ZUUM Media LSPTZ-2MP-IP-2.7-11MM-IR30 Installation guide

Brand: ZUUM Media

Model: LSPTZ-2MP-IP-2.7-11MM-IR30

Type: Installation guide

IR Intelligent Speed Dome Installation Manual

Version 1.0.0

ZM111317

Table of Contents

INTELLIGENT SPEED DOME INSTALLATION PREPARATION

........................ 1

1.1

Basic Requirement

................................................................................................................................. 1

1.2

Check installation space and installation location intension

............................................................ 1

1.3

Please keep all package material well for future use

........................................................................ 1

SETUP BEFORE INSTALLATION

....................................................................... 2

2.1

Check Accessories

................................................................................................................................. 2

2.2

Open Device

............................................................................................................................................ 2

2.3

About Ceiling Installation Position Map

............................................................................................... 2

2.4

TF Card Slot and Reset Button

............................................................................................................ 3

CEILING INSTALLATION

.................................................................................... 4

3.1

Installation Components

........................................................................................................................ 4

3.2

Ceiling Installation Steps

....................................................................................................................... 4

3.2.1 Installation Requirements ................................................................................................................. 4

3.2.2 Installation Steps ................................................................................................................................ 4

WALL MOUNT BRACKET INSTALLATION

......................................................... 6

4.1

Component Installation

.......................................................................................................................... 6

4.2

Installation

................................................................................................................................................ 6

4.2.1 Installation Requirements ................................................................................................................. 6

4.2.2 Installation Steps ................................................................................................................................ 6

APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE PROTECTION

......... 13

APPENDIX Ⅱ 24V AC WIRE GAUGE AND TRANSMISSION DISTANCE

RELATIONSHIP SHEET

........................................................................................... 14

ZM111317

APPENDIX Ⅲ 12V DC WIRE GAUGE AND TRANSMISSION DISTANCE

RELATIONSHIP SHEET

........................................................................................... 15

APPENDIX Ⅳ WIRE GAUGE REFERENCE SHEET

........................................ 16

Welcome

Thank you for purchasing our Network speed dome camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual for future reference!

Important Safeguards and Warnings

．

Electrical safety

All installation and operation here should conform to your local electrical safety codes.

Please check if the power supply is correct before operating the device.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply

requirement is subject to the device label).

Please prevent the line cord from being damaged, especially the plug, power socket and the

junction from the device.

Note: Do not connect PoE and standard 12V power supply sources to the device at the

same time; it may result in device damage!

We assume no liability or responsibility for fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

．

Environment

Please do not aim the device at strong light (such as lightning, sunlight etc.) to focus; otherwise it

may cause overexposure (It is not the devices malfunction), which will affect the longevity of

CCD or CMOS.

Please transport, use and store the device within the range of allowed humidity and temperature.

Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold

and with strong electromagnetic radiation or unstable lighting.

Please do not allow water and other liquid to fall into the camera to prevent internal components

to be damaged.

Please keep the camera well ventilated to prevent heat accumulation.

Please pack the device with standard factory packaging or material with same quality when

transporting the device.

ZM111317

iii

Heavy stress, violent vibration or heavy water splash are not allowed during transportation,

storage and installation.

3. Operation and Daily Maintenance

Please do not touch the heat dissipation component of the device directly to avoid burn.

Please do not dismantle the device; there is no component which can be fixed by users

themselves in the camera. It may cause water leakage or bad image for the device due to

unprofessional dismantling.

It is recommended to use the device with surge proof device to improve surge resistance.

The grounding holes of the product are recommended to be grounded to further enhance the

reliability of the camera.

Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the

dust or dirt on the lens surface. Please use a dry cloth moistened by alcohol to wipe away the

dust gently if it is necessary to clean.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water

to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to

clean the device. Don’t use volatile solvent like alcohol, benzene, thinner etc. or strong detergent

with abrasiveness, otherwise it will damage the surface coating or reduce the working

performance of the device.

Dome cover is an optical device, please don’t touch or wipe cover surface directly during

installation and use, please refer to the following methods to deal with once dirt is found:

- Stained with dirt

Use oil-free soft brush or hair dryer to remove it gently.

- Stained with grease or fingerprint

Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or

paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change

the cloth and wipe several times if it is not clean enough.

Warning

Please use the standard accessories provided by manufacturer and make sure the device is

installed and fixed by professional installers.

Please prevent the device surface from the radiation of a laser beam when using laser beam

devices.

Please do not provide two or more power supply modes for the device, otherwise it may cause

damage to the device.

All installation and operations should conform to your local electrical safety codes. We assume

no liability or responsibility for all fires or electrical shock caused by improper handling or

installation.

Do not connect serval speed dome cameras to one power adapter. It may result in overheating

or fire if it exceeds the rated load.

Before you connect cable, install or uninstall or begin any work, please turn off the power and

ZM111317

unplug cable.

Please turn off power and unplug cables immediately if there is any smoke, bad smells, or noise.

Please contact technical support.

All work should be done by a trained service installer. We are not liable for any problems caused

by unauthorized modifications or attempted repair.

Please make sure no objects fall or flammable substances get into the speed dome camera. This

could result in fire, short-circuit or damage.

Please power down and unplug camera cables immediately if there is any liquid falling into or

inside camera.

Please use caution when locating a mounting location. Rain and sea water can erode the camera.

Notate the cameras IP rating for best application.

This series speed dome should be installed inside in a cool dry location away from sunlight.

This series speed dome should be kept away from strong electromagnetic radiant, please keep

away from wireless power, TV transmitter etc.

Statement

Please refer to the actual product for more details; the manual is just for reference.

The manual will be regularly updated according to the product update; the updated content will

be added in the manual without prior announcement.

Please contact the supplier or customer service if there is any problem occurring when using the

device.

Please contact customer service for the latest procedure and supplementary documentation.

There may be deviation between the actual value of some data and the value provided in the

manual due to the reasons such as the real environment is not stable and so on. Please refer to

the company’s final explanation if there is any doubt or dispute.

The company is not liable for any loss caused by the operation which is not followed by the

manual.

FCC Information

1. FCC conditions：

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

l This device may not cause harmful interference;

l This device must accept any interference received, including interference that may cause

undesired operation.

2. FCC compliance：

This equipment has been tested and found to comply with the limits for a digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference. This equipment generates and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful interference

ZM111317

to radio communication. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

l Reorient or relocate the receiving antenna.

l Increase the separation between the equipment and receiver.

l Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

l Consult the dealer or an experienced radio/TV technician for help.

Note:

Please refer to the website for more details, check and download corresponding user’s manual

and tool.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Download from WEB

Installation Accessories Bag

ZM111317

INTELLIGENT SPEED DOME INSTALLATION

PREPARATION

1.1

Basic Requirement

l All installation and operation here should conform to your local electrical safety codes.

l Before installation, please open the package and check all the components are included.

Please make sure the speed dome installation environment and installation mode can meet

your requirement. If there is special requirement, please contact your local retailer for more

information.

l We assume no liability or responsibility for all the fires or electrical shock caused by

improper handling or installation.

1.2

Check installation space and installation location

Please make sure the installation environment has enough space to install the speed dome and

its corresponding bracket.

Please make sure the ceiling, wall and the bracket can support the speed dome and its

corresponding installation component. It shall sustain 8X’s the weight of the speed dome.

1.3

Please keep all package material well for future use

Please keep speed dome package material well in case you need to send it back to your local

retailer or manufacturer for maintenance work.

Non-original package material may result in device damage during the transportation.

ZM111317

SETUP BEFORE INSTALLATION

2.1

Check Accessories

Before the installation, please check the accessories one by one according to the packing list.

Please make sure all the components listed are included.

2.2

Open Device

Remove the package and then take out the device. Please remove the dustproof feet mat from

the pedestal. See Figure 2-1.

Note

You do not need to remove the dustproof feet mat from the pedestal if you just put it on the

horizontal place (There is no ceiling mount or wall mount requirement).

Figure 2-1

2.3

About Ceiling Installation Position Map

The ceiling installation position map is to define hard ceiling hole positions and cable exit position.

The beeline part is the mechanical blind spot. Please paste it according to your actual

requirement to avoid mechanical blind spot. See Figure 2-2.

ZM111317

Figure 2-2

2.4

TF Card Slot and Reset Button

TF card slot and RESET button is shown as in Figure 2-3.

Press the RESET button for at least five seconds; you can restore factory default setup.

Press the WPS button on the speed dome and the router at the same time. The speed dome can

automatically connect to the network. ( SEE NETWORK SECTION BEFORE PROCEEDING TO KNOW

ALL OPTIONS)

Before you remove the SD card, please make sure it is not in read/write status; otherwise

you may lose data or result in SD card damage.

Figure 2-3

ZM111317

CEILING INSTALLATION

3.1

Installation Components

The ceiling installation dome body is shown as in Figure 3-1.

Figure 3-1

3.2

Ceiling Installation Steps

3.2.1 Installation Requirements

The ceiling mount speed dome can be installed in the hard construction wall in the indoor

environments. Before the installation, please make sure:

l The wall is thick enough to install the expansion bolt.

l The wall can at least sustain the 8x weight of the speed dome.

3.2.2 Installation Steps

1) The ceiling installation has two cable exit modes: One is to pull the cable through the

side cable exit of the speed dome without digging hole on the ceiling. The other is to dig

hole on the ceiling and pull the cable through the ceiling.

2) Confirm installation position and cable exit mode. Use the ceiling installation position

map to dig holes on the ceiling and then put the three plastic expansion bolts firmly.

3) Turn three quick installation screws to the screw holes at the bottom of the pedestal.

Pull the cable through according to your cable exit mode. Use three self-tapping screws

to secure the sheet metal on the ceiling. Insert the screws to the expansion bolts. See

Figure 3-2.

ZM111317

Figure 3-2

4) In Figure 3-3, line up the three quick installation screws at the bottom of the pedestal

and the concave to the three holes and the U slot at the sheet metal respectively. Turn

counter clockwise to secure the speed dome and the sheet metal closely.

Note

When the arrow of the ceiling installation position turns to the character “open” at the

side of the speed dome, you can see the speed dome and then sheet metal are closely

secured.

Figure 3-3

ZM111317

WALL MOUNT BRACKET INSTALLATION

4.1

Component Installation

Wall mount bracket is shown as below. See Figure 4-1.

Figure 4-1

4.2

Installation

4.2.1 Installation Requirements

The wall mount speed dome can be installed on the hard construction wall in the indoor

environments. Before the installation, please make sure:

l The wall is thick enough to install the expansion bolt.

l The wall can at least sustain the 8x weight of the speed dome.

4.2.2 Installation Steps

1). Please draw hole positions in the wall according to the holes of the bottom of wall mount base.

Then you can dig holes and insert the expansion bolts. Use four hex bolts and flat washer to fix

the wall mount base in the expansion bolts. See Figure 4-2.

ZM111317

Figure 4-2

2). Connect the hanging mount to the internal thread of the wall mount bracket. Secure screws to

the right side of the wall mount bracket to secure the hanging mount. Please note this step is

very important. Please make sure the screws are firm, otherwise, it may result in falling

risk of the intelligent speed dome. Use three self-captive screws to secure the sheet metal on

the hanging mount. See Figure 4-3.

Figure 4-3

3) Insert three quick installation screws to the holes at the bottom of the pedestal. Pull the

intelligent speed dome composite cable through the hanging mount and end of the column of the

ZM111317

wall mount bracket and pull it out of the other end of the wall mount bracket. Line up the three

quick installation screws at the bottom of the pedestal and the concave to the three holes and the

U slot at the sheet metal respectively. Turn counter clockwise to secure the speed dome and the

sheet metal closely. See Figure 4-4.

Note

When the arrow of the ceiling installation position turns to the character “open” at the side of the

speed dome, you can see the speed dome and then sheet metal are closely secured.

Figure 4-4

Connect cable connection at the wall mount base and then use four M8 screws to secure the wall

mount bracket on the wall mount base. See Figure 4-5.

ZM111317

Figure 4-5

ZM111317

5 Network Configuration

The IP camera defaults to DHCP. If you are connecting directly to NVR the NVR will assign the

IPC an IP address. If you are connecting IPC to XVR or hybrid DVR accepting IP camera or if

camera is connected directly on network router make sure you change to a static IP. NOTE:

ALWAYS CHANGE PASSCODE TO IP CAMERA FOR IMPROVED SECURITY.

5.1 Modify IP Address

IP address can be acquired and modified through our quick configuration tool for the cameras

which are accessed via wired network, it needs to connect wired network to configure wireless

parameters before using wireless network cameras. In this chapter, it will introduce the approach

of modifying IP address via “Quick Configuration Tool”; also, you can modify the IP address in

the network parameters of the WEB interface, please refer to the document link for Config Tool.

Note:

Currently the quick configuration tool only supports the cameras which apply to the same

network segment with computer IP address.

Step 1) Double click the “ConfigTools.exe” and open the quick configuration tool. See if your

camera is already in the list or click search at the top.

Step 2) Select device to be configured, the system will pop out the Modify IP Address box when

selecting Modify IP. Enter the static IP address and details to assign for this camera.

NOTE static IP is best way. DHCP will change and can cause configuration issues.

The default user name and password are admin and admin respectively, the default of port is

37777. See Figure 3-1 for more details.

Step 3)

ZM111317

Modify the camera IP address on the “Net” interface, click “Save” to finish modification.

See Figure 3-2 for more details.

5.2

Note:

Different devices may have different WEB interfaces, the figures below are just for reference,

please refer to our website for the latest documentation.

Step 1) Open IE and input the modified camera IP address in the address bar.

Step 2) The login interface is shown below, please input your user name and password (Default

user name is admin and password is admin respectively), click “login”. NOTE: Please

change the default passcode information for best security.

See Figure 3-3 for more details.

ZM111317

Figure 3-3

Step 3) Install controls according to the system prompt; see Figure 3-4 for the WEB main

interface. Please modify the administrator password as soon as possible after you successfully

logged in.

Figure 3-4

ZM111317

APPENDIX Ⅰ LIGHTENING PROTECTION AND SURGE

PROTECTION

This series speed dome adopts TVS lighting protection technology. It can effectively prevent

damages from various pulse signals below 4000W, such as sudden lighting and surge. While

maintaining your local electrical safety code, you still need to take necessary precaution

measures when installing the speed dome in the outdoor environment.

l The distance between the signal transmission cable and high-voltage device (or high-voltage

cable) shall be at least 50 meters.

l Outdoor cable layout shall go under the covering if possible.

l For vast land, please use sealing steel tube under the land to implement cable layout and

connects one point to the earth. Open floor cable layout is forbidden.

l In area of strong thunderstorm hit or near high sensitive voltage (such as near high-voltage

transformer substation), you need to install additional high-power thunder protection device

or lightning rod.

l The thunder protection and earth of the outdoor device and cable shall be considered in the

building whole thunder protection and conform to your local national or industry standard.

l System shall adopt equal-potential wiring. The earth device shall meet anti-jamming and at

the same time conforms to your local electrical safety code. The earth device shall not short

circuit to N (neutral) line of high voltage power grid or mixed with other wires. When connect

the system to the earth alone, the earth resistance shall not be more than 4Ω and earth

cable cross-sectional area shall below 25 mm2. See Figure 6-1.

Figure 6-1

ZM111317

APPENDIX Ⅱ 24V AC WIRE GAUGE AND TRANSMISSION

DISTANCE RELATIONSHIP SHEET

It is the recommended transmission distance when the cable diameter is fixed and the 24V AC

power consumption is below 10%. For the AC device, the max permission voltage power

consumption is 10%. For example, when a device of rated power 20W installed 141 inches (42m)

from the transformer, then the min cable diameter is 0.8000mm.

Feet（m）

0.8000

1.000

1.250

2.000

488.52（148.90）

763.31（232.66）

1192.67（363.53）

3053.25（930.63）

244.26（74.45）

381.66（116.33）

596.34（181.76）

1526.62（465.31）

162.84（49.63）

254.44（77.55）

397.56（121.18）

1017.75（310.21）

122.13（37.23）

190.83（58.16）

298.17（90.88）

763.31（232.66）

97.70（29.78）

152.66（46.53）

238.53（72.71）

610.65（186.13）

81.42（24.82）

127.22（38.78）

198.78（60.59）

508.87（155.10）

69.79（21.27）

109.04（33.24）

170.38（51.93）

436.18（132.95）

61.06（18.61）

95.41（29.08）

149.08（45.44）

381.66（116.33）

54.28（16.54）

84.81（25.85）

132.52（40.39）

339.25（103.40）

48.85（14.89）

76.33（23.27）

119.27（36.35）

305.32（93.06）

44.41（13.54）

69.39（21.15）

108.42（33.05）

277.57（84.60）

40.71（12.41）

63.61（19.39）

99.39（30.29）

254.44（77.55）

37.58（11.45）

58.72（17.90）

91.74（27.96）

234.87（71.59）

34.89（10.64）

54.52（16.62）

85.19（25.97）

218.09（66.47）

32.57（9.93）

50.89（15.51）

79.51（24.24）

203.55（62.04）

30.53（9.31）

47.71（14.54）

74.54（22.72）

190.83（58.16）

28.74（8.76）

44.90（13.69）

70.16（21.38）

179.60（54.74）

27.14（8.27）

42.41（12.93）

66.26（20.20）

169.62（51.70）

25.71（7.84）

40.17（12.25）

62.77（19.13）

160.70（48.98）

100

24.43（7.45）

38.17（11.63）

59.63（18.18）

152.66（46.53）

Page is loading ...

ZUUM Media LSPTZ-2MP-IP-2.7-11MM-IR30 Installation guide

Brand: ZUUM Media

Model: LSPTZ-2MP-IP-2.7-11MM-IR30

Type: Installation guide

Download PDF

report

ZUUM Media LSPTZ-2MP-IP-2.7-11MM-IR30 Installation guide

ZUUM Media LSPTZ-2MP-IP-2.7-11MM-IR30 Installation guide

Other documents