB

Start-up and use

 The glue applied on the gaskets leaves traces of grease on the

glass. Before using the appliance, we recommend you remove

these with a special non-abrasive cleaning product. During the

first few hours of use there may be a smell of rubber which will

disappear very quickly.

 A few seconds after the hob is connected to the electricity

supply, a buzzer will sound. The hob may now be switched on.

Types of noise during normal hob operation:

 Buzz: due to the vibration of the metallic parts that make up

the induction element and the pot; it is generated by the

electromagnetic field required for heating and increases as

the power of the induction element increases.

 Soft whistle: heard when the pot placed on the heating

zone is empty; the noise disappears once food or water is

placed into the pot.

 Crackle: produced by the vibration of materials on the bottom

of the pot due to the flow of parasitic currents caused by

electromagnetic fields (induction); can be more or less intense

depending on the material making up the bottom of the pot,

and decreases as the pot dimensions increase.



Loud whistle: heard when two induction elements of the

same group function simultaneously at maximum power and/or

when the booster function is set on the larger element while

the other is auto-adjusted. Noise is reduced by decreasing the

power level of the auto-adjusted induction element; pot bottom

layers made of different kinds of materials are among the main

causes of this noise.

 Fan noise: a fan is necessary to ensure the hob functions

correctly and to safeguard the electronic unit from possible

overheating. The fan functions at maximum power when the

large induction element is at maximum power or when the

booster function is on; in all other cases, it works at average

power depending on the temperature detected. Furthermore,

the fan may continue to work even after switching the hob off,

if the temperature detected is high.

The types of noise listed above are due to induction technology

and are not necessarily operational faults.

 If the - or + button is pressed for an extended period of time,

the display scrolls quickly though the power levels and timer

minutes.

Switching on the hob

To switch the hob on, press and hold the button for

approximately one second.

Switching on the cooking zones

Each cooking zone is controlled using a selector button and

a power adjustment device consisting of a double

- and +

button.

To begin operating a cooking zone, press the corresponding

control button and set the desired power level (between 0 and

9) using the buttons

- and +.

Booster function*

The booster function for some of the cooking zones may be used to

shorten heating-up times. It may be activated by pressing the

Booster

button. The indicator light directly above the button will illuminate. This

function boosts the power to 2000 W or 3000 W, depending on the

size of the relevant cooking zone.

The booster stops automatically after 4 minutes. While the booster for

one of the cooking zones is active, the corresponding front or rear

cooking zone will operate at a reduced power level (e.g. if the booster

for the rear left-hand hotplate has been activated, the power level of

the front left-hand hotplate will be reduced). For further information,

please refer to the Technical description of the models.

Switching off the cooking zones

To switch off a cooking zone, select it using the corresponding

selector button

and:

 Press the

- button: the power of the cooking zone will

progressively decrease until it is switched off.

Programming the cooking duration

 All the cooking zones may be programmed simultaneously, for a

duration between 1 and 99 minutes.

1. Select the cooking zone using the corresponding selector

button.

2. Adjust the temperature.

3. Press the

programming button.

4. Set the cooking duration using the

- and + buttons.

5. Confirm by pressing the

button.

The timer begins counting down immediately. A buzzer sounds for

approximately 1 minute and the cooking zone switches off when

the set programme has finished.

Repeat the above procedure for each hotplate you wish to

programme.

*

Only available in certain models.

28

GB

Using multiple programmes and the display

If one or more hotplates are programmed, the display will show

the data for the hotplate with the least time remaining, and the

light corresponding to the position of the hotplate will flash. The

lights corresponding to the other hotplates programmed will be

switched on.

To display the time remaining for the other programmed hotplates,

press the

button repeatedly. The times remaining for each

hotplate will be shown in a clockwise order, beginning with the

front left hotplate.

Changing the programme

1. Press the

button repeatedly until the duration you wish to

change is shown.

2. Use the

buttons to set the new duration.

3. Confirm by pressing the

button.

To cancel a programme, follow the above instructions. At step 2,

press the

- button: the duration decreases progressively until it

reaches 0 and switches off. The programme resets and the

display exits programming mode.

Timer

The hob must be switched on.

The timer can be used to set a duration up to 99 minutes.

1. Press the

programming button until the timer indicator

light is illuminated.

2. Set the desired duration using the

- and + buttons.

3. Confirm by pressing the

button.

The timer begins counting down immediately. When the time has

elapsed, a buzzer will sound (for one minute).

Control panel lock

When the hob is switched on, it is possible to lock the oven

controls in order to avoid accidental changes being made to the

settings (by children, during cleaning, etc.). Press the

button to lock the control panel: the indicator light above the

button will switch on.

To use any of the controls (e.g. to stop cooking), you must switch

off this function. Press the

button for a few moments, the

indicator light will switch off and the lock function will be removed.

Switching off the hob

Press the button to switch the appliance off.

If the control panel lock has been activated, the controls will

continue to be locked even after the hob is switched on again. In

order to switch the hob on again, you must first remove the lock

function.

Demo mode

It is possible to set the hob to a demonstration mode where all

the controls work normally but the heating elements do not switch

on. To activate the demo mode the hob must be switched on,

with all the hotplates switched off.

 Press and hold the

+ and - buttons simultaneously for 6

seconds. When the 6 seconds have elapsed, the ON/OFF and

CONTROLS LOCKED indicator lights will flash for one second.

Release the

+ and - buttons and press the button;

The display will show the text DE and MO and the hob will be

switched off.

 When the hob is switched on again it will be set to the demo

mode.

To exit this mode, follow the procedure described above. The

display will show the text DE and OF and the hob will be switched

off. When it is next switched on, the hob will function normally.

Practical advice on using the appliance

 Use cookware made from materials which are compatible with

the induction principle (ferromagnetic material). We especially

recommend pans made from: cast iron, coated steel or special

stainless steel adapted for induction. Use a magnet to test the

compatibility of the cookware.

*

SUITABLE

UNSUITABLE

Cast iron

Enamelled steel

Special stainless steel

Copper,

Aluminium, Glass, Earthenware,

Ceramic, non magnetic Stainless steel

In addition, to obtain the best results from your hob:

Use pans with a thick, flat base in order to fully utilise the

cooking zone.

 Always use pans with a diameter which is large enough to cover

the hotplate fully, in order to use all the available heat.

29

GB

 Make sure that the base of the cookware is always clean and

dry, in order to fully utilise and extend the life of both the

cooking zones and the cookware.

 Avoid using the same cookware which has been used on gas

burners: the heat concentration on gas burners may distort

the base of the pan, causing it not to adhere correctly.

Safety devices

Pan sensor

Each cooking zone is equipped with a pan sensor device. The

hotplate only emits heat when a pan with suitable measurements

for the cooking zone is placed on it. If the indicator light is

flashing, it may indicate:

 An incompatible pan

 A pan whose diameter is too small

The pan has been removed from the hotplate.

Overheating protection

If the electronic elements overheat, the hob switches off

automatically and

F appears on the display, followed by a

flashing number. When the temperature has reached a suitable

level, this message disappears and the hob may be used again.

Safety switch

The appliance has a safety switch which automatically switches

the cooking zones off after they have been in operation for a

certain amount of time at a particular power level. When the

safety switch has been triggered, the display shows 0.

For example: the right rear hotplate is set to 5 and will switch off

after 5 hours of continuous operation, while the front left hotplate

is set to 2 and will switch off after 8 hours.

Power level

Maximum operating

time in hours

1 9

28

37

46

55

64

73

82

9 1

B u zze r

This can also indicate several irregularities:

 An object (a pan, cutlery, etc.) has been placed on the

control panel for more than 10 seconds.

 Something has been spilt on the control panel.

 A button has been pressed for too long. All of the above

situations may cause the buzzer to sound. Remove the cause

of the malfunction to stop the buzzer. If the cause of the

problem is not removed, the buzzer will keep sounding and the

hob will switch off.

30

GB

Practical cooking advice

ª

Pressure cooking

Pressure cooker

Frying

Very high-flame

cooking



Grilling Boiling



High-flame

cooking

¶

Crêpes Cooking on a high flame and browning

(roasts, steaks, escalopes, fish fillets,

fried eggs)

¶

§

Fast thickening (liquid juices)

Boiling water (pasta, rice, vegetables)

Milk

§

S

Slow thickening (dense juices)

S

Medium-flame cooking

¢

Bain-marie cooking Pressure cooking after whistle

¢

£

Low-flame

cooking



Low-flame cooking

(stews)

-{}-

Reheating dishes



Very low-

flame

cooking

¡

Chocolate sauce Keeping food hot

31

GB

Precautions and tips

 This appliance has been designed and manufactured in

compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

This appliance conforms to the following European

Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low Voltage) and

subsequent amendments;

-89/336/EEC dated 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent amendments.

General safety

 Make sure that the air inlet behind the fan grille is never

obstructed. The built-in hob should, in fact, be provided

with suitable ventilation for the cooling of the electronic

components used in the appliance.

 We advise against the installation of an induction hob

above an under-the-counter refrigerator (heat) or above a

washing machine (vibrations). In fact, there would be

insufficient space for the ventilation of electronic

components.

The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial

use.

The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

 Do not touch the appliance when barefoot or with wet

or damp hands and feet.

The appliance must be used by adults only for the

preparation of food, in accordance with the instructions

provided in this booklet. Do not use the hob as a

worktop or chopping board.

The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with a

sharp object such as a tool. If this happens,

disconnect the appliance from the electricity mains

immediately and contact a Service Centre.

 Ensure that power supply cables of other electrical

appliances do not come into contact with the hot parts

of the hob.

 Remember that the cooking zones remain relatively hot

for at least thirty minutes af

ter they have been switched

off. An indicator light provides a warning when residual

heat is present (see Start-up and use).

 Keep any object which could melt away from the hob,

for example plastic and aluminium objects, or products

with a high sugar content. Be especially careful when

using plastic film and aluminium foil or packaging: if

placed on surfaces which are still hot, they may cause

serious damage to the hob.

 Always make sure that pan handles are turned towards

the centre of the hob in order to avoid accidental

burns.

 When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

The appliance should not be operated by people

(including children) with reduced physical, sensory or

mental capacities, by inexperienced individuals or by

anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by

someone who assumes responsibility for their safety or

receive preliminary instructions relating to the operation

of the appliance.

 For the attention of wearers of pacemakers or

other active implants:

The hob complies with all current standards on

electromagnetic interference.

Your induction hob is therefore perf

ectly in keeping with

legal requirements (89/336/CEE directives). It is

designed not to create interference on any other

electrical apparatus being used on condition that the

apparatus in question also complies with this

legislation.

Your induction hob generates short-range magnetic

fields.

To avoid any interference between your induction hob

and a pacemaker, the latter must be designed to

comply with relevant regulations.

In this respect, we can only guarantee our own product

conformity. Please consult the pacemaker manufacturer

or your doctor concerning its conformity or any possible

incompatibility.

 Do not let children play with the appliance.

Disposal

 When disposing of packaging material: observe local

legislation so that the packaging may be reused.

The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-

out dustbin is marked on all products to remind the

owner of their obligations regarding separated waste

collection.

For further information relating to the correct disposal of

exhausted household appliances, owners may contact

the public service provided or their local dealer.

32

GB

Care and maintenance

Switching the appliance off

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Cleaning the appliance

 Do not use abrasive or corrosive detergents (for

example, products in spray cans for cleaning

barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with

abrasive surfaces: these may scratch the surface

beyond repair.

 Never use steam cleaners or pressure cleaners on

the appliance.

 It is usually sufficient simply to wash the hob

using a damp sponge and dry it with absorbent

kitchen towel.

 If the hob is particularly dirty, rub it with a special

glass ceramic cleaning product, then rinse well

and dry thoroughly.

To remove more stubborn dirt, use a suitable

scraper. Remove spills as soon as possible,

without waiting for the appliance to cool, to avoid

residues forming crusty deposits. You can

achieve excellent results by using a rust-proof

steel wire sponge - specifically designed for

glass ceramic surfaces - soaked in soapy water.

 If any plastic or sugary substances are

accidentally melted on the hob, remove them

immediately with the scraper, while the surface is

still hot.

 Once it is clean, the hob may be treated with a

special protective maintenance product: the

invisible film left by this product protects the

surface from drips during cooking. This

maintenance task should be carried out while the

appliance is warm (not hot) or cold.

 Always remember to rinse the appliance well with

clean water and dry it thoroughly: residues can

become encrusted during subsequent cooking

processes.

Stainl

ess steel frame (only in models with outer

frame)

Stainless steel can be marked by hard water which

has been left on the surface for a long time, or by

cleaning products containing phosphorus.

After cleaning, it is advisable to rinse the surface

well and dry it thoroughly. If water is spilt on the

surface, dry it quickly and thoroughly.

 Some hobs have an aluminium frame which is

similar to stainless steel. Do not use any cleaning or

degreasing products which are not suitable for use

with aluminium.

Disassembling the hob

If it is necessary to disassemble the hob:

1. Loosen the screws fixing the alignment springs on

each side.

2. Loosen the screws holding the fixing hooks in

each corner.

3. Take the hob out of its installation cavity.

 Do not attempt to repair the appliance yourself. If

the appliance breaks down, contact a Service

Centre.

33

GB

Technical description of

the models

The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking

zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic

bases.

Hobs

KIA 641 C KIC 644 DD Z KIC 641 X

Cooking zone

Power (W)

Back Left

I 1400 I 1400  B 2000*  600 if Front Left* I 1400

Back Right

I 2200  B 3000* I 2200  B 3000* - 1600 if Front Right* I 2200  B 3000*

Front Left

I 2200 I 2200  B 3000* - 1600 if Back Left* I 2200

Front Right

I 1400  600 if Back Right* I 1400  B 2000*  600 if Back Right* I 1400  600 if Back Right*

Total power

7200 7200 7200

Hobs

KIC 642 C KIC 644 X

Cooking zone

Power (W)

Back Left

I 1400  600 if Front Left* I 1400  B 2000*  600 if Front Left*

Back Right

I 2200  B 3000* I 2200  B 3000* - 1600 if Front Right*

Front Left

I 2200  B 3000* I 2200  B 3000* - 1600 if Back Left*

Front Right

I 1400  600 if Back Right* I 1400  B 2000*  600 if Back Right*

Total power

7200 7200

Key:

I = single induction cooking zone

B = booster: the power level of the cooking zone may be boosted to 3000 W

* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see

Start-up and use).

Page is loading ...

Indesit KIC 642 C User guide

This manual is also suitable for

Indesit KIC 642 C User guide

in other languages

Related papers

Other documents