DO NOT RETURN TO THE STORE !
Visit www.dhpfurniture.com/eng/support-home
or call Toll-Free 1-800-267-1739
4124019
B34412401900 - 10125-M
Date of Purchase
Maven Platform Bed With Storage
N.C. - 4/3/2017
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
© 2014 Dorel Home Products All Rights Reserved
Twin
Black Faux Leather
Weight Limit: 225 Lb / 102 Kg
TM
Contact Us!
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec, Canada H1G 3L1
Read Before Beginning Assembly
1-800-267-1739
Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)
Warranty Information
2
B34412401900
Caution
DHP warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers one year from the date of
original purchase. This is solely limited to the repair or replacement of defective
parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way.
Liability for consequential damages is excluded to the extent exclusion is permitted
by law. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
To obtain warranty service, purchaser must present original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty
period only. The defective components will be repaired or replaced without charge,
subject to the terms and conditions described above.
Visit www.dhpfurniture.com
to view the limited warranty valid in the U.S. and
Canada.
● Call our toll free number if you need assistance.
● Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
● Recommended # of people needed for assembly: 2 (however it is always better
to have an extra hand). Estimated assembly time is 1.5 hours.
● Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
● Read each step carefully. It is very important that each step of instruction is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
● This product is designed for home use and not intended for commercial use.
● This product contains small components. Please ensure that they are kept away
from small children.
● Do not use power tools to assemble your furniture. Power tools may strip or
damage the parts.
● You will need a phillips headed screwdriver to assemble this product.
For help with assembly, identifying parts, product information or to order parts,
please contact us:
Page is loading ...
4
Parts
B34412401900
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
A
Headboard
T946240
X 1
B
C
D
E
F
G
H
Footboard
T946250
X 1
Side Panel
T946260
X 1
Side Panel
T946270
X 1
Side Rail
T946280
X 1
Side Rail
T946290
X 2
Center Rail
T946300
X 2
Support Rail
T946310
X 1
I
Guide
T946320
X 1
O
Wooden Slat
T926760
X 24
R
Cross Brace
T946340
X 1
X
Single Slat Cap
T926370
X 24
Y
Double Slat Cap
T926380
X 12
Z
Leg
T946370
X 2
A
B
D
C
E
G
F
M
Support Leg
T946330
X 1
R
H
O
I
U
Side Panel
T946350
X 1
V
U
V
Side Rail
T946360
X 1
M
Z
X
Y
5
Parts
B34412401900
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
J
Front Panel
T946380
X 1
K
Drawer Bottom Panel
T946390
X 1
L
Drawer Back Panel
T946400
X 1
N
Drawer Side Panel
T946410
X 2
S
Drawer Front Panel
T946420
X 1
Q
Caster
T946430
X 4
J
K
L
N
S
Q
6
Hardware Pack
B34412401900
Hardware Pack #: T4124019-00
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of
the page.
6 7 8
4
5
3
2
1
1/4" X 3/4"
X 1
9
1/4" X 3/4"
X 13
1/4" X 1 3/16"
X 3
1/4" X 1 9/16"
X 6
6# X 1/2"
X 8
1/4"
X 4
4mm
X 1
1/4" X 1 9/16"
X 21
4# X 1 3/16"
X 20
7
B34412401900
Step
1
Attach Z X 2 and F X 2 to C and D with .
X 10
5
5
5
5
Z
C
F
C
D
Z
Z
F
F
Note: Holes on part F should be facing upward
D
8
B34412401900
Step
2
X 5
5
5
5
C
U
V
Note: You have two choices for the drawer
location as illustrated.
If you intend to place the drawer in the 1st
location, then: Attach V to U and C with .
If you intend to place the drawer in the 2nd
location, then: Attach V to U and D with .
D
U
V
5
1st choice for Drawer location
2nd choice for Drawer location
C
U
D
U
5
9
B34412401900
Step
3
1st choice for drawer location:
Attach E to D with .
2nd choice for drawer location:
Attach E to C with .
X 2
5
5
5
E
D
C
E
1st choice for Drawer location
2nd choice for Drawer location
5
5
10
B34412401900
Step
4
Attach I to B with .
X 2
4
4
4
I
B
11
B34412401900
Step
5
5.1 Attach Z X 2 to A with .
5.2 Attach E and V to B with .
X 4
5
A
C
Z
B
V
U
4
5
4
X 4
5
A
B
C
D
E
U
V
4
B
A
D
E
U
C
1st choice for Drawer location
2nd choice for Drawer location
Z
Z
V
5.1
5.2
12
B34412401900
Step
6
Insert Gx2 into M with .
X 2
2
2
G
G
M
2
G
G
M
13
B34412401900
Step
7
Attach Gx2 to A and B with .
Note: We will continue to show the
assembly with the drawer placed in 1st
location. If you intent to assemble the
drawer in the 2nd location please follow the
same steps.
X 4
2
2
2
G
A
G
G
A
B
14
B34412401900
Step
8
Attach H to C and D with .
X 4
2
2
Note: small tubes on part H should be orientated as illustrated,
facing toward B.
C
D
H
U
H
C
U
B
15
B34412401900
Step
9
Attach R to E, G and V with .
2
X 3
2
R
V
V
R
G
E
2
Note: arched side on R must be facing upward.
16
B34412401900
Step
10
10.1 Insert O into X;
10.2 Press X into E, V and F, repeat the
same procedure for the opposite side.
10.3 Insert ends of both slats O into Y,
then press Y into G as illustrated.
Repeat the same procedures going
backwards for every row of slats.
10.1
10.2
10.3
O
X
X
F
G
Y
O
O
Y
O
X
G
F
V
E
F
O
17
B34412401900
Step
11
L
S
N
N
Attach Nx2 to S and L with .
7
X 8
7
Note: For a better looking and for ease of assembly, orientate ALL PANELS with the staples and
pilot holes facing toward the outside and on upper side.
Note: before assembling, line up
the screws and holes on N with pilot
holes on S and L.
18
B34412401900
Step
12
K
L
N
Attach K to S , L and N with .
7
7
X 12
S
N
Note: before assembling, line up
the screws and holes on K with pilot
holes on N, S and L.
Note: For a better looking, orientate
the staples toward the outside.
19
B34412401900
Step
13
Q
K
Attach Qx4 to K with .
6
Q
K
X 8
6
Note: before assembling, line up
screws and holes on Q with pilot
holes on K.
20
B34412401900
Step
14
J
S
S
J
Turn over sub-assembly from previous step
and:
14.1 Attach and to J where indicated;
14.2 Attach sub-assembly N, L and S to J
with and .
3
8
3
8
X 4
X 3
3
8
1
8
X 1
1
J
1
8
14.1
14.2
21
B34412401900
Step
15
Align the drawer and then push it in.
Lock drawer by slightly lifting drawer and
inserting the Pin into the Slot.
1st choice for Drawer location
2nd choice for Drawer location
Slot
Pin
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
