Autopot 1Pot XL System Operating instructions

Autopot
Brand
Autopot
Model
1Pot XL System
Type
Operating instructions

This manual is also suitable for

Autopot 1Pot XL System Pro is a flood and drain watering system designed to make growing plants easier and more efficient. It is a self-contained system that can be used to water up to four plants at a time. The system consists of a reservoir, a pump, and a series of pots and trays.

The reservoir holds the water and nutrients that are needed to feed the plants. The pump is used to circulate the water and nutrients from the reservoir to the pots. The pots are made of a porous material that allows the water and nutrients to seep into the soil. The trays are used to catch the excess water that drains from the pots.

Autopot 1Pot XL System Pro is a flood and drain watering system designed to make growing plants easier and more efficient. It is a self-contained system that can be used to water up to four plants at a time. The system consists of a reservoir, a pump, and a series of pots and trays.

The reservoir holds the water and nutrients that are needed to feed the plants. The pump is used to circulate the water and nutrients from the reservoir to the pots. The pots are made of a porous material that allows the water and nutrients to seep into the soil. The trays are used to catch the excess water that drains from the pots.

Simple care
guidelines
[email protected] I www.autopot-usa.com I +(1) 562 612 4182
Your 1Pot XL system
set-up guidelines
[email protected] I www.autopot-usa.com I +(1) 562 612 4182
Ensuring that the AQUAvalve5 floods
and drains correctly
Care and maintenance
Making sure your AQUAvalve5 floods and
drains correctly is simply achieved and
only takes a few seconds.
Hold the AQUAvalve5 at eye level so that
you can see the silicone fitted to the top
float resting on the hole below it.
The silicone must create a tight seal when
touching the hole.
If it looks like it is not sitting parallel on the
hole below, simply lift the top float and
apply pressure to one side of the silicone,
drop the float and hold at eye level again.
Repeat the procedure if necessary.
At the end of your growing season, clean
the AQUAvalve5 using warm soapy water.
Using an old tooth brush will help.
The AQUAvalve5 is easily disassembled.
The top float will slide all the way across
and the bottom float is unclipped from its
pivoting position. The circular discs fitted to
the top float can also be removed by using
pliers to grip the raised point.
At this point is it advisable to remove the
silicones to avoid them being lost.
It is also handy to have a paper clip or pipe
cleaner to hand so that you can push it
through the AQUAvalve5 nozzle, this will
remove any lime scale build up that may
have occurred during the growing season.
Blowing through the AQUAvalve5 nozzle
will also help to remove any build up. Do
not under any circumstances use a drill &
drill bit to clear the AQUAvalve5 nozzle.
This will potentially damage the
AQUAvalve5 beyond repair.
11
2
2
3
4
Ensure the silicone is sitting parallel
on the hole below it. Hold at eye level
to check the position is correct
1Pot XL system contents
• 1x 12.4 gallon reservoir & lid
• 2x 3/8” top hat grommet
• 1x 3/8” golf filter
• 1x 3/8” inline tap
• 1x 1Pot XL tray & lid
• 1x 6.6 gallon pot
• 1x AQUAvalve5
• 5ft of 3/8” pipe
• 1x PotSock Round
[email protected] I www.autopot-usa.com I +(1) 562 612 4182 If you require any guidance email - [email protected]
Advice
Plan views
and options
1Pot XL
dimensions
Advice
Using your front instruction sheet, repeat the module set up instructions for the number of trays.
Allow your plants to establish for 7-10 days before turning system on
1Pot XL setup
instructions
Suggested layout
• Pot up your plants, water through, then allow your plants to establish in the pots for a period of 7 to 10 days before
turning your system on. This will encourage a stronger and healthier root system.
• Always raise your reservoir/FlexiTank to a minimum of 6” above the highest AQUAvalve5 and re-fill the reservoir/
FlexiTank when there is approx. a 1/3 of the solution left – NEVER ALLOW THE RESERVOIR/FLEXITANK TO RUN EMPTY.
• With AQUAvalve5 systems mineral or organic fertilisers may be fed via the reservoir and pipework. Organic
fertilisers will require a water pump in the reservoir running for 15 mins every 2 hrs and cleaning of the reservoir,
pump, and filter each time the reservoir empties. Flush pipework with plain water every time the reservoir empties.
• Clean all substrate from the bottom and sides of the pots before placing in each tray.
This will ensure your system is clean from the start.
• Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles,
coco/clay pebbles, rockwool/clay pebbles.
¼" pipe
¼" top hat grommet
¼" inline tap
¼" golf filter
AQUAvalve
12.4 gal
reservoir
3/8" pipe
3/8" top hat grommet
3/8" inline tap
3/8" golf filter
AQUAvalve5
12.4 gal
reservoir
Connect your 3/8” pipe to the
relevant fitting
12.4 gal
reservoir
14.5"
11"
24"
6.6 gal
pot
13"
10.4"
14.6"
15.2"
13"
From the outside of the
module tray push the 3/8"
top hat grommet into the
hole in the module tray wall.
Pull
11
2
5Remove AQUAvalve collar
Push 3/8” pipe through
collar and attach to
AQUAvalve nozzle
Rescrew collar - DON’T
overturn... when you
feel it grip STOP
3
Thread approx 12" of
3/8" pipe into the tray
through the grommet.
Wetting the pipe end
will aid insertion.
4
Fill pot with medium
and pot up plants.
Water through pot
and allow to drain
outside the tray.
Position tray so it is level
Place pot in the tray, make
sure it is CLEAN!
Place lid over valve onto
tray
7Align the ‘half moon’
section on the rear of
the AQUAvalve with the
‘T’ section in the tray.
Firmly push the
AQUAvalve onto the ‘T’.
6
Remove any slack in the
3/8” pipe by drawing
excess out of the tray.
8
Cut 3/8” / 1/2” pipe to
appropriate length
1
Fit the PotSock Round
over the base of your
pot(s)
Push 3/8” top hat grommet
into tank, then push 3/8”
pipe through grommet.
Inside the tank push
3/8” filter into 3/8” pipe.
910
  • Page 1 1
  • Page 2 2

Autopot 1Pot XL System Operating instructions

Autopot
Brand
Autopot
Model
1Pot XL System
Type
Operating instructions
This manual is also suitable for

Autopot 1Pot XL System Pro is a flood and drain watering system designed to make growing plants easier and more efficient. It is a self-contained system that can be used to water up to four plants at a time. The system consists of a reservoir, a pump, and a series of pots and trays.

The reservoir holds the water and nutrients that are needed to feed the plants. The pump is used to circulate the water and nutrients from the reservoir to the pots. The pots are made of a porous material that allows the water and nutrients to seep into the soil. The trays are used to catch the excess water that drains from the pots.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents