Aga Ranges SIX-FOUR SERIES - DC6 User manual

AGA SIX-FOUR SERIES - DC6 (FFD)

(NATURAL GAS AND PROPANE GAS)

OWNERS MANUAL

03/08 EINS 514735

PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS APPLIANCE

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE

CUSTOMER: KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Remember, when replacing a part on this appliance, use only spare parts that you can be

assured conform to the safety and performance specification that we require. Do not use

reconditioned or copy parts that have not been clearly authorised by AGA.

Comprising

Servicing, Installation & Users

Instructions

&

Cooking Guide

For use in USA/Canada

Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT DO YOU DO IF YOU SMELL GAS

. Do not try to light any appliance.

. Do not touch any electrical switch

. Do not use any phone in your building.

. Immediately call your gas supplier from a neighbors phone.

Follow the gas suppliers instructions

. If you can not reach your gas supplier call the fire department.

Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

WARNING: If the information in this manual is not followed exactly, a fire or

explosion may result causing property damage,personal injury or death.

SECTION PAGE

INSTALLATION SECTION 3

TECHNICAL DATA 4

INSTALLATION 5

FITTING AND PRODUCT DIMENSIONS 6

ELECTRICAL CONNECTION 7 - 8

CONNECTING TO GAS 9

LOCATION 10

COOKER STABILITY 11 - 12

PRESSURE TESTING 12

LEVELLING AND MOBILITY WHEELS 13

FITTING OF HOTPLATE CASTINGS AND PAN 14 - 17

SUPPORTS

SPLASHBACK 18

USERS GUIDE 19

GENERAL INFORMATION 20

SAFETY PRECAUTIONS AND HINTS 21

PRODUCT VIEW 22

CONTROL PANEL 23

GAS HOTPLATE 24 - 25

TO FIT PAN SUPPORTS 26

SETTING UP THE COOKER FOR USE 27

SIMMERING OVEN 28

SIMMERING OVEN RECIPES 29 - 32

THE BROILER 33

THE OVENS 34

OVEN COOKING GUIDE 35 - 39

THE MINUTE TIMER 40

AUTOMATIC COOKING CONTROL 41 - 42

CLEANING AND CARING FOR YOUR COOKER 42 - 48

SERVICING SECTION 49

SERVICING 50 - 58

2

CONTENTS

Installation

Section

3

Remember, when replacing a part on this appliance, use only spare parts that you can be

assured conform to the safety and performance specification that we require. Do not use

reconditioned or copy parts that have not been clearly authorised by AGA.

CAUTION:

THIS UNIT IS HEAVY, PROPER EQUIPMENT AND ADEQUATE

MANPOWER MUST BE USED IN MOVING THE RANGE TO

AVOID DAMAGE TO THE UNIT OR THE FLOOR

HOTPLATE

NATURAL GAS

L.H.F. R.H.F. R.H.R. L.H.R. CENTRE CENTRE

WOK FRONT REAR

BURNER TYPE ULTRA-RAPID RAPID RAPID SEMI-RAPID SEMI-RAPID ULTRA-RAPID

MAXIMUM HEAT 4.5 kW 3.22 kW 3.22 kW 1.91 kW 1.91 kW 5.1 kW

INPUT

BTU’s/hr 15,350 11,000 11,000 6,500 6,500 17,400

INJECTOR MARKING

MAIN 80Hi 155 155 118 118 200

SECONDARY 2 x 1.30 - - - - -

PRESSURE POINT POSITION:REAR RH SIDE OF HOTPLATE

PRESSURE SETTING: 4” W.G.

BURNER IGNITION: H.T. SPARK

PROPANE

L.H.F. R.H.F. R.H.R. L.H.R. CENTRE CENTRE

WOK FRONT REAR

BURNER TYPE ULTRA-RAPID RAPID RAPID SEMI-RAPID SEMI-RAPID ULTRA-RAPID

MAXIMUM HEAT 4.2 kW 3.0 kW 3.0 kW 1.75 kW 1.75 kW 4.5 kW

INPUT

BTU’s/hr 14,330 10,250 10,250 6000 6000 15,350

INJECTOR MARKING

MAIN 46 85 85 65 65 110

SECONDARY 2 x 66 - - - - -

PRESSURE POINT POSITION:REAR RH SIDE OF HOTPLATE

PRESSURE SETTING: 10” W.G.

BURNER IGNITION: H.T. SPARK

ELECTRIC GRILL AND OVENS WEIGHT OF APPLIANCE: 220 kg

TOP OVEN POWER RATING - 1.45 kW

BROILER ELEMENT - POWER RATING 2.45 kW

SLOW COOKING OVEN - POWER RATING 1.0 kW

LOWER OVEN (FAN) - 2.2 kW

240 VOLT 60 Hz SINGLE PHASE

The data plaque is located on a pull out plate - lower front of appliance (See Fig. 10, Page 22).

TYPICAL SECTION VIEW OF FLAMES:

TECHNICAL DATA

4

15/16”

9/16”

7/8”

1/2”

3/4”

9/16”

LHF HOTPLATE BURNER

CR HOTPLATE BURNER

RHF & RHR HOTPLATE

BURNER

LHR & CF HOTPLATE BURNER

CAUTION: THIS INSTALLATION MUST CONFORM WITH LOCAL CODES OR, IN THE

ABSENCE OF LOCAL CODES WITH THE NATIONAL FUEL GAS CODE, ANSI Z223.I/NFPA

54 AND NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (IN CANADA CAN/CGA-B149) AND

ONLY USED IN A WELL VENTILATED SPACE, READ THESE INSTRUCTIONS BEFORE

INSTALLING OR USING THIS APPLIANCE.

PRIOR TO INSTALLATION, ENSURE THAT THE LOCAL DISTRIBUTION CONDITIONS

(NATURE OF GAS AND GAS PRESSURE) AND THE ADJUSTMENTS OF THE APPLIANCE

ARE COMPATIBLE.

THE GAS ADJUSTMENT CONDITIONS FOR THIS APPLIANCE ARE STATED ON THE DATA

PLATE WHICH IS SITUATED IN THE CENTRE VENT SLOT NEAR THE BASE OF THE

FRONT PLATE.

This appliance is not connected to a combustion products evacuation device. it shall be installed

and connected in accordance with current installation regulations. Particular attention shall be

given to the relevant requirements regarding ventilation.

It should be in accordance with any relevant requirements of the Gas Region and Local Authority.

The appliance must be disconnected from the gas supply piping system during any pressure

testing of that system test pressure in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its individual

manual shut off valve during any pressure testing of the gas supply system at test pressures

equal to or less than 1/2 psi (3.5 kPa).

On completion, test the gas installation for soundness and purge. Leak testing of the appliance

shall be conducted according to the manufacturer’s instructions.

NOTE: Use soapy water solution on new gas connections to ensure there are no gas leaks.

WARNING: ELECTRIC SHOCK HAZARD

It is the customers responsibility to contact a qualified electrical installer to make sure the

electrical installation is adequate and in conformance with National Electrical Code ANSI/FPA

70-latest edition, and all local codes and ordinances.

Take special care when cutting holes in walls or floor. Electrical wires may be behind the wall or

floor covering and could cause an electrical shock if you touch them.

Locate any electrical circuits that could be affected by the installation of this product and

disconnect power circuit.

Electrical ground is required on this appliance.

Do not have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit

could result in electrical shock.

Do not use an extension cord with this appliance.

Check with a qualified electrician if you are not sure the appliance is properly grounded.

Failure to follow these instructions could result in death or serious injury.

INSTALLATION

5

FITTING AND PRODUCT DIMENSIONS

6

Fig. 1

DESN 512636 C

Any side wall above the cooker on either side shall be not less than 3” (75mm) horizontally from

the cooker (Fig. 1).

Combustible surfaces over the top of the cooker must not be closer than 28” (711mm) and must

not exceed 13” (400mm) in depth.

0” clearance to the back of the stove may be obtained when installing the appliance against a

non-combustible wall or if the wall behind the stove is deemed combustible, then the minimum

spacing from the back of the stove to nearest combustible wall is 6”.

A minimum clearance of 39

1

/2” (1000mm) must be available at the front of the cooker to enable

it to be serviced.

Any opening in the wall behind the appliance and in the floor under the appliance shall be sealed.

The cooker must stand on a firm and level surface, we recommend that any soft material such

as linoleum is removed.

The vent slots in the back of the top plate must not be obstructed.

Electric Shock Hazard

Electrical Grounding is required on this appliance.

Do Not connect to the electrical supply until the appliance is permanently grounded.

Disconnect the power to the junction box before making the electrical connection.

This appliance must be connected to a grounded, metallic, permanent supply or a

grounding connector should be connected to the grounding terminal or wire lead on the

appliance.

Do Not ground to gas pipe. Failure to follow these instructions could result in death or

serious injury.

z

A four-wire single phase 240-volt, 60-Hz, AC-only electrical supply is required on a

separate circuit, fused on both sides of the line.

z

A time-delay fuse or circuit breaker is recommended.

z

If local codes permit, use a U.L. listed, 250-volt, 30-amperes power cord (pigtail). This cord

contains four No. 10 copper wires and matches a four-wire receptacle of type 14-30R.

Connectors on the appliance end must be provided at the point the power supply enters

the appliance.

Wires sizes (COPPER WIRE ONLY) and connections must conform with the rating of range

(30-amperes).

z

The wiring diagram is located on the back of the appliance.

THIS APPLIANCE MUST HAVE THE FACILITY OF BEING COMPLETELY ISOLATED

FROM THE ELECTRICITY SUPPLY.

THE APPLIANCE MUST

BE COMPLETELY ISOLATED FROM THE ELECTRICITY

SUPPLY BEFORE SERVICING.

7

ELECTRICAL CONNECTION

ELECTRICAL CONNECTION IS LOCATED AT THE TOP RIGHT HAND SIDE OF THE

APPLIANCE, BEHIND SIDE PANEL. DURING INSTALLATION REMOVE THE RIGHT HAND

SIDE PANEL TO CONNECT ELECTRICAL SUPPLY.

Remove 6 screws securing side panel to gain access to mains terminal. See Fig. 3 for location

of cover.

Remember

that the mains electrical cable must be routed through the grommet at the rear right

hand side of the cooker near the top via a UL listed strain relief bracket, before connecting to the

mains terminal connection.

REFER TO FIG. 2 & 2A for wire connection to appliance.

Remember

that an excess of cable length is required inside the cooker to allow for possible

servicing of the spark generator, there should be at least 31” (0.78m) of cable from the appliance.

Remember

that an excess of cable length is required behind the cooker for the withdrawal of the

cooker from between the kitchen units etc.

Replace the right hand side panel once electrical connection has been made and replace fixing

screws.

NOTE: Ensure the insulation card covering the mains terminal is in place, between the side

panel and mains terminal.

ELECTRICAL CONNECTION (continued)

Fig. 2

Fig. 2A

DESN 514739

DESN 512951

8

WIRING DIAGRAM 59

CAUTION: ENSURE THAT THE COOKER IS ISOLATED FROM ELECTRIC SUPPLY

The cooker can be installed with an approved flexible connection. Supply piping should not be

less than 3/8 I/D Flexiline. Connection is made to the 1/2” NPT female thread located just below

the hotplate level on the right hand side of the cooker.

The gas flexiline connector must be fitted in the shaded area dimensioned in Fig. 3. Take into

account that it must be possible to pull the cooker forward sufficiently for servicing. Ensure

flexiline hose is not trapped between cooker back panel and rear wall. Ensure hose is routed

within the shaded area and away from shielded oven vents.

NOTE: Use soapy water solution on new gas connections to ensure there are no gas leaks.

NOTE: AN EASILY ACCESSIBLE MANUAL SHUT GAS VALVE MUST BE FITTED BEFORE

THE METAL FLEX GAS LINE.

Check for gas soundness after connecting the appliance.

9

CONNECTING TO GAS

Fig. 3 DESN 512639 B

This appliance must be installed on 1/8” thick Commercial Grade Vinyl composition floor finishing

materials or equivalent.

Combustible side wall clearance above the hotplate shall be greater than 3”.

Surfaces over the top of the range must not be closer than 28” and must not exceed 13” in depth.

The vent slots in the back of the top plate (or shroud) must not be obstructed.

Note: It is essential that the supply cable is routed away from any hot surfaces i.e. hot flue pipes.

In the interests of safety, due consideration must be given to the protection of the electric cable

to the unit.

Remember than an excess of cable length is required for the possible withdrawal of the range.

A electrical socket type 14-30R must be provided within 5 feet of the left hand side of the range

and be accessible for disconnection.

THE INSTALLATION MUST CONFORM WITH THE NATIONAL ELECTRIC CODE.

Disconnect the electrical supply before servicing the appliance. Electrical hook-up must be done

by a licenced electrician.

An easily accessible manual shut off gas valve must be fitted before the metal flexi gas line

supply to the range. DO NOT fit valve behind the range.

Any opening in the wall behind the appliance and in the floor under the appliance must be

sealed.

If the range must be installed beside a refrigerator, it is important for proper air circulation that

there be at least 5” (175mm) of space between the two appliances.

LOCATION

10

A stability bracket shall be secured firmly to the fabric of the building. For positioning of bracket

(See Fig. 3). A safety chain should also be anchored firmly to the wall and cooker to prevent

strain on the gas connection, when the cooker is withdrawn for servicing. When fitting a stability

bracket and chain refer to Fig. 3, 3A and 3B.

Ranges must have an anti-tip bracket correctly installed as per these instructions. If you pull the

range out from the wall for any reason, make sure that the device is properly engaged when you

push the range back against the wall. If it is not, there is a possible risk of the range tipping over

and causing injury if you or a child stand, sit or lean on an open door.

If disconnection of the restraining chain is necessary then ensure restraining chain is reattached

as appliance is relocated in its original position.

To reduce the risk of tipping, the range must be secured by a properly installed anti-tip bracket

supplied with the range. The bracket must be fitted within the shaded area shown in the diagram

using 2 x screws (No. 10 x 1 1/4”) fixed in the wall or floor, longer screws may be required

depending on the wall or floor covering.

Fig. 3A

Fig. 3B

DESN 512638

11

COOKER STABILITY

CENTRE LINE OF

COOKER

BRACKET

FLOOR

WALL

SIDE VIEW

The maximum gas inlet pressure to the appliance must not exceed 10” w.g. for NG and 14” for

L.P. Gas. The minimum gas inlet pressure at the appliance must not be less than 5” w.g. Natural

Gas and 11” w.g. L.P. Gas to enable the correct manifold pressure to be obtained.

NOTE: The regulator is pre-set for either N.G. or L.P. Gas.

Use the small hotplate burner injector as the pressure test point.

For Natural Gas manifold pressure is 4” w.g.

For L.P.G. (Propane Only) manifold pressure 10” w.g.

Access to the gas regulator is as follows:

a) Remove pan supports and all control knobs.

b) Remove four chrome buttons and the four plate retaining screws (2 each side).

c) Remove left hand and centre shroud from the control panel to gain access to the fixing

screws. Remove two screws from control panel (one from left hand hole and one from

centre hole). (See Fig. 3).

d) Pull top plate forwards slightly and lift up at front. Support top plate and disconnect wiring

to the two neons. Remove top plate.

e) Lay the top plate on its top face, suitably protected.

12

PRESSURE TESTING

POSITION OF GAS VALVE ON WALL (locate in shaded areas)

IMPORTANT: THE GAS SUPPLY CONNECTION AT THE WALL MUST NOT PROJECT

OUT FROM THE WALL BY MORE THAN 1

3

/4” (44mm), SO THAT IT DOES NOT

INTERFERE WITH THE BACK OF THE COOKER.

Fig. 4 DESN 512640

INSTALLATION/LEVELLING

The 6-4 Series is designed to stand on a flat and level surface, however, any unevenness may

be overcome by adjusting the four levelling feet, one at each corner of the base plate. The

adjusting screws are accessed by removing left and right hand hotplate castings (See section

‘To Remove Hotplate Castings - Servicing Section Page 48). To raise the cooker turn screw

clockwise, to lower turn screw counter-clockwise.

There are rollers on the base of the cooker to allow for positioning.

When the cooker is in the correct position the four levelling feet can be adjusted to level the

cooker. The feet must be lowered enough to prevent the cooker rolling out of position. (See Fig.

5)

13

DESN 512391 BFig. 5

LEVELLING AND MOBILITY WHEELS

HOTPLATE CASTINGS

1. Attach earth cable from centre casting to cooker chassis and locate over burner bodies.

Repeat for LH and RH castings and that the gaskets are fitted where the outer castings

overlap centre castings. Ensure that earth cables are attached. (See Fig. 6A)

2. Secure castings using 8 profiled fixing nuts. DO NOT OVERTIGHTEN. (See Fig. 6B).

FITTING OF HOTPLATE CASTING AND PAN SUPPORTS

14

Fig. 6B

Fig. 6A

DESN 512393 C

DESN 512400 A

4. Position burner caps onto burner bodies. (See Figs. 7A, 7B & 7C)

15

Fig. 6C DESN 512419 A

3. Fit and secure six burner rings using M4 screws on rear left hand, front centre, front right

hand and rear right hand burners. Use No.6 3/8 screw on front left hand and centre rear

burners. (See Fig. 6C).

NOTE: The fitting of LH and centre burners are the same as shown in Fig. 6B.

Fig. 7A DESN 513714

ULTRA RAPID BURNER

DESN 513512

WOK BURNER

Fig. 7C DESN 511617

FITTING BURNER CAP - RAPID AND SEMI-RAPID BURNERS

BURNER CAP

RETAINING LUGS

16

Fig. 7B DESN 511618

BURNER CAP

ASSEMBLY OF RAPID AND SEMI-RAPID BURNERS

BURNER HEAD

ELECTRODE

5. Fit the pan supports in the following order The pan supports are marked on the underside to

correspond to the markings below. The pan supports must locate in the recesses in the

hotplate casting. (See Fig. 8A & 8B)

17

Important

It is very important for the performance and reliability of the hob that the pan supports are fitted

in accordance with the AGA SIX-FOUR SERIES - DC6 OWNERS MANUAL.

To help identify the correct location of the pan supports, the centre rear pan support has been

uniquely designed with a tag, as shown. This pan support must be fitted in the rear centre

position with the tag pointing towards the back of the appliance.

Fig. 8B DESN 512995 A

Fig. 8A DESN 513712 A

1. Locate tabs on rear of splashback assembly, into the brackets on the upper rear of the

cooker. (See Fig. 9).

Push fully into place.

Fig. 9

DESN 512394

18

SPLASHBACK

Fig. 8C DESN 513716

TO ADJUST PAN SUPPORT LEVEL

1. Loosen retaining nut using 8mm socket (See Fig. 8C).

2. To prevent rocking adjust the pan support foot using 2.5mm allen key.

3. Check pan support is level with opposing pan supports.

4. Retighten retaining nut.

HANDRAIL FITTING

1. Position handrail assembly onto locating studs at each end of facia. Ensure the grub screw

at each end of the hand rail is facing downwards.

2. Push handrail assembly fully against facia and lock in place by tightening 2 grub screws

(2

1

/

2 mm). (See Fig. 6A).

Users

Guide

19

20

GENERAL INFORMATION

As responsible manufacturers we take care to make sure that our products are designed and

constructed to meet the required safety standards when properly installed and used.

IMPORTANT NOTICE: PLEASE READ THE ACCOMPANYING WARRANTY.

Any alteration that is not approved by Aga could invalidate the approval of the appliance,

operation of the warranty and could affect your statutory rights.

In the interests of safety and effective use, please read the following before using your new Aga

appliance.

The use of gas on a cooking appliance results in the production of heat and moisture in the room

in which it is installed. Ensure that the kitchen is well ventilated, keep the natural ventilation holes

open or install a mechanical ventilation device (mechanical extractor hood).

Prolonged intensive use of the appliance may call for additional and/or more effective ventilation,

for example, opening of a window, or, increasing the level of mechanical ventilation where

present.

Installation must be to local and national wiring regulations and carried out by a qualified

engineer, from an authorized distributor.

A little smoke and some odour may be emitted when first switched on. This is normal and

harmless (from oven lagging and starch binder on the element insulation) and will cease after a

short period of use.

Your appliance has a gas hotplate, three electric ovens; the lower right hand oven is a slow

cooking (simmering) oven, the upper right hand (roasting) oven is a conventional oven.

The lower left hand (baking) oven is an electric fan oven. The fan behind the rear panel ensures

an even distribution of heat within the oven during cooking, ie. the temperature at the lowest shelf

position is the same as the temperature at the highest shelf position.

The electric broiler is situated in the roof of the top left hand compartment.

Refer to the diagram (See Fig. 10) to familiarize yourself with the cooker and refer to the relevant

section for the simmering oven, fan oven, conventional oven, broiler and gas hotplate etc.

Your cooker is supplied with the following accessories:

5 oven shelves

1 large roasting tin

1 broiler shelf

1 broiler pan

1 broiler grid

1 baking tray

The following loose parts are also packed with:

6 pan supports (cast)

3 spillage wells (cast)

6 burner caps

6 burner heads

6 burner skirts

1 burner ring

1 outer ring

1 handrail assembly

1 splashback assembly

1 fitting kit

6 gaskets

Page is loading ...

Aga Ranges SIX-FOUR SERIES - DC6 User manual

This manual is also suitable for

Aga Ranges SIX-FOUR SERIES - DC6 User manual

Related papers

Other documents