Minka Group 3011-613 User manual

Minka Group
Brand
Minka Group
Model
3011-613
Type
User manual

Minka Group 3011-613 is a single-light wall fixture designed for indoor use. It features a metal construction with a glass shade and a Xenon bulb (included). The fixture can be mounted on a wall or ceiling and is compatible with standard 120-volt electrical systems. It is easy to install and comes with all the necessary mounting hardware. The fixture is rated for a maximum of 75 watts and provides ample lighting for a variety of applications, including hallways, bedrooms, and living rooms.

Minka Group 3011-613 is a single-light wall fixture designed for indoor use. It features a metal construction with a glass shade and a Xenon bulb (included). The fixture can be mounted on a wall or ceiling and is compatible with standard 120-volt electrical systems. It is easy to install and comes with all the necessary mounting hardware. The fixture is rated for a maximum of 75 watts and provides ample lighting for a variety of applications, including hallways, bedrooms, and living rooms.

INSTALLATION INSTRUCTIONS
Item#3011-613 (New. 03/23/2017)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker.
If necessary, remove the old fixture, including the
mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Attach mounting plate (A) to the junction box by
using the mounting screws (B) (Size: #8-32N*L0.5”).
The side of the mounting plate marked “GND” must
face out.
CONNECTING THE WIRES (Fig. 2)
4. At this point, connect the electrical wires as shown
in Fig. 2, making sure that all wire connectors are
secured. If your outlet box has a ground wire (green
or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire
directly to the mounting plate using the green screw
provided. After the wires are connected, tuck them
carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig.1)
5. Place fixture body (C) over the mounting plate (A)
and secure it with screws (D).
6. Install the 1*75W Xenon bulb (I) (included) in
accordance with the fixture’s specifications.
(DO NOT
EXCEED THE MAXIMUM WATTAGE RATING!). (NE
PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!).
7. Place the glass shade (F) followed by metal ring (G)
over the socket
(E), fasten with screw shell (H) by
using the tool (K).
Your installation is now complete. Return power and
test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2697E
FIXTURE
WIRES
Black or
Smooth
H
O
U
S
E
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
U
S
E
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
H
O
U
S
E
WIRES
Green
(Ground)
Set#A-021-134117
-Mounting Plate
-Ground Screw
-Mounting Screw*2
K
B
A
D
C
G
H
I
F
E
  • Page 1 1

Minka Group 3011-613 User manual

Minka Group
Brand
Minka Group
Model
3011-613
Type
User manual

Minka Group 3011-613 is a single-light wall fixture designed for indoor use. It features a metal construction with a glass shade and a Xenon bulb (included). The fixture can be mounted on a wall or ceiling and is compatible with standard 120-volt electrical systems. It is easy to install and comes with all the necessary mounting hardware. The fixture is rated for a maximum of 75 watts and provides ample lighting for a variety of applications, including hallways, bedrooms, and living rooms.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI