Miller AUTO DARKENING LENS, FIXED SHADE NO. 8, 9, 10, &11 Owner's manual

Miller
Brand
Miller
Model
AUTO DARKENING LENS, FIXED SHADE NO. 8, 9, 10, &11
Category
Bicycle accessories
Type
Owner's manual

This manual is also suitable for

OWNER’S MANUAL
ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2020 Miller Electric Mfg. Co.
FORM: OM-273493C 2020-02
Owner’s Manual For Auto Darkening Lens, Fixed Shade No. 8, 9, 10, And 11
1. Welding Helmet Safety Precautions − Read Before Using
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible haz-
ards are shown in the adjoining symbols or explained in the text.
Fsafe1 2013-10
Have only trained and qualified persons install, operate, or ser-
vice this unit. Read the safety information at the beginning of
these instructions and in each section. Call your distributor if you
do not understand the directions.
Fsafe15 2013-10
Indicates a hazardous situation which, if not avoided, could result
in death or serious injury. The possible hazards are shown in the
adjoining symbols or explained in the text.
Fsafe2 2013-10
Prolonged noise from some processes can damage hearing.
Wear approved ear protection if noise level is high.
Helsafe3 2013-10
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Fsafe3 2013-10
Welding helmets do not provide unlimited eye, ear and face protection. Use impact resistant safety spectacles or goggles and ear
protection at all times when using this welding helmet. Do not use this helmet while working with or around explosives or corrosive
liquids. This helmet is not rated for overhead welding. Do not weld in the direct overhead position while using this helmet unless addi-
tional precautions are taken to protect yourself from arc rays, spatter, and other hazards. Inspect the auto-lens frequently. Immediately
replace any scratched, cracked, or pitted cover lenses or auto-lenses. Use helmet for welding/cutting applications only.
Helsafe2 2018-08
Arc rays can burn eyes and skin. Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the weld. Wear a welding helmet fitted with a proper shade of filter to protect your face
and eyes from arc rays and sparks when welding or watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards). Refer to Shade
and Sensitivity charts. Wear approved safety glasses with side shields under your helmet. Use protective screens or barriers to protect
others from flash, glare, and sparks; warn others not to watch the arc. Wear body protection made from durable, flame-resistant material
(leather, heavy cotton, wool). Body protection includes oil-free clothing such as leather gloves, heavy shirt, cuffless trousers, high shoes,
and a cap.
Helsafe1 2018-01
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov
2. Specifications
Standard Lens 770660 770659 770226 770961
Clear LighttLens
287825 287828 287830 287833
Viewing Field 94 x 33 mm (3.7 x 1.37 in.)
Reaction Time 0.000277 seconds (1/3,600)
Available Shades Darkened State: No. 8
Light State: No. 3
Provides Continuous UV And
IR Protection
Darkened State: No. 9
Light State: No. 3
Provides Continuous UV And
IR Protection
Darkened State: No. 10
Light State: No. 3
Provides Continuous UV And
IR Protection
Darkened State: No. 11
Light State: No. 3
Provides Continuous UV And
IR Protection
Operating Temperature 14° to 131°F (−10° to 55°C)
Storage Temperature −4° to 158°F (−20° to 70°C)
Standards Meets ANSI Z87.1 And CSA Z94.3 Standards
Dimensions 108 x 51 x 5 mm (4.25 x 2.00 x 0.019 in.)
Auto-On And Auto-Off Circuitry. Solar-Powered, No Batteries Required.
3. Operating Instructions And Troubleshooting
The fixed shade models have no buttons or controls. The lens
turns on (darkens) automatically when welding begins and turns
off when welding stops. To ensure proper function, charge lens
internal battery prior to first use or after extended storage (about
30 days). Charge battery by either of these methods:
S Expose lens to direct sunlight for 10 seconds.
S Expose lens to artificial light (light bulb) for 20 seconds.
After initial charging, the welding arc will maintain the charge in
the battery.
Trouble Remedy
Auto lens not switching; lens stays light and
does not darken when welding.
Stop welding immediately. Press the Reset button on variable shade helmets. On fixed-shade helmets, make
sure the lens solar cell is properly charged by placing the helmet in direct sunlight for 20 minutes. If power is on,
review the sensitivity recommendations and adjust sensitivity. Clean lens cover and sensors of any obstructions.
Make sure the sensors are facing the arc; angles of 45_ or more may not allow the arc light to reach the sensors.
OM−273493 Page 2
4. Limited Warranty
LIMITED WARRANTY – Subject to the terms and conditions below, Miller Electric Mfg. LLC, Appleton, Wisconsin, warrants to its original
retail purchaser that the new Miller equipment sold after the effective date of this limited warranty is free of defects in material and work-
manship at the time it is shipped by Miller. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
Miller auto-darkening lens helmets are warranted for 2 years from the date of purchase. Proof of purchase is required for warranty trans-
actions so it is imperative that a copy of the original invoice or sales receipt be retained.
This warranty provides specific legal rights, and other rights may be available depending on your state or province.
For warranty transactions, contact your Miller Distributor.
Effective January 1, 2020
Miller Helmet Warr 2020-02
  • Page 1 1
  • Page 2 2

Miller AUTO DARKENING LENS, FIXED SHADE NO. 8, 9, 10, &11 Owner's manual

Miller
Brand
Miller
Model
AUTO DARKENING LENS, FIXED SHADE NO. 8, 9, 10, &11
Category
Bicycle accessories
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents