Maytag Epic Z Owner's manual

Type
Owner's manual
®
EPIC
GAS DRYER
USE & CARE GUIDE
SECADORA A GAS
MANUAL DE USO Y CUIDADO
SECHEUSE A GAZ
GUIDE D'UTILISATION ET D'ENTRETIEN
FOR QUESTIONS ABOUT FEAIIJRES, OPERATION/PERFORMANCE,
PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900
IN CANADA, CALl: 1.800.807.6777
VISIT OUR WEBSII E AI WWW.MAYTAG.COM
IN CANADA, WWW.MAY EAG.CA
W10112943A
SI IIENE PREGUN[AS RESPECTO A [AS CARACTER[STICAS,
FUNCIONAMIENTO, RENDIMIENTO, PARIES, ACCESORIOS O
SERVIC[O TECNICO, LI AME AL: 1.800.688.9900
EN CANAD,g,, El AME AL: 1.800.807.6777
VISITE NUESTRO SITIO WEB EN
_/_/_A/.MAYTAG .COM
EN CANAD,g,, WWW.MAYEAG.CA
AU CANADA, POUR ASSISIANCE, INSTALLA|ION OU SERVICE,
COMPOSEZ I E : 1.800.807.6777
OU VISITER NOTRE SITEINTERNET ,_
WWW.MAYTAG.CA
_£:iiiiiiiiiiiiii@£!!@i!!!iiiiiii_ii_!!iiii!£_i_£_i__i:i!:_:_i!!iii!!i_ii_i!!_{_!i(!!_!_!_!_!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_¸¸
TABLE OF CONTENTS
DRYER SAFETY ...................................................................... 3
INSTALLATION INSTRUCTIONS ......................................... 5
Tools and Parts ................................................................... .-_
Optional Pedestal ............................................................... 5
Location Requirements ....................................................... 6
Electrical Requirements ...................................................... 8
Gas Supply Requirements .................................................. 9
Venting Requirements ...................................................... 10
Plan Vent System .............................................................. 12
Install Vent System ........................................................... 1
Install Leveling Eegs ......................................................... 1_
Make Cas Connection ...................................................... 14
Connect Vent ................................................................... 15
Level Dryer ...................................................................... 15
Reverse Door Swing ......................................................... 15
Complete Installation ....................................................... 17
DRYER USE.......................................................................... 18
Starting Your Dryer ........................................................... 18
Stopping or Restarting Your Dryer .................................... 19
I.ock Controls ................................................................... 19
Drying and Cycle Tips ...................................................... 19
Status I.ights ...................................................................... 20
Cycles .............................................................................. 20
Additional Features .......................................................... 21
Changing Cycles, Options and Modifiers ......................... 22
Drying Rack Option ......................................................... 22
DRYER CARE ...................................................................... 23
Cleaning the Dryer I.ocation ............................................ 2_
Cleaning the Lint Screen .................................................. 23
Cleaning the Dryer Interior ............................................... 24
Removing Accumulated Lint ............................................ 24
Vacation and Moving Care .............................................. 24
TROUBLESHOOTING ......................................................... 25
ASSISTANCE OR SERVICE ................................................... 27
WARRANTY ........................................................................ 28
_!_!_ii_!iii!_iii!!!iiii!!_iiii!i_!i:_i_iiiiii!i!ii!!_!!_jiii_¸ _i!iii!i£@:!i!ii@iiiiiiiiX{!!!!!!!!!!!!!!!!!!!!!!!!!!!@¢
P
INDICE
SEGURIDAD DE LA SECADORA ........................................ 29
INSTRUCCIONES DE INSTALACION ................................ 31
Herrarnientas y piezas ..................................................... 31
Pedestal optional ............................................................ 31
Requisitos de ubicaciGn ................................................... 32
Requisitos elGctricos ........................................................ 35
Requisitos del suministro de gas ...................................... 36
Requisitos de ventilaciGn ................................................. 37
PlanificaciGn del sistema de ventilaciGn .......................... 39
InstalaciGn del sistema de ventilaciGn ............................. 40
InstalaciGn de las patas niveladoras ................................. 40
ConexiGn del suministro de gas ....................................... 41
ConexiGn del ducto de escape ........................................ 42
NivelaciGn de la secadora ............................................... 42
CGmo invertir el cierre de la puerta ................................. 42
Complete la instalaciGn ................................................... 44
USO DE LA SECADORA ..................................................... 45
Puesta en marcha de la secadora ..................................... 45
Detenci6n o reanudaci6n de la marcha de la secadora... 46
Bloquear los controles ..................................................... 46
Sugerencias de ciclos y secado ........................................ 47
I.uces de estado ............................................................... 47
Ciclos .............................................................................. 48
Caracter[sticas adicionales ............................................... 49
Cambio de ciclos, opciones y modificadores .................. 49
OpciGn de estante de secado .......................................... 50
CUIDADO DE LA SECADORA .......................................... 51
Limpieza del lugar donde est.1 la secadora ...................... 51
I impieza del filtro de pelusa ............................................ 51
I]mpieza del interior de la secadora ................................ 5I
EliminaciGn de pelusa acumulada ................................... 52
Cuidado para las vacaciones y la mudanza ..................... 52
SOLUCION DE PROBLEMAS ............................................. 52
AYUDA O SERVICIO Tf_CNICO ......................................... 54
GARANTJA ......................................................................... 55
__!_i!!iiiiiiiiiiiiiiiiiiiiiiiiii!i!!@ii!!!!!!!!!!!!!!!!!ili!i!i!!ii!i!!:_jiib 5ii!i£@iiii_ii!iiii!_£!il]iiiiiiiiiiiiiiii_i_!ii!{iiiiiiill¸i_
TABLE DES MATIERES
Sf_CURITI_ DE LA Sf_CHEUSE ............................................... 56
INSTRUCTIONS D'INSTALLATION ................................... 58
Outillage et pi_ces ........................................................... 58
PiGdestal facultatif ............................................................ 58
Exigences d'emplacement ................................................ ,g9
SpGcifications 61ectriques ................................................. 61
Alimentation en gaz ......................................................... 62
Exigences concernant 1'Gvacuation .................................. 64
Planification du systGme d'Gvacuation ............................. 65
Installation du systGme d'Gvacuation ................................ 67
Installation des pieds de nivellement ............................... 67
Raccordement au gaz ...................................................... 68
Raccordement du conduit d'Gvacuation .......................... 68
Mise _ niveau de la sGcheuse ........................................... 69
Inversion du sens d'ouverture de la porte ........................ 69
Achever I'installation ....................................................... 71
UTILISATION DE LA Sf_CHEUSE ........................................ 72
Mise en marche de la s6cheuse ....................................... 72
Arr@ ou remise en marche de la s6cheuse ....................... 7_¢
Verrouillage des commandes ........................................... 73
Conseils pour le s6chage et les programmes .................... 74
T6moins lumineux ........................................................... 74
Programmes ..................................................................... 75
Caract6ristiques suppl6mentaires ..................................... 76
Changement des programmes, options et
modificateurs ................................................................... 77
Option de grille de s6chage ............................................. 77
ENTRETIEN DE LA SI_CHEUSE ........................................... 78
Nettoyage de I'emplacement de la sGcheuse ................... 78
Nettoyage du filtre _ charpie ............................................ 78
Nettoyage de I'intGrieur de la sGcheuse ............................ 79
Retrait de la charpie accumulGe ....................................... 79
PrGcautions _ prendre pour les vacances et avant un
dGmGnagement ................................................................ 79
DI_PANNAGE ...................................................................... 80
ASSISTANCE OU SERVICE .................................................. 82
GARANTIE .......................................................................... 83
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
I WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death,
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
[] Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
[] Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed
to the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
[] See installation instructions for grounding requirements.
SAVE THESE iNSTRUCTiONS
In the State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.
iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
4
:ili;iiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiiiiiiiIi!iiiiIi!iiiiIi!iiiiIi!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiii_iii!i:iii!_!_!_!_!_i!!ii!_i!_!_!_!_!_i!i_ii!_i!ii!!_!_!_!_!!!g!!>:i_!;i_!!!ii:;>_!_i_!;i_!_i!!!!!!!!!_i_!ii!!!_i!!_!iiiii!_!:!_!!il!!!!!!!ii!_iiiiiii_i¸ !!_!_!_!_!_!_i!i_ii!_i!_ii!!_!_!_!_!_i!i_ii1!_!_!_!_!!_!Ii_i!ii_i_!!!iii!i:iii!!_i!!ii_iiii!!_!_i!i_ii!_i_!ii!ii!!_!_!!i!!:!ii_iiii_iXi_i_i_i!i!iiiii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i!!!iiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i_¸i¸
INSTALLATION INSTRUCTIONS
Gather fine required tools and parts before starting installation. Read and follow the
instructions provided with any tools listed here.
8" or 10" pipe wrench
8" or 10" adjustable wrench (for gas
connections)
Flat-blade screwdriver
Adjustable wrench that opens to 1"
(2.54 cm) or hex-head socket wrench
(for adjusting dryer feet)
V2' nut driver or socket wrench
(recommended)
level
Vent clamps
Knife
Pipe-joint compound resistant to [.P gas
Caulking gun and compound (for
installing new exhaust vent)
Pliers
Tape measure
Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of
different heights separately for this dryer. You may select a 10" (25.4 cm) pedestal or a
15.5' (5¢9.4 cm) pedestal with a storage drawer. [he pedestal will add to the total height of the
dryer for a total height of approximately 46" (11 6.8 cm) or 51.5' (1 _¢0.8cm), respectively.
For a garage installation, you will need to place the 10" (25.4 cm) pedestal at least
9' (22.9 cm) above the floor. You will need to place the 15.5' (5¢9.4 cm) pedestal at least
3' (7.6 cm) above the floor.
Parts supplied
Remove parts package from dryer drum. Check that all parts were included.
4 [ewfling legs
NOTE: Do not use leveling legs if installing the dryer on a pedestal.
Parts needed
Check local codes and with gas supplier. Check existing gas supply, electrical supply and
venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing parts.
For close-clearance installations between 28.65" (72.77 cm) and 34.15" (86.74 cm), see
"Plan Vent System" section for venting requirements.
(86.74 cm)
Mobile home installations require special parts (listed following) that may be ordered by
calling the dealer from whom you purchased your dryer. For further information, please refer
to the "Assistance or Service" section.
Mobile Home Installation Kit. Ask for Part Number 346764.
Optional pedestal ( t5.5" 139.4 cm] model shown)
The pedestals are available in several colors.
lb order, call the dealer from whom you purchased your dryer or refer to the "Assistance or
Service" section.
Pedestal Height Color Part Number
10" (25.4 cm) White MHP1000SQO
10" (25.4 cm) Black MHP1000SB0
15.5" (39.4 cm) White MHP1500SQ0
15.5" (39.4 cm) Black MHP1500SB0
15.5" (39.4 cm) Pacific Blue MHP1500SK0
Stack Kit
Are you planning to stack your washer and dryer? 1o do so, you will need to purchase a Stack
Kit. lo order, call the dealer from whom you purchased your dryer or refer to the "Assistance
or Service" section. Ask for Part Number 8212640.
Metal exhaust system hardware.
I( (.= Iio
Dryer Dimensions
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
(91.4 cm)
50"
128.27 cm)
You will need
A location that allows for proper exhaust installation. A gas dryer must be exhausted to
the outdoors. See "Venting Requirements."
A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See
"Electrical Requirements."
A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight
of a companion appliance should also be considered.
A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (if slope is greater
than 1" [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not
tumble properly and automatic sensor cycles may not operate correctly if dryer is not
level.
For a garage installation, you will need to place the dryer at least 18" (46 cm) above the
floon If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.
Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer
might not shut off at the end of an automatic cycle. Drying times can be extended.
The dryer must not be installed or stored in an area where it will be exposed to water and/or
weather.
Check code requirements. Some codes limit, or do not permit, installation of the dryer in
garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.
Installation clearances
The location must be large enough to allow the dryer door to open fully.
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the
exhaust vent with elbow. See "Venting Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested
for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be
considered for the following reasons:
Additional spacing should be considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and bottom
of the door are required. [ ouvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
Custom undercounter installation - Dryer only
.... 2"*
"'1o 'c
1"* _ "_-_27"_ "_-- 1"*
2.5 crn 68.6 cm 2.5 cm
*Required spacing
6
Closet installation - Dryer only
II "1:11_1tll I I 24in.2 _
L_I(155o=2,
h"*_ 20.05"_1_"**1
(2.5 cm) (72.77 cm) (12.7 cm)
A B
A. _id_' vi_'w - closet or confined area
B.Closet door with vents
*Required spacing
**For side or bottom venting, O" (0 cm) spacing is allowed.
Recessed or closet installation - Dryer on pedestal
I O0
23.*
(7.6 crn)
f
1"--_ I_ 27"_'t "_--1" 11"*1"_26.65"_'-Is"**l
(2.5 cm) ' (68.6 cm) ' (2.5 cm) (2.5 crn) (72.77 crn) (12.7 cm)
A B
A. R_'c_'ss_'ctar_'a
B. Side"vie'w - closet or confined are'a
*Required spacing
**For side or bottom venting, O" (0 cm) spacing is allowed.
7"*(17.8cm)
* Required spacing
7"*(17.8crn)
[9"*
r (22.9 crn)
,, ,, ..........................
(12.7 cm)(72.77crn) (2.5cm) (2.5crn)(58.5cm)(2.5 cm)
** For side or bottom venting, 0" (0 cm) spacing is allowed.
Recommended installation spacing for recessed or closet installation, with
stacked washer and dryer
The dimensions shown are for the recommended spacing.
48 iil. 2 *
(310 crn2)
T
o
24 ill 2 *
(155cm2)
V
3"* (7.6 cm)
3"*(7.6crn)
1"*(2.5cm)
*Required spacing
Recommended installation spacing for cabinet installation
For cabinet installation, with a door, minimum ventilation openings in the top of the
cabinet are required.
!_i¸I¸I¸I¸I¸I¸I¸I¸I¸i¸II!I¸iii_:!_ii!iii!iii!iiiiiiiiiiiiiiiiiiii¸i¸i¸iiii!!:_iii_!i!_!i!i;iiiiiiiiiiiiiiiii ....iiii_,_,_,_,_,_,_,_,_,_7
t
72"
(162.9 crn)
J
(2.5crn)
5Y2"**--_- ,_- 1"
(14crn) (2.5crn)
_- .Jj
(66.6 cm)
*Required spacing
**For venting out the side, 1"/2.5 cm) spacing is allowed.
Mobile home - additional installation requirements
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280) or to the Canadian Manufactured Home Standard,
CAN/CSA-Z240 MH.
Mobile home installations require:
[] Metal exhaust system hardware, which is aw3ilable for purchase from your dealer.
[] Mobile Home Installation Kit Part Number 346764. See '"]bols and Parts" section for
information on ordering.
[] Special provisions must be made in mobile homes to introduce outside air into the dryer.
[he opening (such as a nearby window) should be at least twice as large as the dryer
exhaust opening.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay
fuse or circuit breaker is recommended. [t is also recommended that a separate circuit
serving only this dryer be provided.
GROUNDING INSTRUCTIONS
[] For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
SAVE THESE INSTRUCTIONS
8 ...........
Explosion Hazard
Use a new CSA international approved gas supply line.
Install a shut=off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel,
Failure to do so can result in death, explosion, or fire.
Gas Type
Natural gas:
This dryer is equipped for use with Natural gas. It is design-certified by CSA International for
[P/propane or butane) gases with appropriate conversion.
Your dryer must have the correct burner for the type of gas in your home. Burner
information is located on the rating plate in the door well of your dryer. If this information
does not agree with the type of gas available, contact your dealer or call the phone
numbers referenced in the "Assistance or Service" section.
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from tile gas specified on the r'nodel/serial
rating plate for use with a different gas without consulting your gas company.
Gas Supply Line:
Must include 1/8"NPT minimum plugged tapping accessible for test gauge connection,
immediately upstream of the gas connection to the dryer (see illustration).
Y2" IPS pipe is recommended.
%" approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if
local codes and gas supplier permit.
If you are using Natural gas, do not use copper tubing.
lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.
If your dryer has been converted to use [P gas, %" I.P compatible copper tubing can be
used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.
NOTE: Pipe-joint compounds that resist the action of I.P gas must be used. Do not use
TEFI.ON _'_tape.
Must include a shutoff valve:
In the U.S.A.:
An individual manual shutoff w_lve must be installed within six (6) feet (1.8 m) of the dryer
in accordance with the National Fuel Gas Code, ANSI Z223.1. ]he location should be
easy to reach for opening and closing.
In Canada:
An individual manual shutoff valve must be installed in accordance with tile Bq49.1,
Natural (];as and Propane Installation Code. [t is recommended that an individual manual
shutoff valve be installed within six (6) feet (1.8 m) of the dryer. The location should be
easy to reach for opening and closing.
A C E
B D
A. ?g" flexible gas connector
B. _" pipe to flare adapter fitting
C. _" NPT minimum plugged tapping
D. _//' NPT gas supply line
E. Gas shutoff valve
t®TEFLON is a legistered trademark of E.I. DLI Pont De Nemouls and Company.
9
Gas supply connection requirements
Use an elbow and a %" flare x %" NPT adapter fitting between file flexible gas connector
and the dryer gas pipe, as needed to avoid kinking.
Use only pipe-joint compound. Do not use TEFI.ON _'*tape.
[his dryer must be connected to the gas supply line with a listed flexible gas connector
that complies with the standard for connectors for gas appliances, ANSI Z21.24 or
CSA 6.10.
Burner input requirements
Elevations up to 10,000 ft (3,048 m):
The design of this dryer is certified by CSA International for use at altitudes up to 10,000 ft
(3,048 m) above sea level at the Btu rating indicated on the model/serial number plate.
Burner input adjustments are not required when the dryer is operated up to this elevation.
Elevations above 10,000 ft (3,048 m):
When installed above 10,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown
on the model/serial number plate is required for each ,000 ft (305 m) increase in
elevation.
Gas supply pressure testing
The dryer must be disconnected from the gas supply piping system during pressure testing
at pressures greater than _/2psi.
Dryer gas pipe
The gas pipe that comes out through the rear of your dryer has a %" male pipe thread.
A. 1/_,, NPT gas supply line
B. _" NPT dryer pipe
*NOTE: If the dryer is mounted on a pedestal, the gas pipe height must be an additional
10. (25.4 cm) or1 _._.._r_,,/39.4 cm) from the floor, del)ending on the pedestal modeh For a
garage installation, the gas pipe height must be an additional 18" (46 cm) from the floor.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
WARNING: lb reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a
concealed space of a building.
If using an existing vent system
C'lean lint from the entire length of the system and make sure exhaust hood is not plugged
with lint.
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.
Review Vent system chart. Modify existing vent system if necessary to achieve the best
drying performance.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent.
4" (10.2 cm) heavy metal exhaust vent and clamps must be used.
4" (10.2 cm) heavy metal _'xhaust v_'nt
Vent products can be purchased from your dealer or by calling Maytag Services. For more
information, see the "Assistance or Service" section.
10 ...........
Rigid metal vent
For best drying performance, rigid metal vents are recommended.
Rigid metal vent is recommended to avoid crushing and kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for cleaning.
Flexible metal vent must lye fully extended and supported when the dryer is in its final
location.
Remove excess flexible metal vent to avoid sagging and kinking that may result in
reduced airflow and poor performance.
Do not install flexible metal vent in enclosed walls, ceilings or floors.
Elbows
45 ° elbows provide better airflow than 90 ° elbows.
Clamps
Good Better
Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws or other fastening devices
that extend into the interior of the duct. Do not use duct tape.
Clamp
Exhaust
Recommended hood styles are shown here.
B
(10.2 cm)
A. Louv_'md hood style
B.Box hood style
The angled hood style (shown here) is acceptable.
4"
(10.2 cm)_
v_ 21/2"
(6.4 cm)
An exhaust hood should cap the vent to keep rodents and insects from entering the home.
Exhaust hood must lye at least 12" (30.5 cm) from the ground or any object that may be in
the path of the exhaust (such as flowers, rocks or bushes, snow line, etc./.
Do not use an exhaust hood with a magnetic latch.
improper venting can cause moisture and lint to collect
indoors, which may result in:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the dryer. Other installations are possible.
B
......................................C
F
.....................................G
A. Dryer
B. Elbow
C. Wall
D. Fxhaust hood
E. Cla raps
£ Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows
H. fxhaust outlet
Optional exhaust installations
Fire Hazard
Cover unused exhaust holes with one of the
following kits:
279818 (white)
279820 (black)
280102 (pacific blue)
Contact your local dealer.
Failure to follow these instructions can result in death,
fire, electrical shock, or serious injury.
This dryer can be converted to exhaust out the right side, left side, or through the bottom.
Contact your local dealer to have the dryer converted.
B
A. Standard rear offset exhaust installation
B. Left or right side exhaust installation
C. Bottom exhaust installation (not an option with
pedestal installations)
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for your installation. Two close-
clearance installations are shown. Refer to the manufacturer's instructions.
!z__,'>... ...........
<
i i
, ._===-f/"
i i /z
i t/
i u
x\ ii
,.__ _ X.L __
A B
A. Over-the-top installation taho available with one
offset elbow)
B.P_'riscope installation
NOTE: The following kits for close clearance alternate installations are available for purchase.
Please see the "Assistance or Service" section to order.
Over-the-]op installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent mismatch/:
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch
Part Number 4396014- 29" (73.66 cm) to 50" (127 cm) mismatch
12
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home
structure and must not terminate beneath the mobile home. [erminate the exhaust vent
outside.
Determine vent path
Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns.
When using elbows or making turns, allow as much room as possible.
Bend vent gradually to avoid kinking.
Use the fewest 90 ° turns possible.
Determine vent length and elbows needed for best drying performance
Use the following Vent system chart to determine type of vent material and hood
combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust
systems longer than those specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and increased energy usage.
]he Vent system chart provides venting requirements that will help to achieve the best drying
performance.
Vent system chart
NOTE: Side and bottom exhaust installations have a 90 ° turn inside the dryer. lb determine
maximum exhaust length, add one 90° turn to the chart.
Number of Type of Box or Angled
90 ° turns vent Iouvered hoods
or elbows hoods
0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)
Flexible metal 36 ft (11 m) 28 ft/8.5 m)
1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)
Flexible metal 31 ft (9.4 m) 23 ft (7 m)
2 Rigid metal 44 ff (13.4 m) 38 ft (11.6 m)
Flexible metal 27 ff (8.2 m) 19 ft (5.8 m)
3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)
Flexible metal 25 ff (7.6 m) 17 ft (5.2 m)
4 Rigid metal 27 ff (8.2 m) 21 ft (6.4 m)
Flexible metal 23 ff (7 m) 15 ft (4.6 m)
2.
3.
Install exhaust hood. Use caulking compound to seal exterior wall opening around
exhaust hood.
Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust
hood with 4" (10.2 cm) clamp.
Run vent to dryer location. Use the straightest path possible. See "]Z)etermine vent path" in
"Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior of the vent to secure vent.
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
lb protect the floor, use a large flat piece of cardboard from the dryer carton. Place
cardboard under the entire back edge of the dryer.
!_iiiilZii!iiii_:!!ii!iii!iii!iiiiiiiiiiiiiiiiiiiiiiiiii!!:_%iiiiiiii ....iiii_,_,_,_,_,_,_,_,_,_I:}
2. Firmly grasp the body of the dryer. Gently lay the dryer on the cardboard. See illustration.
3. Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the
diamond marking is no longer visible.
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.
Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.
Leave enough room to connect the exhaust vent or gas line.
For mobile home use
Gas dryers must be securely fastened to the floor at the time of installation.
Mobile home installations require a Mobile Home Installation Kit. For more information,
please reference the service numbers in the "Assistance or Service" section.
1,
2.
Remove the red cap from the gas pipe.
Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound
on the threads of all non-flared male fillings. If flexible metal tubing is used, lye sure there
are no kinks.
A ........
A. Hared male fitting
B. Non-flared male fitting
NOTE: For [.P gas connections, you must use pipe-joint compound resistant to the action
of [P gas. Do not use TEFLON _°*tape.
A combination of pipe fittings must lye used to connect the dryer to the existing gas line.
Shown is a recommended connection. Your connection may lye different, according to the
supply line type, size and location.
!
A
A. _" flexible gas connector
B. ?_" dryer pipe
C. _" to _" pipe elbow
D. _" pipe-to-flare adapter fitting
C
t(=:TEFLON is a legistered trademark of E.I. Du Pont De Nemours and Company.
14 ...........
3. Opentheshutoffvalveinthesupplylille,lhevalveisopenwhenthehandleisparallelto
thegaspipe.
4.
A. Closed valve
B.Open valve
[_st all connections by brushing on an approved noncorrosive leak-detection solution.
Bubbles will show a leak. Correct any leak found.
£o nect %n
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to
existing vent, make sure the vent is clean. [-he dryer vent must fit over the dryer exhaust
outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a
4" (10.2 cm) clamp.
2. Move dryer into its final location. Do not crush or kink vent.
3. (On gas models) Check that there are no kinks in the flexible gas line.
4. Once the exhaust vent connection is made, remove the corner posts and cardboard.
Check the levelness of the dryer. Check levelness first side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs
up or down and check again for levelness.
You can change your door swing from a right-side opening to a left-side opening, if desired.
1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.
Remove the door assembly
1. Remove the 4 screws that hold the door hinge on the front panel of the dryer.
\
A. Dryer front panel
B. Door assembly
2. I.ay the door assembly on a flat, protected surface with the inside (inner door assembly/
facing up.
3. Remove the 6 Phillips head screws to release the outer door assembly from the inner door
assembly, as indicated below. See illustration. It is important that you remove only the
6 indicated screws.
4. I.ift the inner door assembly off the outer door assembly.
5. Rotateouterdoor180°.
180 °
Reverse hinge
1. Use a small flat-blade screwdriver to remove 2 plug strips from the inner door. Slide the
head of the screwdriver under the plugs, being certain not to scratch the inner door
surface, lift up.
2,
Remove the 4 screws that attach to the inner door hinge and move the hinge to the other
side. Reinstall the 4 screws.
°/
A. Door hinge
3. Reinstall plug strips on opposite side of the inner door.
4. Check for fingerprints on the glass. Clean glass if necessary.
5. Place the inner door assembly inside the outer door assembly. To fit correctly, the inner
door assembly edge fits completely inside the outer door assembly edge.
6. Reassemble the inner and outer door assemblies with the 6 screws.
16 ...........
Reverse the strike
1. Use a small flat-blade screwdriver to remove plug strip from the dryer door opening. Slide
the head of the screwdriver under the plugs, being certain not to scratch the dryer surface.
I.ifl up.
2. Remove the strike
3. Insert strike on the opposite side.
(
A
A. Plug strip (cannot be seen from thi_ angle)
B.Door strike
Reinstall the door
1. Reattach door to dryer front panel with the 4 screws.
1. Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
2. Check that you have all of your tools.
3. Check the dryer's final location. Be sure the vent is not crushed or kinked.
4. Check that the dryer is level. See "level Dryer."
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result indeath,
fire, or electrical shock.
®
\
\\\\\
5_
6.
7.
8.
9.
10.
A. Dryer front panel
B.Door assembly 11.
2. Check for fingerprints on the glass. Clean glass if necessary.
3. Close door and check that it latches securely.
Plug into a grounded 3 prong outlet. Turn on power.
Remove any protective film or tape remaining on the dryer.
Dispose of/recycle all packaging materials.
Read "Dryer Use."
Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.
Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only
[emperature setting.
If the dryer will not start, check the following:
Controls are set in a running or "On" position.
Start button has been pushed firmly.
Dryer is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
Household fuse is intact and tight, or circuit breaker has not tripped.
Dryer door is closed.
When the dryer has been running for 5 minutes, open the dryer door and feel for heat. [f
you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and
check that the gas supply line shutoff valve is open.
[f the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as
outlined above.
If the gas supply line shutoff valve is open, contact a qualified technician.
17
POWER DELICATE
WET 1 WRINKLE
DAMP 0 CONTROL
COOL DOWN NORMAl,,
DRY MOll
WRINKLE PREVENT _OtM_L
CONTROLS LOCKED ;_i 0 TOWEL£COTTON/_
CLEAN LINT SCREEN !!_!!
DRYNESS
LEVEL
START
PAUSEo
CANCEL
_Juft
HIGH
REGULAR
MEDIUM
LOW
EXTRA LOW
AIR FLUFF
©
O WRINKLE
PREVENT
-,_--,,,............. ,t,,_I( I.II" I.FI"_/I)I
/
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death
or fire.
Follow these basic steps to start your dryer. Please refer to specific sections of this manual for
more detailed information. This information covers several different models. Your dryer
may vary from the model shown and may not have all the cycles and features described.
1. Clean lint screen before each load. See "Cleaning the I.int Screen."
2. Place laundry in dryer and shut door.
3. Press POWER.
4_
Select a Sensor Dry or Timed Dry Cycle. The preset setti%s for Sensor Dry or Timed Dry
Cycles will illuminate. The estimated (Sensor Dry cycle) or actual (Timed Dry) cycle time
(in minutes) will show in the display.
NOTE: A default time is displayed when an automatic cycle is selected. Durin# the first
few minutes of the dryi% process, the cycle time may automatically vary from the default
time based on the size and fabric type of the load. toward the end of the dryin8 process,
the estimated time display will adjust asain, showin# the final dryi% time.
18
5.
6.
7.
To use a Sensor Dry Cycle
Select a Sensor [Dry Cycle. Sensor Dry Cycles are preset to Normal Cycle.
Select DRYNESS I.EVEI. to adjust how dry you want the load. As the cycle runs, the
control senses the dryness of the load and adjusts the time automatically for the
selected dryness level.
To make changes to the Dryness Level and/or Options during a Sensor Dry Cycle:
Press PAUSE/CANCEl once.
Adjust Dryness I.evel and/or Options.
NOTE: Dryness I.evel selections can be made only while using Sensor Dry Cycles.
Selecting More, Normal or I.ess automatically adjusts the sensed time needed.
M0 RE
I NORMAL
LESS
©
DRYNESS
LEVEL
SENSOR DRY ONLY
Sensor Dry cycles take the guesswork out of drying time and enhances fabric care.
The amount of time that is displayed is the estimated time remaining in the cycle.
To use a Timed Dry Cycle
Select a Nmed [Dry Cycle.
Press the Timed Dry Cycle Adjust Up or [Down arrow buttons until the desired drying
time is displayed, lap the limed L)ry Cycle Adjust Up or L)own arrow buttons and the
time will change by 1-minute intervals. Press and hold the Timed Dry Cycle Adjust
Up or [])own arrow buttons, and the time will change by S-minute intervals.
NOTE: The Timed Dry Cycle Adjust feature can be used only with Timed [Dry Cycles.
_ TIMED DRYCYCLE
ADJUST
Press TEMPERATURE until the desired temperature illuminates.
To make changes to Time and/or options during a Timed Dry Cycle:
Press PAUSE/CANCEl once.
Adjust the Time and/or Options.
iOPT[ONAL STEP) [f desired, select WRINKLE PREVENT. For more details, see "WR[NK[E
PREVENT" in the "Additional Features" section.
iOPT[ONAL STEP) The Cycle Signal is preset to on. [f desired, you may turn the Cycle
Signal off by pressing the Cycle Signal button.
Press and hold START for approximately 1 second until dryer starts. Be sure the door is
closed.
[f you do not press Start within 5 minutes of selecting a cycle, the dryer automatically
shuts off.
To pause/stop the dryer at any time
Open the door or press PAUSE/CANCEl once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
To end/cancel your dryer at any time
Press PAUSE/CANCEl. twice or open the door.
NOTE: Drying will continue from where the cycle was interrupted if you close the door and
press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will
shut off. Select new cycle settings before restarting the dryer.
/ < "' .........L,
This feature allows you to lock your settings to avoid unintended use of the dryer. You can also
use the control lock feature to avoid unintended cycle or option changes during dryer
operation. ......
To enable the control lock feature: (,i:
Press and hold CYCI.E SIGNAl. button for 3 seconds. The CONTROI.S lOCKED icon lights
up, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAl button for
3 seconds. The indicator light turns off.
Select the correct cycle and dryness level or temperature for your load. If a Sensor [Dry Cycle
is running, @e display shows @e esfim_ted cycle time, which is determined by your dryer
automatically sensing the dryness level of your load. If a Timed Dry Cycle is running, the
display shows the exact number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool
Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
Follow care label directions when they are available.
If desired, add a fabric softener sheet. Follow package instructions.
[b reduce wrinkling, remove the load from the dryer as soon as tumbling stops. ]his is
especially important for permanent press, knits, and synthetic fabrics.
Avoid drying heavy work clothes together with lighter fabrics. This could cause
overdrying of lighter fabrics and lead to increased shrinkage or wrinkling.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Sensor Dry Cycles or Timed Dry Cycles Preset Settings chart (in the "Cycles"
section) for a guide to drying various loads.
Drying temperature and Dryness Level are preset when you choose an Sensor [Dry
Cycle. You can select a different dryness level, depending on your load, by pressing
Dryness ].evel and choosing More or ].ess.
NOTE: You cannot use the Timed Dry Cycle Adjust Up or Down arrow buttons and
you cannot modify temperature with the Sensor Dry cycles.
[f you wish to adjust the cycle length of a Timed Dry Cycle, press the Timed Dry Cycle
Adjust up or down arrow buttons. Adjust the temperature of a Timed [Dry Cycle by
pressing TEMPERATURE until the desired temperature is selected.
NOTE: You cannot use the [Dryness level with Timed Dry Cycles.
Follow the progress of your dryer with the drying Status indicator lights.
WET
DAMP @
COOL DOWN
DRY
WRINKLE PREVENT
CONTROLS LOCKED
C LEAN LI NT SCREEN _:
Wet
The Wet light illuminates at the beginning of a Sensor Dry Cycle if a wet item is detected.
In a Sensor Dry Cycle, if a wet item is not detected after approximately 5 minutes, the
dryer goes directly into Cool Down and the Cool Down and WR[NK[E PREVENT
indicators illuminate, if selected.
In a Timed Dry Cycle, wet items are not detected. The dryer will continue to run for the
length of time selected, and the Wet light will illuminate. The damp light will not
illuminate.
WRINKLE PREVENT
The WRINKLE PREVENT light illuminates when this option is selected. This indicator stays on
with [Dry.
Clean Lint Screen
The Clean I.int Screen light is a reminder to check to see whether the lint screen needs to be
cleaned. The Clean [.int Screen light will come on when the machine is turned on. The light
will flash until the cycle is started or the door is opened, and then the light will turn off.
Indicator lights
Other indicator lights show Cycle, Options and Modifier settings selected.
Select the drying cycle that matches the type of load you are drying. See the Sensor Dry
Cycles Preset Settings chart or the Timed [Dry Cycles Preset Settings chart.
DELICATE
WRINKLE
CONTROL
NORMAL. TIMED
" DRY
JEANS - _RAPID
DRY
COTTON/ " FRESHEN
TOWELS UP
SENSOR DRY TIMED DRY
Sensor Dry Cycles
Sensor Dry Cycles allow you to match the cycle to the load you are drying. See the following
Sensor Dry Cycles Preset Settings chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and automatically adjusts the drying
time for optimal drying.
Cotton/Towels or Heavy Duty
Use this cycle to get high heat for heavy fabrics such as cotton towels or bedspreads.
Jeans
Use this cycle to get regular heat for drying denims.
Damp
The Damp light illuminates in a Sensor Dry Cycle when the laundry is approximately 80%
dry.
Cool Down
The Cool Down light illuminates during the cool down part of the cycle. [aundry cools for
ease in handling.
Dry
The Dry light illuminates when the drying cycle is finished. ]his indicator stays on during
WRINKI.E PREVENT.
Normal
Use this cycle to get rnedium heat for drying sturdy fabrics such as sturdy work clothes and
sheets.
Wrinkle Control
Use this cycle to get low heat for drying no-iron fabrics such as sport shirts, casual business
clothes and permanent press blends.
Delicate
Use this cycle to get extra-low heat for drying synthetic fabrics, washable knit fabrics and no-
iron finishes.
20 ...........
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Maytag Epic Z Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI